2. Home
  3. Domestic appliances
  4. Large home appliances
  5. Fridges
  6. Liebherr
  7. ECBN5066RH

Liebherr ECBN5066RH Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Liebherr ECBN5066RH Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
7083 137-00
ECBN 5066
GB
Installation instructions
for NoFrost combined refrigerator-freezers Page 14
14
Setting up
•Avoidpositioningtheapplianceindirectsunlightornearcook-
ers,radiatorsandsimilarsourcesofheat.
•Theflooronwhichtheappliancestandsshouldbehorizontal
andlevel.
•Theventilationgrillesshouldnotbeobstructed.Alwaysensure
thatthereisgoodventilationandthattheoutwardflowingairis
abletoescape.
• StandardEN378specifiesthattheroominwhichyouinstall
yourappliancemusthaveavolumeof1m³per8gofR600a
refrigerantusedintheappliance,soastoavoidtheformationof
inflammablegas/airmixturesintheroomwheretheappliance
islocatedintheeventofaleakintherefrigerantcircuit.The
quantityofrefrigerantusedinyourapplianceisindicatedon
thetypeplateontheinsideoftheappliance.
Appliance venting
Therequiredairflowisdirected
throughtheplinth.
Itisimportanttousetheprovided
ventilationgrillefortheventila-
tionopening.
Thisopeningmustnotbecov-
ered.
Electrical connection
Onlyoperatetheappliancewithalternating current (AC).
Thepermissiblevoltageandfrequencyareindicatedonthetype
plate.Thepositionofthetypeplateisshowninthesectionentitled
Description of the appliance(intheoperatinginstructions).
Thesocketmustbeproperlyearthedandprotectedbyafuse.
Thetrippingcurrentofthefusemustbebetween10Aand16A.
Donotconnecttheapplianceusinganexten-
sioncableorextensionsocket.
Donotusestand-aloneinverters(conversion
of direct current to alternating/three-phase
current)orenergy-savingplugs.Riskofdam-
agetotheelectroniccontrolsystem!
Door swing clearance
Please allowfordoorswingclear-
anceatlocationsnexttoawall.
The illustrated measurement is
withoutmounteddoorpanel.
Besuretoaddyourpanelthickness
andhandledepthtothismeasure-
mentinordertoavoidinterferences.
15
Appliance dimensions
A=76mm
B=2027mm
C=757mm
D=610mm
E=1413mm
F=952mm
Installation dimensions
Thistype ofdimension
lineindicatestheheight
measuredfromthefloor.
GB
Theicemakerisfittedinthefreezercompartmentofthecom-
bined refrigerator-freezer. It must be connected to the mains
watersupplytowork.
The water shut-offvalve must be positioned withintheareas
markedingrey.
Important
Donotinstalltheshut-offvalvebehindtheappliance.
WARNING!
The water shut-o valve must not be posi-
tioned directly above the socket!
The gap between the water shut-o valve and
the socket must comply with the regulations
of the country in which the appliance is used!
1Inthisarea,thepowercordcomesoutoftheappliancerear.
Freelengthofthepowercord=2500 mm
Choosethepositionofthesocketconsideringthesespeci-
fications.
Thesocketmustnotbesituatedbehindthe
applianceandmustbeeasilyaccessible.
16
Mounting the anti-tipping device
WARNING!
The supplied anti-tipping bracket must be in-
stalled in all cases. This prevents the appliance
from tipping over when the fully loaded door is
opened.
Installation
1. Markthecentrelineoftheapplianceonthefloor.
Aligntheanti-tippingbracketcentretothecentreline.
CAUTION!
Ensure that there are no electric cables or water
pipes in the wall section to which the anti-tipping
bracket is to be secured. These could be damaged
during installation.
2. Secure the anti-tipping bracket. See section entitled "Anti-
tipping device mounting options".
Important!
If the floor slopes down sideways, the anti-tipping
bracket must be fitted horizontally. Lay down spacers
in the appropriate positions.
Wall
Floor
Anti-tipping device mounting options
Wall
Floor
Securingtothewallusing3screws.
Whensecuringtheanti-tippingdevicetocon-
cretewalls,usesuitableplugs.
The screws (6 x 60) are
includedintheaccessory
pack.
Securingtothefloorusing3screws.
Whensecuringtheanti-tippingdevicetoaconcrete
floor,usesuitableplugs.
17
3.
4.
