Estate Design SAWALL-1350 Installation guide

Brand: Estate Design

Model: SAWALL-1350

Category: Fireplaces

Type: Installation guide

Estate Design SAWALL-1350 is a versatile electric fireplace heater that can be used as a freestanding unit or mounted on the wall. It features realistic flame effects, adjustable heat settings, and a remote control for added convenience. With its compact design and easy assembly, the SAWALL-1350 is a great way to add warmth and ambiance to any room. Whether you're looking to cozy up on a cold night or simply create a relaxing atmosphere, this fireplace heater is the perfect solution.

PREPARATION

This carton includes GLASS! ALWAYS use extreme caution when handling glass.

Failure to do so could result in personal injury or property damage.

Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts

and assembly steps are grouped for free-standing or wall-hanging use. Check the parts list to make

sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.

Free-Standing Mode: You will need Part A, Part B, Box 1, Box 2, Box 3, Box 4, and the

following tools (not included): Phillips screwdriver.

Wall-Hanging Mode (Drywall installation only): You will need Part A, Part B, Part

C, Part 6, Box 1, Box 2, Box 5, and the following tools (not included): Phillips screwdriver; stud finder;

level; tape measure; electric drill; 1/16” wood drill bit.

Concrete walls: DO NOT use these anchors. Consult a professional for proper anchoring methods.

PARTS AND HARDWARE

A – Firebox ( 1 )

B – Front Glass Panel ( 1 )

NOTE: The wall mount bracket (C) is attached to the

back of the firebox (A) by two thumb screws (6).

C – Wall Mount Bracket ( 1 )

6 – Thumb Screws ( 2 )

NOTE: Unscrew both thumbscrews (6) from the top of the firebox (A). KEEP the thumb screws. Remove the

wall mount bracket (C) from the firebox whether you will use the unit in free-standing or wall-hanging mode.

PARTS & HARDWARE - GENERAL

Box 1 – Remote Control & Machine Screws Box 2 – Decorative Stones

2 – M4x8 Machine

Screws ( 2 )

WS – White Stones ( set )

RC – Remote Control ( 1 )

RC Battery ( 1 )

CS – Clear Faux Stones ( set )

PARTS & HARDWARE: FREE-STANDING MODE

Box 3 – Pedestal Leg Parts and Hardware Box 4 – Pedestal Base

E – Pedestal Leg

( 1 )

G – Pedestal Leg

Cover ( 1 )

1 – M5x12 Machine

Screws ( 8 )

F – Pedestal Base Assembly

( 1 )

PARTS & HARDWARE: WALL-HANGING MODE

Box 5 – Wall Hanging Hardware

3 – M5x40 Wood Screws ( 4 )

4 – M4x30 Drywall Screws ( 4 )

5 – M15x40 Drywall Anchors ( 4 )

ASSEMBLY: FREE-STANDING MODE

ALWAYS unplug this fireplace heater before assembly or cleaning

, or before

relocating. Failure to do so could result in electric shock, fire, or personal injury.

STEP 1. Lay the firebox (A) on its back. Align the holes in the pedestal leg (E) with the threaded

inserts in the firebox. Thread one M5x12 machine screw (1) through each hole in the pedestal leg

and into the threaded inserts. Check the leg alignment. Tighten securely with a Phillips screwdriver.

STEP 2. Press the pedestal leg cover (G) into the pedestal base assembly (F). Snap into place.

STEP 3. Lay the firebox on its back so the pedestal leg (E) hangs over the edge of a table. Or,

have an adult helper lift the bottom edge of the firebox. Slide the pedestal leg cover and base (F/G)

over the pedestal leg (E). Make sure the power supply cord comes out from the notch in the

pedestal leg cover. Thread one M5x12 machine screw (1) through each hole in the pedestal base,

into the threaded holes in the pedestal leg. Tighten securely with a Phillips screwdriver.

Notch for

Power Cord

These holes will

align with the

threaded inserts

F/G

ALWAYS keep these stones OUT OF REACH OF CHILDREN! Leave no stones

where children can find them. Failure to do so could cause a choking hazard.

STEP 4. Stand the fireplace up and set it on a sturdy level surface at or near where you plan to use

it. Carefully arrange the decorative stones (WS/CS) along the inset window ledge at the front of the

firebox. Use care when relocating the fireplace to prevent the decorative stones from falling out.

The next step requires installation of a GLASS panel!

The manufacturer recommends

that two adults install the glass panel. Always use extreme caution when handling glass.

Failure to do so could result in personal injury or property damage.

STEP 5. 1. Carefully set both hooks of the front glass panel (B) into the slots at the top front edge

of the firebox (A). 2. Press the two posts of the glass panel into the locking slots near the lower

corners of the front firebox panel. NOTE: Make sure the posts click into the slots. This will keep

the decorative glass in place. 3. Thread the M4x8 machine screws (2) through the glass panel

hooks and into the threaded holes in the firebox. Partially tighten by hand. Check the alignment of

the glass panel and securely tighten the screws with a Phillips screwdriver.

