Marantz VP-12S1 User manual

Brand: Marantz

Model: VP-12S1

Category: Data projectors

Type: User manual

This manual is also suitable for

VP-12S1s

Model VP-12S1

User Guide

DLP

Projector

The lightning symbol in the triangle, is

intended to alert the user to the presence of

uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation mark in the triangle is

intended to alert the user to the presence of

important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

For the customers in the USA:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

- Reorient or relocate the receiving antenna.

- Keep an appropriate distance between the equipment and

the receiver.

- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

NOTE:

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

For the customers in Canada:

This Class B digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment regulations.

IMPORTANT SAFETY

INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

This product was designed and manufactured to meet strict quality

and safety standards. There are, however, some installation and

operational precautions which you should be particularly aware of.

1. Read these Instructions: All the safety and operating

instructions should be read before the appliance is operated.

2. Keep these Instructions: The safety and operating instructions

should be kept for future reference.

3. Heed all Warnings: All warnings on the appliance and in the

operating instructions should be adhered to.

4. Follow all Instructions: All operating and use instructions should

be followed.

5. Cleaning: Unplug this video product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning, and clean only with dry cloth.

6. Attachments: Only use attachments/accessories specified by

the manufacturer.

7. Water and Moisture: Do not use this video product near water

such as, near a bath tub, wash bowl, kitchen sink, or laundry

tub, in a wet basement, or near a swimming pool, and the like.

8. Accessories: Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

9. Ventilation: Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the video product

and to protect it from overheating, and these openings must not

be blocked or covered. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions. Do

not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat. This video product should not be placed in a

built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer’s instructions have

been adhered to.

10. Power Sources: This video product should be operated only

under the type of power source indicated on the marked label. If

you are not sure of the type of power supply for your home,

consult the appliance dealer or a local power company. For

video products intended to operate with battery power, or other

sources, refer to the operating instructions.

11. Grounding or Polarization: Do not defeat the safety purpose of

the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has

two blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

AC POLARIZED PLUG

12. Power-Cord Protection: Protect the power code from being

walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

13. Protective Attachment Plug: The appliance is equipped with an

attachment plug having overload protection. This is a safety

feature. See Instruction Manual for replacement or resetting the

protective device. If the plug needs to be replaced, be sure that

the service technician has used a replacement plug specified by

the manufacturer that has the same overload protection as the

original plug.

14. Lighting: Unplug this apparatus during lightning storms or when

unused for long periods of time.

15. Power Lines: An outside antenna system should not be located

in the vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system, extreme

care should be taken to keep from touching such power lines or

circuits. Any contact with them might be fatal.

16. Overloading: Do not overload wall outlets and extension cords

as this can result in a risk of fire or electric shock.

17. Object and Liquid Entry: Never push objects of any kind into this

video product through openings as they may touch dangerous

voltage points or short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind on the video product.

18. Servicing: Do not attempt to service this video product yourself

as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to a qualified

service personnel.

19. Damage Requiring Service: Servicing is required when the

apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

20. Replacement Parts: When replacement parts are required, be

sure that the service technician has used replacement parts

specified by the manufacturer or have the same characteristics

as the original part. Unauthorized substitutions may result in

fire, electric shock or other hazards.

21. Safety Check: Upon the completion of any service or repairs to

this video product, ask a service technician to perform safety

checks to determine that the video product is in proper

operating condition.

22. Carts and Stands: The appliance should be used only with a

cart or stand that is recommended by the manufacturer.

23. An appliance and cart combination should be handled with care.

Quick stops, excessive force, and uneven surfaces may cause

the appliance and cart combination to overturn.

24. When the projector is mounted on the ceiling, the Ceiling Mount

Kit approved by MARANTZ must be used for installation.

25. Do not look into the lens when the projector is turned on. It

could damage your eyesight.

26. Unplug the projector from the wall outlet if it is not to be used for

a few days.

