Black & Decker EMAX38 T3 Owner's manual

Page is loading ...

2

ENGLISH

(Original instructions)

Intended use

Your Black & Decker mower has been designed for mowing

grass. This tool is intended for consumer use only.

Warning! Read all of the 'Safety, Maintenance,

Service' manual carefully before operating

this appliance.

Read all of this manual carefully before operating

the appliance.

Features

This appliance includes some or all of the following features.

1. Switch box

2. On/off switch

3. Upper handle

4. Intelligent cable management

5. Lower handle

6. Cable storage holders

7. Height adjustment

8. Height of cut gauge

9. EdgeMax

10. Grass collection box

11. Clear grass ap

12. Carry handles

Assembly

Warning! Before assembly, make sure that the appliance is

switched off and unplugged.

Assembling the grass collection box (g. A - D)

The grass box requires assembly before use and comes in 5

pieces.

u Clip the handle (13) into the lid (14) of the grass box (g.

A). The handle will only t one way round.

u Clip the 2 sides (15) of the grass collection box together.

Make sure that all clips and guides are aligned (g. B).

u Align the assembled sides onto the bottom (16) of the

grass collection box. Ensure that the 4 guides (17) are

aligned (g. C)

u Push the 2 parts together. Apply even force around all

edges of the grass collection box securing the clips

into position uniformly. Check that each clip is fastened

together securely.

u Align the lid (14) onto the assembled grass collection box.

Ensure that the 10 guides (18) are aligned (g. D)

Note: Take extra care when aligning the 2 clips at the rear of

the grass collection box.

u Push down on the lid to secure all clips. Begin at the back

and ensure that all clips are securely located.

Fitting the lower handle (g. E)

u Insert the ends of the lower handle (5) into the corre-

sponding holes in the mower.

u Press the handle down as far as it will go.

u Secure the handle using the screws (19.

Assembling the upper handle (g. F)

u Fit the upper handle part (3) to the lower handle (5) using

the knobs (20), washers (21) and screws (22) as shown.

Note: The upper handle can be xed in 2 different height

positions.

Securing the motor cable (g. G)

The motor cable has to be xed using the cable restraints.

u Clip the cable to the upper and lower handle using the

restraint clips (23) as shown.

Fitting the grass collection box (g. N)

u Lift the clear grass ap (11) and place the grass collection

box (10) over the lugs (24).

Replacing the blade (g. L)

Warning! Ensure the blade has completely stopped and

disconnect the appliance from the mains.

Warning! Only use the specied replacement blade.

Warning! Use heavy-duty gloves to grip the blade.

To remove the blade:

u Turn the appliance onto its side.

u Using heavy-duty gloves, grip the blade.

u Use a 13mm spanner to loosen and remove the blade bolt

(25) by turning the spanner anti-clockwise (ac).

u Remove the blade (26) and blade bolt (25).

To replace the blade:

u Offer the blade up to bolt shaft and locate the blade bolt

(25) into the bolt shaft.

Note: When tting a blade, the text on the blade must be

facing the user.

u Tighten the blade bolt (25) as rmly as possible by hand.

u Using heavy-duty gloves, grip the blade.

u Use a 13mm spanner to securely tighten the blade bolt

(25) by turning the spanner clockwise (c).

Use

Warning! Let the appliance work at its own pace. Do not

overload.

Adjusting the height of cut (g. M1 & M2)

The height of cut is adjusted by the central height adjust

mechanism, there are 6 positions to choose from.

To set the height of cut

u Pull the height adjustment lever (7) away from the body of

the unit.

3

ENGLISH

(Original instructions)

u Move the lever towards the rear of the appliance to lower

the height of cut.

u Move the lever towards the front of the appliance to raise

the height of cut.

u Push the height adjustment lever (7) into one of the 6

height locations.

Note: The height of cut can be viewed on the height of cut

gauge (8) on the side of the unit.

Switching on and off (g. I)

Switching on

u Push in and hold the lock-off button (27).

u Pull the on/off switch (2) towards the handle.

u Release the lock-off button.

Switching off

u Release the on/off switch (2).

Warning: Never attempt to lock a switch in the on position.