Connection to the water supply
Safety instructions and warnings
•Donotconnecttothewatersupplywhilethecombinedrefrig-
erator-freezerisconnectedtotheelectricitysupply.
• The connection to the mains water supply may only be
made by trained personnel.
• The water quality must comply with the drinking water
directives of the country in which the appliance is used.
•Theicemakerisdesignedexclusivelytomakeicecubesin
quantitiesrequiredbyahouseholdandmayonlybeoperated
withwatersuitableforthispurpose.
• Allrepairsandworkontheicemakermayonlybecarriedout
bycustomerservicepersonnelorothertrainedpersonnel.
• The manufacturer cannot accept liability for damage
caused by a faulty connection to the mains water supply.
Water pressure
The water pressure must be between 0.15 and 0.6 MPa
(1.5 - 6 bar).
Important!
Ifthewaterfilterisinsertedintheappliance,thewater
pressuremustliebetween0.3 and 0.6 MPa (3 - 6 bar).
Ifthewaterpressurewiththeinsertedwaterfilteristoo
low,thismaycausetheicemakertomalfunction.
Thewatersupplytotheappli-
ancemustbethroughacold
waterpipethatcanwithstand
the operating pressure and
complies with the hygiene
regulations.
Forthis,usethestainlesssteelhosesupplied(length3m).
2.
GB
Installing the appliance
1. Placetheapplianceinfrontoftheinstallationrecess.
2. Applycoverstripsabove,be-
tweenandbelowthesecuring
platesonthesidewallsofthe
appliance.
• Cutthecoverstripstotheright
lengthforthispurpose.
• Fittheadhesivecoverstrips
leavingagapof6mmtoeach
securingplate.
3. Insert the bent section of the hose
throughtheopeningattherightside
oftheappliance.
4. Connect the hose to the solenoid
valvea t t h e f r o n tsi d eoftheappliance.
18
6. Routethemainscabletowardsthesocket.
7. Routethewaterhosetowardsthewatershut-offvalve.
WARNING!
Do not connect the appliance to the power supply
until the installation has been completed.
CAUTION!
Lay the mains cable and the water hose in such
a way that they will not be damaged when the
appliance is slid into the installation recess.
6.
7.
Important!
Aftertheicemakerhasbeenswitchedon,thewater
supplysystemmustbebled.SeethesectionBleeding
the ice makerintheoperatinginstructions.
8.
5.
5. Locatethewaterhoseintotherailof
theapplianceplinth.
8. Pushtheapplianceslowlyintotherecesssothattheappliance
plinthengagesintheanti-tippingbracket.
9. Fillthehosewithwaterandconnecttotheshut-off
valve.
 Opentheshut-offvalveandcheckthesystemfor
leakage.
19
Adjusting the refrigerator door
Thelateraltiltoftherefrigeratordoorcanbeadjustedifrequired.
Undoscrews
1
.Adjustthelateraltiltusingthegrubscrew
2
(AllenkeyA/F2.5).
Adjusting the front of the drawer
Ifrequired,thefrontofthefreezerdrawerscanbeadjusted.
Transferthescrewsshownintheillustration(ontheleft-and
right-handsidesofthefreezerdrawer)individuallytothelong
slotsbelow.
Tightenthescrewsoncethefrontofthedrawerisintheright
position.
Side view of the freezer
drawer pulled out
GB
Levelling the appliance
1. Adjusttheheightoftheapplianceatthefrontbytwistingthe
adjustablefeet
1
.Usethespannerprovided.
Turnthespanneranticlockwisetoraisetheappliancefront
andclockwisetolowerit.
 Positionthespanneraccordingly(
1
).
2. Adjusttheheightoftheapplianceattherearbyturningthe
adjustingbolts
2
.
Fastening the appliance in the recess
Onceintherecess,securetheappliancetothebodyoftheunit
usingthesecuringplates(4x16screws).
Then click the covers supplied into
place.
20
5.
4. Thefrontedgeofthebrackets
is flush with the front of the
ventilationgrille.
 Adjustthesupportsaccordingly.
2.
7.
4.
6.
1.
3.
Mounting the ventilation grille
 Pulloutthebottomfreezerdrawer.
1. Remove the protective film from the dust filter.
Insertthefilteratthebottom,pressthebutton
downandclickthefilterintoplace.
2.Remove the locking pins of
bothsupports.Thesupports
are provided with the appli-
anceaccessorypack.
3.Insertthesupportsfortheventilationgrille
ontheleftandrightsidesinthemotor
compartment.
