Cooper T –Series Owner's manual

Brand: Cooper

Model: T –Series

Category: Above ground pool accessories

Type: Owner's manual

Cooper T –Series is a versatile above-ground pool pump designed to provide reliable and efficient water circulation for your swimming pool. With its durable construction and advanced features, the T-Series pump is built to handle the demands of any above-ground pool, ensuring crystal-clear and refreshing water all season long.

The T-Series pump is equipped with a powerful motor that delivers exceptional water flow rates, ensuring that your pool water is thoroughly filtered and sanitized. The pump's advanced impeller design minimizes energy consumption while maximizing performance, providing you with both efficiency and savings.

www.cooperpool.com

877-903-POOL

T –Series

Above - Ground

ool Pump

U.S. Version

Canadian Version

Owners

Manual

ATTENTION

READ SAFETY INSTRUCTIONS

PRIOR TO ASSEMBLY OR

OPERATION OF PUMPS

* To avoid dangerous or fatal electric shock, turn OFF power to motor before working on

electrical connections.

* Connect to a circuit protected by a class “A” ground fault circuit interrupter.

* GFCI tripping indicates an electrical problem. If GFCI trips and will not reset, have a

qualified electrician inspect and repair electrical system.

* Exactly match supply voltage to nameplate voltage (115 volt single phase). Incorrect

voltage can cause fire or damage motor and voids warranty

Made in Canada

Pool Safety

Your swimming pool will no doubt be a source of

fun, exercise and relaxation for you and your

family. To further enjoy your pool the following is a

list of Safety Tips to remind your family and

friends.

1. Install a safety enclosure around your pool with a self-

closing, self-locking gate.

2. Do not leave children unattended. Supervise children

at all times when they are in or around the pool

enclosure.

3. Rescue equipment such as life rings, life hooks and

first aid kit are recommended.

4. Learn CPR procedures, it can save lives.

5. Teach children to swim, it will be a life long benefit.

6. Never swim alone, even good swimmers need help

occasionally.

7. Do not swim in poor lighting conditions or if the pool

is too cloudy to see the bottom.

8. Store chemicals safely and keep secured.

9. Keep electrical equipment and moving equipment

away from children.

Electrical Safety

1. Turn off all electrical equipment before servicing pool

equipment.

2. Have your electrical system checked by a professional

to insure compliance with all electrical codes.

3. Do not swim if there is a possibility of lightning.

4. Do not allow electrical appliances such as radios or

lamps within 10’ of the pool.

5. Do not install electrical switches in a location that

requires you to reach over pool equipment.

6. If you feel a tingling sensation in or near the pool,

shut off the power to the pool equipment and call a

professional to check out your system.

7. It is recommended all pool pumps should be

connected to a Ground Fault Circuit Interrupter.

8. All electrical equipment should be properly grounded.

Maintenance & Service Safety

1. Maintain all pool equipment in good working

order.

2. Check your equipment for air leaks by examining

the return water for excessive air bubbles.

3. Always stand clear of the filter when starting up

as the tanks expand under pressure.

4. Position pressure gauges and valves in a location

where they can be easily visible.

5. If you have any concerns about your pool,

equipment or systems contact your pool

professional dealer or the original equipment

manufacturer.

Safety Instructions

1. Do not connect pumps to a high-pressure system

or city water supply.

2. Have a trained professional perform all pressure

tests.

3. Since pumps and associated equipment are

pressurized insure all air is out of system prior to

testing.

4. Do not allow children to use the products unless

supervised at all times.

5. To prevent flooding, all systems installed below

water level require isolating valves.

6. To guard against entrapment use only non-

entrapment fittings or double suction.

7. Always disconnect power supply prior to making

any electrical connections or servicing of pump.

8. Pump must be permanently connected to circuit,

no other lights or appliances should be on the same

circuit.

9. Pump motor must be permanently grounded

electrically.

!!!!! Use this pump only as described in this

manual. Any other use not recommended by the

manufacturer may cause electric shock, damage

to property, or injury.

Pump Priming and Start-Up

1. Remove pump strainer lid and fill strainer with water

and replace lid.

2. Open all suction and discharge valves and air bleed (if

standard with filter).

3. Start pump and unit should prime within 2-3

minutes(dependant upon distance pump is from pool and

suction lift). Repeat priming procedure and if priming

does not occur, refer to trouble shooting section.

4. The strainer basket should be periodically removed

and cleaned of any debris collected. Do not operate

pump without basket in place.

Installation Tips

1. Mount pump on a solid and level base to avoid

vibration and piping stress.