ENGLISH

FEATURES ................................................................................................................... 1

PROJECTOR LAYOUT AND FUNCTIONAL OVERVIEW ........................................... 2

Front and Top .................................................................................................... 2

Right Side and Rear .......................................................................................... 3

Bottom ............................................................................................................... 5

Height Adjustment ............................................................................................. 5

Remote Controller .............................................................................................. 6

Preparing the Remote Controller ....................................................................... 7

INSTALLATION ............................................................................................................ 8

Recommended Setting ...................................................................................... 8

Distance between the projector and the screen (throw distance) ...................... 9

Image Position Adjustment .............................................................................. 10

Advanced Setting ............................................................................................. 11

The Screen Image in a Wide screen (16:9) ..................................................... 12

The Screen Image in a 4:3 screen ................................................................... 13

CONNECTION ............................................................................................................. 14

Connections with Video equipment ................................................................. 14

Connection with a HD-Video or PC ................................................................. 14

Connection with a DV camcoder ..................................................................... 15

Advanced connection ...................................................................................... 15

INITIAL SET UP .......................................................................................................... 16

TO TURN OFF THE POWER ...................................................................................... 16

OPERATIONS ............................................................................................................. 17

Menu ................................................................................................................ 17

Picture Adjust ................................................................................................... 17

Setting .............................................................................................................. 17

Display ............................................................................................................. 18

Configuration ................................................................................................... 18

Trigger2 ........................................................................................................... 19

Memory ............................................................................................................ 19

Lamp Life and Replacement Lamp .................................................................. 20

MAINTENANCE .......................................................................................................... 21

Replacing Lamp Unit ....................................................................................... 21

Cleaning the lens ............................................................................................. 21

Replacement parts ........................................................................................... 21

Optional accessories ....................................................................................... 21

TROUBLESHOOTING ................................................................................................ 22

ERROR MODE ............................................................................................................ 22

ON SCREEN MESSAGE ............................................................................................ 23

SPECIFICATIONS ....................................................................................................... 23

DIMENSIONS .............................................................................................................. 25

TABLE OF CONTENTS

INTRODUCTION

SET UP PROCEDURES

OPERATIONS

ADDITIONAL

INFORMATION

ENGLISH

FEATURES

Optics

• Texas Instruments Digital Light Processing Technology

• High Definition Panel (1280 x 720), DMD

• 16 : 9 Aspect Ratio

• Newly developed custom optics by Minolta

• 1200 : 1 Contrast Ratio

• 700 ANSI Lumens Brightness

• Brightness Uniformity : 90 %

• No Halo Effect

• Lens Up/Down Shift construction

• Short Throw Distance: 80"-8.6ft (2.6m), 100"-10.9ft (3.3m)

• Dust Free optics Sealing

• No Light Leakage (Double Seals Cabinet Structure)

• Extremely Quite (Noise Cancel Duct Construction, Ceiling

Color Wheel Motor)

• Long Life Lamp (Average 2000 Hours)

• Double Shrink Seal Lamp Structure minimizes Burst Ratio

Electronics & Software

• Full Digital device

• 3 Faroudja Chips Inside (Decoder, Doubler, and Enhancer)

• 3-2 pull down

• 10-Bit Digital Gamma Processing

• Horizontal Keystone Correction

• 480p, 720p,1080i adapted

• IEEE 1394 DV Format adapted for Digital Video Camera

Playback

• PC Signal VGA to XGA

• Three Picture Modes: Theater, Standard, Dynamic

• Nine Picture memories

• 4 Aspect Modes

• Three Color Temperatures

• Black Level Selection

• Control through RS232C

• Two trigger for powered Screen Control

• Ecology Lamp mode

– DLP, Digital Micromirror Device and DMD are trademarks

of Texas Instruments.

– “DCDi” is a trademark of Faroudja, a division of Sage Inc.

– “i.LINK” and the “i.LINK” Logo are trademarks.

– Even if no trademarks are indicated, they are greatly

valued.

Note: Pixel defects

DMD

(Digital Micromirror Device

) is one of the most

advanced technologies for consumer products. The

DMD

made by high precision technology, however some

pixel defects may be found on the projected image. We

are trying our best to control the quality in order to reduce

the number of defective pixels. It is almost impossible to

have zero pixel defects, even using the most advanced

technology. This is not a problem only for Marantz, but all

DLP

projector manufactures. Therefore we have to note

that the warranty does not cover the DMD

for pixel

defects. We appreciate your understandings.