5.Insertthelockingpinstoblockthesup-
ports.
6. Installtheventilationgrille.
 Thegrillehasboltsontheinside(seedetailintheillustration
below).Theseboltsmustbeinsertedintotheholesofthe
supports.
7. Adjusttheheightoftheventilationgrille.
• Loosenthegrubscrewsatthefrontofthegrille(Allenkey
A/F2.5).
• Adjusttheventilationgrilletothedesiredheight.
• Tightenthegrubscrews.
21
Panel dimensions
Min.panelthickness=16mm
Max.panelthickness=19mm
Maximum panel weight
Refrigeratorpanel=27kg
Freezerdrawerpanel=10kg
Removing the mounting accessories from the
refrigerator door
Removethecover
1
andunscrewthetopandbottomattach-
mentbrackets
2
fromtherefrigeratordoor.Theseattachment
bracketswillbemountedontotherefrigeratordoorpanel.
Important!
The securing nuts are needed for re-mounting the pre-
assembled door panel onto the refrigerator door.
Removing the mounting accessories from the
freezer drawers
Unscrewtheattachmentbrackets
3
fromthefreezerdrawers.
These attachment brackets will be mounted onto the freezer
panels.
Important!
The screws are needed for re-mounting the pre-assembled
freezer panels onto the freezer drawers.
GB
Important!
To avoid collisions when opening the refrigerator
door, the lateral distance between the door and
the panels must be at least 6 mm.
22
Mounting the attachment brackets onto the door panels
1. Drawaline1041mmfromthebottomedgeofthedoorpanel.
2. Drawafurtherline107.5mmfromthebottomedgeofthedoorpanel.
3. Alignoneoftherefrigeratordoorattachmentbracketstothetopline,asshownintheillustrationbelow,andsecurewithatleast
6screws(4x14).
4. Alignthesecondrefrigeratordoorattachmentbrackettothebottomline,asshownintheillustrationbelow,andsecurewithat
least6screws(4x14).
5. Secureeachoftheattachmentbracketsthathavebeenremovedfromthefreezerdrawersusing3screws(4x14),asshownin
theillustrationbelow.
23
fig. D
Mounting the refrigerator panel
fig. A
fig. B
fig. C
1. Screwintheadjustingpinsontheundersideoftherefrigerator
doorcompletely(fig. A).
2. Opentherefrigeratordoorandsuspendtherefrigeratorpanel
onthetopadjustingpins(fig. B).
3. Screwsecuringnutsontotheadjustingpinsandslightlytighten.
4. Closetherefrigeratordoorandchecktheheightofthepanel.
5. Adjusttheheightofthepanelifnecessary.Undothesecuring
nutsandusetheadjustingpinstoadjust(fig. C).
6. Adjustthepanelhorizontally(usingthelongslotsintheat-
tachmentbracket)(fig. D).
7. Tightenthesecuringnuts.
GB
24
fig. E
fig. F
8. Unscrewtheadjustingpins(bottomoftherefrigeratordoor)
untilthesetouchtheattachmentbracket(fig. E).
9. Screwonthesecuringnutsandtighten(fig. F).
11. Clickthetopandbottomcovers
1intoplace(fig. H).
Insertthecoverstripprovided2betweenrefrigeratordoor
andpanel.
fig. H
fig. G
10. Undothethreescrewsonthetopoftheattachmentbracket,
adjustthedoorpanelasillustratedinfig. Gandthenretighten
thescrews.Thesameprocedurecanbecarriedoutforthe
bottomattachmentbracket.
25
Mounting the freezer panels
1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled
panel.
Thesamescrewsmustbeusedasthoseusedtoscrewon
theattachmentbrackets (see section entitled "Removing
the mounting accessories from the freezer drawers").
2. Closethefreezerdrawerandcheckthepositionofthepanel.
Adjusttheheightofthepanelbyundoingtheleftandright
screws.Tightenthescrews.
3.Pulloutthebottomfreezerdrawerandmountthepanelinthe
sameway.
4. Forbothdrawers,coverthegapbetweenthedrawerandthe
panelwiththecoverstripssupplied.Removetheprotective
filmfromthestripandinsertintothegapatthetop.
3.5x13mm
Changing over door hinges
Doorhingesmayonlybechangedbyatrainedexpert.
WARNING!
Do not try to change over the door hinges your-
self. The refrigerator door hinges are fitted with
strong closing springs. If the hinge accidentally
snaps shut, this can lead to serious injury.
GB
/