Bimar WIND HOT Owner's manual



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

1

/

20

Assembly page 1/20

Fax +32 030 9904733

LIBRETTO ISTRUZIONI

NOTICE D'INSTRUCTIONS

INSTRUCTION BOOKLET

BEDIENUNGSANLEITUNG

TERMOVENTILATORE

FAN HEATER

THERMOVENTILATEUR

HEIZLÜFTER

type SVP25 (mod. HFH804)



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

2

/

20

Assembly page 2/20

Fax +32 030 9904733

I

A. Griglia aspirazione

B. Griglia uscita

C. Manopola selettore

D. Maniglia

UK

A. Air inlet

B. Air outlet

C. Selector Knob

D. Handle

F

A. Grille d'aspiration

B. Grille de sortie

C. Bouton du sélecteur

D. Poignée

D

A. Ansauggitter

B. Grid Ausfahrt

C. Drehknopf

D. Griff

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

7

/

20

Assembly page 7/20

Fax +32 030 9904733

Please read these instructions carefully before using the appliance, and instruct other persons using it,

too, when necessary.

KEEP BOOKLET HANDY FOR FURTHER USE.

GENERAL ADVISE

• This appliance is destined only to the heating of domestic or similar environments and in

compliance with these instructions. It can be considered only a supplementary source of heating

and not as a central heating element. The appliance must not be used in dusty environments or in

the presence of extremely volatile materials which could obstruct grids or heat exchanger, nor in

very damp environments, in the presence of inflammable products, or out of doors in the open. Any

other use is to be considered inappropriate and therefore dangerous. The manufacturer cannot be

held responsible for eventual damage caused by inappropriate, improper or irresponsible use and/or

for repairs made to the product by unauthorised personnel.

• The fan heater gets hot when working; so only touch the handle and plastic Knobs. Avoid contact

with the heating element.

• Ensure that the heating fan does not come into contact with water or other liquids. If this should

happen, never immerse hands in the liquid but remove the plug from the socket first of all. Dry the

appliance carefully and check that all the electric parts are dry. If in doubt, call a qualified expert.

• If the appliance should fall over or shows signs of faulty operation, disconnect the electrical cable

immediately. Check that no part is damaged and switch it on after the appliance has been

thoroughly checked: in case of doubt, contact qualified professional personnel.

• This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety. Children should be supervised to ensure that they do not play with the appliance.

• The appliance must be kept out of children’s reach.

• Attention: when using electric appliances, the basic safety precautions must always be

observed to avoid risks of fire, electric shocks and physical injury.

• Do not use the appliance if it is not operating correctly or seems damaged; if in doubt,

contact professionally qualified personnel.

• Unplug the appliance when not in use.

• The fireguard of this heater is intended to prevent direct access to heating elements and must

be in place when the heater is in use, but the fireguard does not give full protection for young

children and for infirm person.

• That the user must not leave the appliance unattended while it is connected to the supply.

• Do not touch the heater with wet hands or feet.

• Never use the radiator to dry damp garments.

• Do not expose the heater to the weather (sun, rain, etc.).

• Do not pull on the power cord or the appliance to unplug the appliance from the wall socket. Never

move the appliance by pulling the cord.

• If the electric cord is damaged, it has to be replaced by the supplier or an authorized service center

or a professionally qualified, to avoid any risks.

This symbol show: ATTENTION do not cover the appliance when it is operating to

avoid the risk of fires.



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

8

/

20

Assembly page 8/20

Fax +32 030 9904733

INSTALLATION

• After removing the packing materials, check the integrity of the heater; if you are unsure, do not

use it and ask for qualified professional help. The packing materials (plastic bags, polystyrene

foam, nails, etc.) must be kept out the reach of children because they are potential sources of

danger.

• Before connecting the appliance, check that the voltage shown on the data plate matches that of

your electricity (230V~50Hz). In the event of incompatibility between the electric outlet and the

plug of the heater, have the outlet replaced with another more suitable type by professionally

qualified personnel, who will make sure that the section of the wires of the outlet is appropriate for

the absorbed power of the heater (10A). Check that the mains are not connected equipment; high

absorption to prevent overloading and fire risks. In general, the use of adapters or extension cords

is not recommended; if their use is indispensable, they must conform to existing safety standards

and their current capacity (amperes) must not be less that the maximum of the heater.Attention:

before use the appliance remove the detachable coupon to stick the handle.

• Before each use, verify that the heater is in good condition and that the electrical cord is not

damaged: in the case of doubt, ask for professionally qualified help.

• Make sure that the cable is correctly positioned and that it is not in contact with hot parts or sharp

edges, nor wrapped around the device or twisted.

• The power socket must be easy to reach so the plug can be removed quickly in case of emergency.

• Position the fan heater far from other sources of heat, inflammable materials (curtains, carpets,

etc.), inflammable gases or explosive materials (spray cans) and from materials that can deform on

exposure to heat. Make sure that there is 100 cm of free space in front of the fan heater and 30 cm

on the sides. Do not use the heater in the immediate vicinity of a bathtub, shower or swimming

pool (to avoid drops of water falling on the heater or the heater falling in the water), or in places

where it could be subject to shocks.