Note: Lamp

SHP lamp is one of the most advanced technologies for

consumer products. The lamp made by high precision

technology, however some lamps might be failing before it

reaches its life. And projector’s brightness is getting

darker along with accumulated lamp usage hours. We are

trying our best to control the quality in order to reduce

lamp failures. It is almost impossible to have zero failure,

even using the most advanced technology. This is not a

problem only for Marantz, but all projector manufactures.

Therefore we have to note that the warranty does not

cover the SHP lamp for lamp failures: explosion, and non-

lighting except initial use. And also we have to note that

the warranty does not cover the SHP lamp for lamp

failures: flickering, and getting darker along with

accumulated lamp usage hours. We appreciate your

understandings.

INTRODUCTION

ENGLISH

q IR sensor (front and rear)

w Projection Lens

e Ventilation holes

Notes:

• Do not place anything near the ventilation holes to avoid

overheat inside the unit.

• Do not place your hand or objects near the ventilation

holes; the air is coming out.

r Adjustable feet

Adjust the vertical angle of the projector.

t Focus ring

Adjust the picture focus.

y Zoom ring

Adjust the size of the projected image.

u Lens Shift knob

Manually adjust the position of the image vertically.

i POWER key

Press to turn the projector ON or STANDBY mode.

Front and Top

VP-12S1

r r

!2u

!5 !4

!1 o !0 !6

PROJECTOR LAYOUT AND FUNCTIONAL OVERVIEW

o POWER ON indicator

Lights up when the power is turned on. Flashes while the

projector goes into standby mode for about one minute.

!0 STANDBY indicator

Lights up when the power is turned off.

!1 MENU key

Display the on-screen menu.

!2 The 3 / 4 / 1 / 2 keys

Control the MENU cursor.

!3 ENTER key

Confirm "Reset All", "Reset Lamp Life", "New Lamp?".

!4 INPUT SELECT key

When the key is pressed, the unit toggles between

COMPONENT, S-VIDEO, VIDEO, and RGB inputs.

!5 FOCUS key

Display a focus pattern.

!6 WARNING/LAMP indicator

Flashes or lights up when something is wrong with the lamp

cover, lamp, fan, or temperature inside the projector.

INTRODUCTION

ENGLISH

z COMPONENT VIDEO IN

Y, PB

/CB, PR/CR connectors.

Connect the COMPONENT VIDEO output from video

equipment or an A/V processor/receiver with a component

video output.

x S-VIDEO IN

Connect the S-VIDEO output from a video equipment.

c VIDEO IN

Connect the composite video output from a video equipment.

v RGB IN

Connect the analog RGB output from a computer equipment.

b AUX DV IN

Connect the i.LINK(DV-SD format) output from a video

equipment.

n AUX OPTICAL

Connect the optical input from an audio equipment.

Audio out terminal of DV-IN signal.

VP-12S1

m⁄4⁄6⁄5 ⁄0,⁄3 ⁄2

⁄7

x nbv

⁄1.

Right Side and Rear

m AUX AUDIO OUT (DIGITAL)

Connect the COAXIAL input from an audio equipment.

Audio out terminal of DV-IN signal.

, REMOTE CONTROL IN/OUT

By connecting this projector to another Marantz audio

component using a supplied System Control cable, you can

remotely operate the components as a single system.

• When connecting to component with a remote sensor

(such as the SR-14,SR-18,SR-19), be sure to connect the

"REMOTE CONTROL IN" jack of this projector to the

"REMOTE CONTROL OUT" jack of the component with

the remote sensor.

• When connecting to component which is not equipped

with a remote sensor, be sure to connect the component

to the "REMOTE CONTROL OUT" jack of this projector.

. REMOTE switch (EXTERNAL/INTERNAL)

When using this projector independently, set this switch to

"INTERNAL". When using this projector in a system with a

Marantz DVD player or AV Receiver equipped with a remote

sensor, set the switch to "EXTERNAL".