2. Install pump as close to water level as possible as

excessive lift conditions(should not exceed 5’) increases

priming time and increases friction loss.

3. Pump should be located as close to pool as practical.

4. If installed indoors or in a mechanical room, be sure

to allow for proper drainage to prevent risk of flooding.

5. Pump should be protected from excessive heat,

moisture and dust to insure longer motor life.

6. Pump motors require adequate ventilation for cooling

purposes, avoid any secondary enclosures.

7. Piping sizes should be equal to the diameter of pump

openings or greater, dependent upon distance from pool

to pump.

8. Allow sufficient access for servicing pump and

associated plumbing.

9. Insure that the electrical supply agrees with the motor

voltage, phase and that the wire size is adequate for the

horsepower rating and distance from the power source.

Electrical circuits must be protected in accordance

with local electrical codes.

10. Never operate pump without water as water acts as a

coolant and lubricant for the mechanical shaft seal.

11. To avoid air lock, slope piping slightly upward to

pump suction.

12. Avoid any strain on pump. Support both influent and

effluent piping and guard against piping misalignment.

Trouble Shooting

Pump will not prime.

1. No water in strainer.

2. Strainer pot lid is not tight.

3. Strainer lid “O” ring is damaged or not positioned

correctly.

4. Water level below wall skimmer opening.

5. Strainer basket clogged.

6. Valve not open in system.

7. Air leak in suction piping.

Low flow, high filter pressure reading.

1. Filter is dirty, requires backwash.

2. Restricted return line.

Low flow, low filter pressure.

1. Pump strainer or skimmer basket clogged.

2. Pump impeller clogged.

3. Suction air leak.

4. Obstruction in suction line.

Motor does not turn.

1. Motor switch off.

2. Circuit breaker tripped.

3. Motor terminals incorrect.

4. Motor bearing problem.

5. Impeller “jammed” with debris.

Motor over heats and cuts out motor.

1. Electrical supply connections incorrect.

2. Pump motor wiring undersized.

3. Low voltage condition.

4. Poor motor ventilation.

Save these

instructions

for future

reference

No.

6***

11*

12*

13*

15*

15**

16**

17*

* Used On Pumps Sold In Canada Only.

** Used On Pumps Sold In USA Only.

*** not used after 2002

Part No. Description

---- Motor, Specify HP, Voltage, and Speed.

7012 Volute

7200 Seal Kit

7002 3/4hp Impeller

7003 1hp Impeller

7004 1 1/2hp Impeller

7005 2hp Impeller

7015 Volute O-Ring

7013 Wear Ring

7017 Suction Cover

7018 Screw 8-32 x 5/8" Plated

7019 Screw 8-32 x 5/8" S.S.

7016 Drain Plug O-Ring

7014 Drain Plug 1/4"

7041 Motor Cover

7042 Motor Cover End Cap

7225 25' Cord Set

7020 On Off Toggle Switch

7021 2 Speed Toggle Switch

7237 Strain Releif Bushing

7323 Strain Releif Bushing 3/4"

7022 Rubber Cover For Toggle Switch (Not Shown)

7203 3' Cord Set

7043 Insulation Strip For # 7041 (Not Shown)

No.

Part No. Description

6571 Strainer Body

6573 Union O-Ring

6576 Strainer Lock Ring

6574 Strainer Lid

6575 Strainer O-Ring

6572 Strainer Debris Basket

6569 Drain Plug & O-Ring ( Not Shown )

Save these instructions for

future reference

LIMITED WARRANTY

To original purchasers of its Filter and pump equipment, W. Cooper Inc., warrants its product to be free of defect in material and workmanship

for a period of one year from date of purchase.

Equipment which fails or is defective during warranty period, except as a result of freezing, accident, negligence, improper installation , or dry

run, shall be repaired or replaced at our option without charge within 90 days of defective product.

In order to obtain warranty replacements or repair, defective products should be returned, transportation paid, to the place of purchase, or the

nearest authorized “Cooper” service center.

No return may be made directly to the factory without express written authorization of W. Cooper Inc.

Some provinces or states do not allow a limitation on the duration of implied warranty, or the exclusion or limitation of incidental

consequential damages, so the above limitation or exclusion may not apply.

This warranty gives you specific legal rig

hts, and you may also have other rights which could vary from province to province or state to state.

Cooper T –Series Owner's manual

Brand: Cooper

Model: T –Series

Category: Above ground pool accessories

Type: Owner's manual

Download PDF

report

Cooper T –Series Owner's manual

Cooper T –Series Owner's manual

Other documents