Hook

Post

Slot

WS/CS

Free-Standing Mode: Fully Assembled

ASSEMBLY: WALL-HANGING MODE



STEP 1. Find a safe location. Minimum clearance on each side must be at least 2 inches (50mm);

minimum clearance from the floor must be at least 4-3/8 inches (11.1 cm); minimum clearance from

the front must be at least 3 feet (90 cm). Choose a location near an outlet so an extension cord is

not required. DO NOT position the unit directly below a power outlet. See Safety Information on

pages 3 and 4 for more warnings about placement, installation, and use of this product.

NOTICE

The wall mount fasteners included with this fireplace are for use ONLY with a

wood-framed wall covered in drywall (sheet rock). For concrete walls

, cinder

blocks, or other wall types, consult a professional for the best attachment methods.

Minimum 4-3/8 inches

Wall or other

objects at side

Wall or other

objects at side

Floor or other

surface

Minimum 2 inches

from edge of glass

Minimum 2 inches

from edge of glass

STEP 3. Locate the wall studs using an electronic stud-finder. Studs are spaced 16” apart as

measured from the center of each stud. The holes in the mounting bracket (C) will align with the

wall studs. The end of each arm has a set of three holes. Select one set of holes (left, center, or

right) when attaching the mounting bracket to the wall. There are also two holes on the center post.

AVOID INJURY and DAMAGE! Four screws should be screwed directly into wall

studs. If that is not possible, at least two screws

must be screwed directly into wall

studs, AND four additional screws

must also be screwed into the drywall anchors.

STEP 4. Position the wall mount bracket (C) over the wall studs. Level the mounting bracket and

mark the four holes with a pencil. Set the wall mount bracket aside. Drill a pilot hole at each marked

point using a 1/16” wood drill bit. Make sure each hole goes into a wall stud.

16”

Studs

Drywall

Hook

Tab

16”

Note: The wall mount bracket

tabs are on the upper arms and

the hooks are on the lower arms.

STEP 5. Thread one M5x40 wood screw (3) through the bracket, into the pilot hole, and into the

stud. Partially tighten. Make sure the bracket is level. Thread the remaining three

M5x40 wood

screws into the other three holes. Check the alignment and tighten each screw securely with the

Phillips screwdriver. Check each screw to make sure it is tight, and that the bracket is secure.

STEP 6. If only one wall stud is available, the wall mount bracket must be secured to the wall with

two M5x40 wood screws (3) though the two center post holes AND four M4x30 drywall

screws (4) through one other set of bracket holes. DO NOT attach the wall mount bracket to the

wall studs with one of the outer sets of holes as the bracket will not be stable. Use the center holes.

STEP 7. Center the wall mount bracket (C) over the wall stud. Level the mounting bracket and

mark the two center post holes with a pencil. Mark the four outer holes for the drywall anchors. Set

the wall mount bracket aside until STEP 8.

STEP 8. Drill pilot holes into the two center marks using a 1/16” wood drill bit. Make sure each pilot

hole is drilled directly into a wall stud. Next, use a Phillips screwdriver to screw the four drywall

anchors (5) into the drywall until they are flush with the surface. DO NOT OVERTIGHTEN.

STEP 9. Thread the two M5x40 wood screws (3) through the center post holes, into the pilot holes,

and into the wall stud. Partially tighten. Make sure the bracket is level. Thread the four M4x30

drywall anchor screws (4) through the wall mount bracket and into drywall anchors.

DO NOT OVER-TIGHTEN! This may loosen the anchors or damage the drywall. Check the

alignment and tighten each screw securely with a Phillips screwdriver. Be sure the bracket is secure.

ALWAYS unplug this fireplace heater before assembly or cleaning

, or before

relocating. Failure to do so could result in electric shock, fire, or personal injury.

STEP 10. With the firebox (A) at an angle, fit the slots in the back of firebox (A) over the hooks on

the wall mount bracket, and carefully press the top of the firebox against the wall mount bracket.

The slots at the top edge of the firebox should slide over the wall mount bracket tabs. Hold the

firebox in place and thread the thumb screws (6) through the holes in the firebox and into the wall

mount bracket tabs. Tighten both thumb screws and make sure the firebox is secure to the wall.

ALWAYS keep these small stones OUT OF THE REACH OF CHILDREN!

NEVER leave stones where children can find them

. Failure to do so could cause a

choking hazard.

STEP 11. Carefully arrange the decorative stones (WS/CS) along the inset window ledge at the

front of the firebox. Use care when relocating the fireplace to prevent the stones from falling out.

The next step requires installation of a GLASS panel!

The manufacturer recommends

that two adults install the glass panel. Always use extreme caution when handling glass.

Failure to do so could result in personal injury or property damage.

STEP 12. Set both hooks of the front glass panel (B) into the slots at the top front edge of the

firebox (A). Press the two posts of the glass panel into the locking slots near the lower corners of

the front firebox panel. NOTE: Make sure the posts click into the slots. This will keep the

decorative glass in place. 3. Thread one M4x8 machine screw (2) through each glass panel hook

and into the threaded hole in the firebox. Partially tighten by hand. Check the alignment of the glass

panel and securely tighten the screws with a Phillips screwdriver.

WS/CS

Post

Slot

Hook

Estate Design SAWALL-1350 Installation guide

Brand: Estate Design

Model: SAWALL-1350

Category: Fireplaces

Type: Installation guide

Download PDF

report

Estate Design SAWALL-1350 Installation guide

Estate Design SAWALL-1350 Installation guide

Related papers

Other documents