• Make sure that the fan heater is working correctly: if not, turn the heater off and have it checked by

professionally qualified personnel.

• Make sure that the air-intake grid is not obstructed by objects, fabrics or anything else to avoid the

heater overheating or breaking.

• Do not use the appliance with a timer or a programmer or with a system that can switch on the

appliance automatically, to avoid risk of fire, since a fire risk exists if the heater is covered or

positioned incorrectly. Check that no other high absorption appliances are connected to the same

power source.

• In the case of a breakdown or fault, switch off the appliance and have it checked by a

professionally qualified technician; repairs made by unqualified persons can be dangerous and

render void the warranty.

• The appliance can be used standing on a level horizontal surface or fastened vertically to a wall.

Instructions for installation are given below.

Horizontal installation

The surface must be stable, rigid, and not sloping (otherwise the appliance could tip), ample and

free of any debris. Shelves cannot be used.

Vertical installation

Follow the indications given in the illustrations when fitting the appliance to the wall: Pay attention

not to perforate any pipes or conducts inside the wall. The fastening holes must be horizontal with

an inter-axis of 162mm, at a distance of at least 50cm from the ceiling and side walls, and at least

120cm from the floor. The hole for the locking flange must be made 170mm below the previous 2.

It is not in the centre between the previous holes but slightly aside, 97mm with respect to the

vertical of the left hole, and 65mm with respect to the vertical of the right hole.



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

9

/

20

Assembly page 9/20

Fax +32 030 9904733

• The wall must be robust, flat, with no rough patches, in a rigid fire-proof and heat-resistant

material, with a suitable thickness to ensure that the appliance is fixed securely, bearing in mind

that it can be oriented in various directions and therefore the wall must withstand a certain stress.

• The appliance must be fixed using the appropriate holes and secured using the metal plate

supplied with all the other screws and dowels. Fastening must be solid and secure.

• The appliance must be turned so that air is blown downwards and not upwards.

FUNCTIONS

Before each use, verify that the unit is in good condition, the electric cord is not damaged, if the

power cord is damaged, it must be replaced by the manufacturer or a competent qualified electrician

or a person with similar qualifications, in order to avoid any risk.

The fan heater has a selector switch and by turning the relative knob “C” clockwise, the following

functions can be selected:

0= off

only ventilation,

I = warm air (1000W) I I = hot air (2000 W)

The heating element can turn 90°, and its support allows it to be turned to 4 different positions,

locking it automatically. For positioning and/or to move the appliance, use the handle “ D “.

Follow these steps when using the fan heater:

1. Check that the selector is in position “0” (off)

2. Turn the heating unit to direct the air in the most suitable direction.

3. Insert the plug in the power socket

4. Switch on the appliance by turning the selector knob clockwise to the function required.

5. Switch off the appliance by turning the selector knob to “0” and remove the plug from the power

socket.

Always remove the plug from the power socket after using the appliance.

CLEANING AND MAINTENANCE

Attention: before cleaning the appliance, turn it off, remove the plug from the outlet and wait for it to

cool.

• Periodically check that the air-intake grill is not obstructed by fuzz or threads.

• Use a soft, slightly damp cloth to clean the body; do not use metal scouring pads or abrasive

products.



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

10

/

20

Assembly page 10/20

Fax +32 030 9904733

• To clean and maintain of the grid, it is possible vacuum cleaner paying attention not to damage the

electrical resistance.

• A special tool is required to replace the electrical cord: contact an authorized service center, also

for any repairs.

• When the appliance is not being used, cover it and put it in a dry place. it is a good idea to put it

back in its original packaging to protect it from dust and humidity.

• If you decide not to use the fan heater, we recommend that you make it inoperative by cutting the

power cord (but first make sure you have removed the plug from the electrical outlet), and make

those parts harmless that are dangerous when played with by children.

• Do not dispose of non-biodegradable products in the environment but dispose of them in

accordance with current law. At the end of its working life, the product must not be disposed of as

urban waste. It must be taken to a special local authority differentiated waste collection centre or to

a dealer providing this service. Disposing of a household appliance separately avoids possible

negative consequences for the environment and health deriving from inappropriate disposal and

enables the constituent materials to be recovered to obtain significant savings in energy and

resources. Bear in mind that: the body, the electrical wires are copper coated in rubber. – The

electric motor is made of iron and copper. The electrical resistance is made of iron.

Page is loading ...



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

19

/

20

Assembly page 19/20

Fax +32 030 9904733



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Bimar

(Italy). The pages must be reproduced and folded in

order to obtain a booklet A5 (+/- 148.5 mm width x 210

mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t

change the page numbering. Keep the language

integrity.

20

/

20

Assembly page 20/20

Fax +32 030 9904733

Via G.Amendola, 16/18

25019 Sirmione (BS) – ITALY

www.bimar-spa.it e-mail: info@bimar-spa.it

Servizio clienti Bimar: 8955895542

Bimar WIND HOT Owner's manual

This manual is also suitable for

Bimar WIND HOT Owner's manual

in other languages

Related papers

Other documents