Mowing (g. P1 & P2) (EMax38i, EMax42i &

EMax42ri only)

We recommend to use your mower as outlined in this section

in order to achieve optimum results and to reduce the risk of

cutting the mains cable.

u Loop the mains cable through the intelligent cable

management system (4) as shown (g. H) ensue that you

leave approximately 100 cm of cable between the switch-

box (1) and the intelligent cable management restraint (4).

u Ensure that the cable restraint can slide freely from one

handle to the other.

u Place the bulk of the mains cable on the lawn, close to the

starting point (position 1 in g. P1).

u Switch the appliance on as described above.

u Proceed as shown in g. P1

u Move from position 1 to position 2.

u Turn right, stepping over the cable and proceed towards

position 3. The cable restraint will slide from one side of

the handle to the other ensuring that the cable is laid out

away from the cutting blade.

u Turn left, stepping over the cable and move towards posi-

tion 4. The cable restraint will slide from one side of the

handle to the other ensuring that the cable is laid out away

from the cutting blade.

u Repeat the above procedure as required.

Warning: Do not work towards the cable as shown in g. P2.

Mowing (g. P1 & P2)(EMax34s & EMax34i only)

We recommend to use your mower as outlined in this section

in order to achieve optimum results and to reduce the risk of

cutting the mains cable.

u Place the bulk of the mains cable on the lawn, close to the

starting point (position 1 in g. P1).

u Switch the appliance on as described above.

u Proceed as shown in g. P1

u Move from position 1 to position 2.

u Turn right and proceed towards position 3.

u Turn left and move towards position 4.

u Repeat the above procedure as required.

Warning: Do not work towards the cable as shown in g. P2.

EdgeMax (g. K1 & K2)

EdgeMax allows you to cut grass right up to the edge of a wall

or fence (g K1).

EdgeMax allows you to accurately cut grass right up to the

edge of your lawn (g K2).

u With the lawnmower parallel with the edge of your lawn.

u Push the lawnmower along the edge of the lawn. Ensure

that the EdgeMax (9) is slightly over the edge of your lawn

(g.K2)

Compact&Go (g. J) (EMax34i, EMax38i, EMax42i &

EMax42ri only)

When the grass collection box is full you can compact the

grass in the collection box. You can determine how full the

grass collection box is by looking through the clear grass ap

(11).

u Release the on/off switch (2).

u Using your right foot, press the grass compaction lever

(29) all the way down until it locks into place.

Note: The grass in the collection box is now compressed into

the rear of the box. You may continue mowing until the grass

collection box becomes full.

Emptying the grass collection box (g. J) (EMax34i,

EMax38i, EMax42i & EMax42ri only)

u Release the on/off switch (2).

u Remove the grass collection box (10).

u Empty the contents from the front of the box.

u Place the grass collection box on the ground and pull in

and hold the grass compaction lever release button (30).

u Lift the grass compaction lever (29) into the vertical

position and release the grass compaction lever release

button (30).

u Empty the contents from the rear of the box.

Emptying the grass collection box (EMax34s only)

When the grass collection box is full you should empty the

grass in the collection box.

u Release the on/off switch (2).

u Remove the grass collection box (10).

u Empty the contents from the box.

4

ENGLISH

(Original instructions)

Cable storage (g. O)

The cable holders (6) provide a safe and convenient way to

store the cable (31) when not in use.

u Wrap the cable around the cable holders (6) in a gure of

eight pattern.

Carrying the mower

Warning! Ensure the blade has completely stopped and

disconnect the appliance from the mains.

u The mower can be carried using the convenient carry

handles (12).

Hints for optimum use

u If the grass is longer than approximately 10 cm, make two

cuts to obtain a better nish. First mow at maximum height

of cut, then use a low or medium height of cut.

u In order to achieve optimum results, only mow dry grass.

Troubleshooting

If your appliance seems not to operate properly, follow the

instructions below. If this does not solve the problem, please

contact your local Black & Decker repair agent.

Warning! Before proceeding, remove the plug from the

socket.

Problem Possible Cause Possible solution

Machine fails to

operate

Power turned off Turn power on

Fuse faulty/blown Replace fuse

Grass too long

Increase the height of

cut and move machine

to shorter grass to start

Thermal cut out

activated

Allow motor to cool and

increase height of cut

Machine functions

intermittently

Thermal cut out

activated

Allow motor to cool and

increase height of cut

Machine leaves

ragged nish or

motor labours

Height of cut too low Increase height of cut

Cutting blade blunt Replace the blade

Underside of machine

clogged

Check underneath the

machine and clear out

as necessary (always

wear heavy duty

gloves)

Blade tted upside

down

Ret blade correctly

Technical data

EMax34s

EMax34i

EMax38i EMax42i

EMax42ri

Voltage

V

AC

230-240 230-240 230-240

Power Input

W

1400 1600 1800

No-Load Speed

min

-1

3500 3500 3500

Height adjustment

mm

20-70 20-70 20-70

Blade length

mm

340 380 420

Weight

kg

12.1 13.3 13.9

Hand/arm weighted vibration value according to EN60335:

= 3.2 m/s

2

, uncertainty (K) = 1.5 m/s

2

.