⁄0 TRIG.1(TRIGGER 1)

When the unit is turned on, 12V is output. When the unit is

turned off, no voltage is output. This allows such as a powered

up/down screen,whenever the projector is turned on or off.

ENGLISH

⁄1 TRIG.2(TRIGGER 2)

Select ON or OFF at each aspect mode, such as Full,

Normal, Zoom, and Through to control screen aspect ratio

with powered up/down dual aspect ratio screen.

Note:

Do not use TRIG.1 and TRIG.2, as the power source.

⁄2 LIGHT ON/OFF

Select ON : The connector panel lights up.

⁄3 RS232C

Connect the RS232C of equipment for external control.

⁄4 AC IN

Connect the supplied AC power code.

⁄5 Lamp cover

⁄6 Lamp cover securing screw

⁄7 Ventilation holes

Notes:

• Do not place anything near the ventilation holes to avoid

overheat inside the unit.

• Do not place your hand or objects near the ventilation

holes; the air is coming out.

INTRODUCTION

ENGLISH

Height Adjustment

How to use adjustable feet and adjustment lever.

(1) Release the adjustable feet. (2) Detail adjustment

PRESS

DOWN

Note : Lift the unit up carefully.

Bottom

q Adjustment lever

Lift the projector and turn the adjustment lever right or left.

The adjustable feet will extend from the projector. Then,

release the lever, the adjustable feet is locked.

w Ventilation holes

Notes:

• Do not place anything near the ventilation holes to avoid

overheat inside the unit.

• Do not place your hand or objects near the ventilation

holes; the air is coming out.

ENGLISH

a POWER ON key

Turn the projector on.

s STANDBY key

Turn the projector off.

d 3 / 4 / 1 / 2 keys

Control the MENU cursor.

f ENTER key

Confirm "Reset All", "Reset Lamp Life", "New Lamp?".

g MENU key

Display the on-screen menu.

h COMPONENT key

Select the COMPONENT VIDEO IN signal.

j S-VIDEO key

Select the S-VIDEO IN signal.

k VIDEO key

Select the VIDEO IN signal.

Remote Controller

l RGB key

Select the RGB IN signal.

¡0 THEATER key

Select the Theater picture mode.

When the key is pressed, the mode toggles Theater1,

Theater2, Theater3 and Theater Default.

¡1 STANDARD key

Select the STANDARD picture mode.

When the key is pressed, the mode toggles Standard1,

Standard 2, Standard 3, and Standard Default.

¡2 DYNAMIC key

Select the Dynamic picture mode.

When the key is pressed, the mode toggles Dynamic1,

Dynamic2, Dynamic3 and Dynamic Default.

Note :

If you need discrete command for above picture modes, you

can down load from "www.marantz.com".

¡3 INFO key

Turn the information menu on or off.

¡4 CINEMA key

Press to turn the CINEMA mode – auto 3-2 pull down mode

– on or off.

¡5 NORMAL key

Select NORMAL mode from four aspect ratio modes.

¡6 FULL key

Select FULL mode from four aspect ratio modes.

¡7 ZOOM key

Select ZOOM mode from four aspect ratio modes.

¡8 THROUGH key

Select THROUGH mode from four aspect ratio modes.

¡9 AUX key

Select the AUX IN (DV IN) signal.

™0 FOCUS key

Display a focus pattern.

™1 V-MUTE key

Cuts off the picture.

¡2

¡5

¡7

™1

¡1

¡4

¡0

¡3

¡4

¡9

¡8

™0

PROJECTOR

INTRODUCTION

ENGLISH

1. Open the cover.

2. Insert batteries (AA).

Make sure to match the + and – marks on the batteries

with inside the battery compartment.

3. Close the cover.

CAUTION

– The available battery types are limited: manganese dry

cell and alkaline dry cell.

– Do not mix different battery types.

– Do not mix old and new batteries.

– Only batteries of the same type are to be used.

– Remove exhausted batteries from the Remote

Controller.

