GBC H410 User manual

CZ

RUS



Instruction Manual



Mode d’emploi



Bedienungsanleitung



Manuale d’istruzioni



Gebruiksaanwijzing



Instrucciones de servicio



Instrução de manejo



Bruksanvisning



Instrukcja obsługi



Návod k obsluze



Használati útmutató



 

aa

HeatSeal H410 High Speed 28pp 12/10/04 4:20 pm Page 1

EDNord - Istedgade 37A - 9000 Aalborg - Telefon 96333500

1

2

HeatSeal H410 High Speed

3

2 x 75 mic 2 x 100 mic 2 x 125 mic

Total 150 Total 200 Total 250

Copy Paper Setting 1-3 2-4 3-4

Brochure Paper Setting 2-5 2-5 3-5

Photo Paper Setting 4-7 5-8 8-10

HeatSeal H410 High Speed 28pp 12/10/04 4:20 pm Page 2

EDNord - Istedgade 37A - 9000 Aalborg - Telefon 96333500



Guarantee

Operation of this machine is guaranteed for two years from date of

purchase, subject to normal use.Within the guarantee period, GBC will

at its own discretion either repair or replace the defective machine free

of charge. Defects due to misuse or use for inappropriate purposes are

not covered under the guarantee. Proof of date of purchase will be

required. Repairs or alterations made by persons not authorised by GBC

will invalidate the guarantee. It is our aim to ensure that our products

perform to the specifications stated.This guarantee does not affect the

legal rights which consumers have under applicable national legislation

governing the sale of goods.

Register this product online at www.gbceurope.com

Electrical safeguards

• The unit must be connected to a supply voltage corresponding to the

electrical rating.

• Unplug the unit before moving it, or when it is not in use for an

extended period of time.

• Do not operate with a damaged supply cord or plug, if it is damaged,

or malfunctions.

• Do not overload electrical outlets beyond their capacity; fire or

electrical shock could result.

• The unit is intended for indoor use only.

• Do not spill liquid of any kind on this product.

• Close supervision is required when this product is used near children.

Service

• Do not attempt to service or repair the pouch laminator yourself.

Unplug the unit and contact an authorized GBC service

representative for any required repairs.

Cleaning

General safeguards

• Use the unit only for its intended purposes.

• Do not place anything in the throat opening of the unit other than

pouches/documents.

• Place unit on a secure, stable work area to prevent the unit from

falling and possibly causing personal injury and damage to the unit.

• Follow all warnings and instructions marked on the unit.

• The socket outlet shall be installed near the equipment and shall be

easily accessible.

Safety instructions

YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS IMPORTANT

TO GBC. IN THIS INSTRUCTION MANUAL AND ON THE PRODUCT ARE

IMPORTANT SAFETY MESSAGES. READ THESE MESSAGES CAREFULLY.

THE FOLLOWING WARNING IS FOUND ON THE BOTTOM OF THE

PRODUCT IN SEVERAL LANGUAGES.

This safety message means that you could be seriously hurt or killed if

you open the product and expose yourself to hazardous voltage.

Electrical shock hazard.

Do not open. No user

servicable parts inside.

Refer servicing to qualified

service personnel.

WARNING

Caution: Unplug this product before cleaning.



THE SAFETY ALERT SYMBOL PRECEDES EACH

SAFETY MESSAGE IN THIS INSTRUCTION MANUAL.

THIS SYMBOL INDICATES A POTENTIAL PERSONAL

SAFETY HAZARD THAT COULD HURT YOU OR OTHERS,

AS WELL AS CAUSE PRODUCT DAMAGE OR

PROPERTY DAMAGE.



WARNING: FOR YOUR PROTECTION DO NOT CONNECT

THE POUCH LAMINATOR TO ELECTRICAL POWER

UNTIL YOU READ THESE INSTRUCTIONS

COMPLETELY. KEEP THESE INSTRUCTIONS IN A

CONVENIENT LOCATION FOR FUTURE REFERENCE.