Type 3

5

ENGLISH

(Original instructions)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

%

EMax34s / EMax34i / EMax38i / EMax42i / EMax42ri

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1, EN 60335-2-77

2000/14/EC, Lawn Mower, L < 50cm, Annex VI,

Netherlands

Level of sound power according to 2000/14/EC

(Article 12, Annex III, L ≤ 50 cm):

L

WA

(measured sound power) 93 dB(A)

uncertainty (K) = 3 dB(A)

L

WA

(guaranteed sound power) 96 dB(A)

uncertainty (K) = 3 dB(A)

These products also comply with directive

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

04/12/2012

2004/108/EC and 2011/65/EU.

Page is loading ...

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/pro-

ductregistration or send your name, surname and product code to

Black & Decker in your country

.

DEUTSCH

Vergessen Sie nicht, Ihr Produkt registrieren zu lassen!

www.blackanddecker.de/productregistration

Lassen Sie Ihr Produkt unter www.blackanddecker.de/productreg-

istration online registrieren oder schicken Sie Ihren Nachnamen,

Vornamen und den Produktcode an Black & Decker in Ihrem Land.

FRANÇAIS

N’oubliez pas d’enregistrer votre produit !

www.blackanddecker.fr/productregistration

Enregistrez votre produit en ligne sur www.blackanddecker.fr/

productregistration ou envoyez vos nom, prénom et code produit à

Black & Decker dans votre pays.

ITALIANO

Non dimenticate di registrare il prodotto!

www.blackanddecker.it/productregistration

Registrate il prodotto online su www.blackanddecker.it/productreg-

istration o inviate nome, cognome e codice del prodotto al centro

Black & Decker del vostro paese.

NEDERLANDS

Vergeet niet uw product te registreren!

www.blackanddecker.nl/productregistration

U kunt uw product online registreren op www.blackanddecker.nl/pro-

ductregistration of u kunt uw voornaam, achternaam en productcode

opsturen naar Black & Decker in uw land.

ESPAÑOL

¡No olvide registrar su producto!

www.blackanddecker.es/productregistration

Registre su producto on-line en www.blackanddecker.es/produc-

tregistration o envíe su nombre, apellidos y código de producto a

Black & Decker en su país.

PORTUGUÊS

Não se esqueça de registar o seu produto!

www.blackanddecker.pt/productregistration

Registe o seu produto online em www.blackanddecker.pt/productre-

gistration ou envie o seu nome, apelido e código do produto para a

Black & Decker no seu país.

SVENSKA

Glöm inte att registrera produkten!

www.blackanddecker.se/productregistration

Registrera produkten online på www.blackanddecker.se/productre-

gistration

eller skicka namn och produktkod till Black & Decker i landet

du bor i.

NORSK

Ikke glem å registrere produktet ditt!

www.blackanddecker.no/productregistration

Registrer produktet ditt online på www.blackanddecker.no/pro-

ductregistration, eller send ditt navn, etternavn og produktkode til

Black & Decker i ditt eget land.

DANSK

Glem ikke at registrere dit produkt!

www.blackanddecker.dk/productregistration

Registrer dit produkt på internettet på: www.blackanddecker.dk/

productregistration eller send dit navn, efternavn og produktkode til

Black & Decker i dit eget land.

SUOMI

Muistathan rekisteröidä tuotteesi!

www.blackanddecker./productregistration

Rekisteröi tuotteesi verkossa osoitteessa www.blackanddecker./

productregistration tai lähetä etunimesi, sukunimesi ja tuotekoodi

oman maasi Black & Decker -edustajalle.

Ε Λ Λ Η Ν Ι Κ Α

Μην ξεχάσετε να καταχωρίσετε το προϊόν σας!

www.blackanddecker.gr/productregistration

Καταχωρίστε το προϊόν σας σε σύνδεση στη σελίδα www.

blackanddecker.gr/productregistration ή στείλτε το όνομα, επίθετο

σας και τον κωδικό πριονωτός στη Black & Decker στη χώρα σας.

Page is loading ...

Black & Decker EMAX38 T3 Owner's manual

This manual is also suitable for

Black & Decker EMAX38 T3 Owner's manual

in other languages

Related papers

Other documents