– Do not attempt to recharge non-rechargeable batteries.

– Do not use rechargeable batteries.

– Batteries are to be inserted with the correct polarity.

– The supply terminals are not to be short-circuited.

– Never throw batteries in a fire or attempt to open up its

outer casing.

– If the user does not intend to use the Remote Controller

for a long time, remove the batteries.

– Keep away from heat.

– The effect range of the Remote Controller is approximately

6m.

– Do not be subjected to strong shock.

– Do not be subjected to moisture.

If the unit gets moistured, wipe it off immediately.

– The Remote Controller operation may not function if the

projector’s IR sensors are exposed to direct sun light or

strong artificial light, or if there is an obstacle between

the IR sensors and the Remote Controller.

Preparing the Remote Controller

ENGLISH

VP-12S1

Adjust the vertical and

horizontal positions of the

projector.

Side view

Flat view

INSTALLATION

Recommended Setting

CAUTION

– For ceiling installation, consult with Marantz authorized dealer.

– Do not look into the lens when the projector is turned on.

It could damage your eyesight.

Horizontal center of the screen

Throw distance

Ceiling

Table Top

Ceiling Installation

Note : Lens shift position is at Full up.

SET UP PROCEDURES

ENGLISH

VP-12S1

40 inch

60 inch

80 inch

100 inch

120 inch

150 inch

200 inch

250 inch

/16 inch

1,281 mm

/16 inch

1,945 mm

102

/4 inch

2,609 mm

128

/8 inch

3,273 mm

155 inch

3,938 mm

194

/4 inch

4,934 mm

259

/8 inch

6,594 mm

325 inch

8,255 mm

Screen Size

(Diagonal)

16:9 screen

Throw distance

Minimum Maximum

Distance between the projector and the screen (throw distance)

Screen size

(Diagonal)

Throw distance

Screen

/16 inch

1,491 mm

89 inch

2,260 mm

119

/4 inch

3,029 mm

149

/16 inch

3,798 mm

179

/16 inch

4,568 mm

225

4 inch

5,721 mm

300

/16

inch

7,644 mm

376

/16 inch

9,567 mm

/4 inch

1,172 mm

inch

1,782 mm

/16 inch

2,392 mm

118

/16 inch

3,001 mm

142

/16 inch

3,611 mm

178

/16 inch

4,526 mm

238

/16 inch

6,050 mm

298

4 inch

7,575 mm

4:3 screen

Throw distance

Minimum Maximum

inch

1,365 mm

/16 inch

2,071 mm

109

/16 inch

2,777 mm

137

8 inch

3,483 mm

164

/16 inch

4,190 mm

206

/8 inch

5,249 mm

276

/16 inch

7,014 mm

345

/16 inch

8,780 mm

Note : Tolerance ±5 %

Minimum = 1

/16 x Screen size – 1

Maximum = 1

/2 x Screen size – 1

Unit : inch

Minimum = 33.21 x Screen size – 47.6

Maximum = 38.46 x Screen size – 47.6

Unit : mm

Minimum = 1

/16 x Screen size – 1

Maximum = 1

/8 x Screen size – 1

Unit : inch

Minimum = 30.49 x Screen size – 47.6

Maximum = 35.31 x Screen size – 47.6

Unit : mm

ENGLISH

You can adjust the image position with the Lens Shift knob.

Turn the Lens Shift knob to clockwise :

The image goes up.

• Maximum range to throw up :

Bottom of the image correspond to the center of the

Projection Lens.

Turn the Lens Shift knob to counterclockwise :

The image goes down.

• Maximum range to throw down :

Top of the image correspond to the center of the

Projection Lens.

Image Position Adjustment

Clockwise

Counterclockwise

Down

SET UP PROCEDURES

ENGLISH

When the projecting image is a trapezoid, correct it in

Keystone-V and/or Keystone-H in the Display Menu.

Keystone-V(Electronic vertical keystone correction)

Advanced Setting

Keystone-H(Electronic horizontal keystone correction)

Note : Electronic horizontal keystone correction works

properly when the lens shift position is at Full Up.