TO GUARD AGAINST INJURY, THE FOLLOWING

BASIC SAFETY PRECAUTIONS MUST BE

OBSERVED IN THE SET-UP AND USE OF THIS

PRODUCT.







Important safeguards



• Wipe exterior only with a damp cloth. Do not use detergents or

solvents.

Special notice

Thank you, for your recent purchase of a GBC Pouch Laminator.Your

new laminator may emit a slight odour during the initial stage of

operation. It is normal and will diminish after several hours of

operation.

HeatSeal H410 High Speed 28pp 12/10/04 4:20 pm Page 3

EDNord - Istedgade 37A - 9000 Aalborg - Telefon 96333500



Operation, hot lamination

1

Operation, cold lamination

Connect power cord to appropriate power source.

Push power button to “ON” position.The green power indicator will

illuminate.

Turn temperature knob to the cold setting.

Follow the instructions include with your GBC Self Adhesive

laminate or other pressure-sensitive, non-thermal laminating

pouches.

1

Connect power cord to appropriate power source.

Push power button to "ON" position.The green power indicator will

illuminate.

Using the included lamination guide, select appropriate

temperature setting for the pouch gauge thickness and material

you are laminating.

Temperature Setting Guidelines*

When laminating thin paper with light ink coverage, set the

temperature dial at the low end of the range.Thick paper and

heavy ink coverage require higher settings within the range.

Temperature setting will vary due to the finish, chemistry and heat

absorption properties of the material being laminated. If pouch is

cloudy the first pass through the machine, adjust temperature

higher and run through again. If waviness occurs, reduce the

temperature.Always allow sufficient time for laminator to adjust

to changes in temperature setting.

The inside of the laminator will glow red when the laminator has

reached operating temperature.

Position the item to be laminated into a GBC laminating pouch, so

that the document is aligned to the folded edge and right and left

borders are equal.

Insert the pouch and its contents straight into the machine, leading

with the sealed edge (fig. 1).

The laminated document will automatically exit the rear of the

laminator.After the pouch has stopped moving, place it on a flat

surface to cool before handling.

When you are finished laminating, push the power switch to “OFF”.

Do not laminate an empty pouch.

2

3

Anti-jam feature

How to use the Release Lever (fig. 2)

Turn off the laminator immediately

Press the release lever down to release the motor from the rollers

Pull your document back out of the laminator

Clean the rollers by running the cleaning sheet supplied with the

laminator through the machine 2 or 3 times in hot operation mode.

If you do not have this sheet just use or a similar cardboard sheet

that fits the width of the laminator

1

3

2

4

3

4

5

6

7

Specifications

Electrical

Machine Dimensions

Machine Weight

Maximum Pouch Width

Minimum/Maximum

Pouch Thickness

Maximum Thru-put Thickness

Warm-Up Time

GBC HeatSeal H410

High Speed

230V/50Hz/4.2A/1000W

500 x 190 x 114mm

3.9kg

324mm

2x75 mic. (TOTAL 150)

2x125 mic. (TOTAL 250)

0.7mm

5 min./2x75 mic. (TOTAL 150)

HeatSeal H410 High Speed 28pp 12/10/04 4:20 pm Page 4

EDNord - Istedgade 37A - 9000 Aalborg - Telefon 96333500

Page is loading ...

HeatSeal H410 High Speed 28pp 12/10/04 4:20 pm Page 27

EDNord - Istedgade 37A - 9000 Aalborg - Telefon 96333500

General Binding Corporation

Northbrook, IL 60062

USA

www.gbceurope.com

HeatSeal H410 High Speed 28pp 12/10/04 4:20 pm Page 28

EDNord - Istedgade 37A - 9000 Aalborg - Telefon 96333500

GBC H410 User manual

GBC H410 User manual

in other languages

Related papers

Other documents