ENGLISH

• Press the ZOOM key, the NORMAL key or the FULL key on the remote controller for the 4:3 aspect ratio video source.

• Press the FULL key on the remote controller for 16:9 aspect ratio video source, such as 1080i, 1035i, and 720p video systems.

• Press the FULL key on the remote controller for the squeezed video source.

Full mode

The Screen Images in a Wide screen (16:9)

Original Source Image

4 : 3 video source

16 : 9 video source

The 16:9 squeezed image is displayed with the correct

aspect.

The 4:3 image is enlarged horizontally.

Normal mode

The picture with normal ratio 4:3 is displayed.

Zoom mode

The picture with normal ratio 4:3 is enlarged vertically

and horizontally (with same ratio) to the screen size

Through mode

Displays the image with the same resolution as the input video source except 1035i, 1080i, and XGA.

SET UP PROCEDURES

ENGLISH

• Press the ZOOM key, the NORMAL key or the FULL key on the remote controller for the 4:3 aspect ratio video source.

• Press the FULL key on the remote controller for 16:9 aspect ratio video source, such as 1080i, 1035i, and 720p video systems.

• Press the FULL key on the remote controller for the squeezed video source.

Full mode

The Screen Images in a 4:3 screen

Original Source Image

4 : 3 video source

16 : 9 video source

The 16:9 squeezed image is displayed with the correct

aspect.

The 4:3 image is enlarged horizontally.

Normal mode

The picture with normal ratio 4:3 is displayed.

Zoom mode

The picture with normal ratio 4:3 is enlarged vertically

and horizontally (with same ratio) to the screen size

Through mode

Displays the image with the same resolution as the input video source except 1035i, 1080i, and XGA.

ENGLISH

DVD

VCR

S-VIDEO OUT

VIDEO OUT

COMPONENT VIDEO OUT

Computer

HD Set Top Box

/ BS Tuner

RGB OUT

When making connections be sure to:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the plug properly. Any plugs that are not fully inserted often generate a noise.

When pulling out a cable:

• Be sure to grab the plug, not the cable itself.

CONNECTION

Connections with Video equipments

Connection with a HD-Video or PC

SET UP PROCEDURES

ENGLISH

Receiver equipment with

a Dolby Digital decoder

DIGITAL AUDIO IN

DV-SD OUT

DV camcoder

Connection with a DV camcoder

Note: DV IN connector is available for DV-SD format of i.LINK(IEEE1394).

Receiver equipment with

a Dolby Digital decoder

REMOTE CONTROL IN

REMOTE CONTROL OUT

External Controller

RS-232C

35mm Mini Plug (Mono)

Ferrite core

Control Adapter cable

Screen

Advanced connection

ENGLISH

1. Connect the supplied AC power cord.

The STANDBY indicator lights up and the projector

goes into the standby mode.

2. Press the POWER ON key on the remote controller or

the POWER key on the projector.

The POWER indicator lights up.

3. Press the FOCUS key on the remote controller to

display the FOCUS pattern and turn the Focus ring to

make an adjustment. Adjust the focus for the sharpest

image possible to obtain, using focus pattern.

Press the FOCUS key again to clear off the pattern.

4. Turn the Zoom ring to adjust the size of the image.

5. Switch on the equipment connected to the projector.

Press the INPUT SELECT key on the projector or the

COMPONENT key, S-VIDEO key, VIDEO key, or RGB

key on the remote controller.

1. Press the STANDBY key on the remote controller or the

POWER key on the projector.

2. The fan continues to run for a while to reduce internal

heat. The POWER ON indicator flashes in blue and no

key will be active minute. After about one minute

cooling has been provided, the unit turned off and the

STANDBY indicator lights up.

INITIAL SET UP

TO TURN OFF THE POWER

Page is loading ...

Marantz VP-12S1 User manual

Brand: Marantz

Model: VP-12S1

Category: Data projectors

Type: User manual

This manual is also suitable for

VP-12S1s

Download PDF

report

Marantz VP-12S1 User manual

This manual is also suitable for

Marantz VP-12S1 User manual

Related papers

Other documents