Gorenje NRK6192JBK User manual

EN

DETAILED

INSTRUCTIONS FOR

USE OF UPRIGHT

REFRIGERATOR AND

FREEZER

www.gorenje.comwww.gorenje.com

2

413758

We thank you for the

confidence you have shown by

purchasing our appliance.

We wish you find a lot of pleasure in its

use.

The appliance is intended solely for

household use.

Refrigerator freezer (hereinafter: the

appliance) consists of two parts: the

upper part is the refrigerator and the

lower part is the freezer.

The refrigerator is intended for storing

fresh food at temperatures above 0°C.

The freezer is intended for freezing fresh

food and for long-term storage of frozen

food (up to one year, depending on the

type of food).

3

TABLE OF CONTENTS

413758

INTRODUCTION

APPLIANCE

DESCRIPTION

DEFROSTING

AND CLEANING

THE APPLIANCE

4 IMPORTANT NOTES AND WARNINGS

8 ADVICE FOR SAVING POWER WITH REFRIGERATION

APPLIANCES

9 APPLIANCE DESCRIPTION

10 INSTALLATION AND CONNECTION

12 CHANGING THE DIRECTION OF DOOR OPENING

16 OPERATING THE APPLIANCE WITH MECHANIC CONTROLS

18 APPLIANCE WITH ELECTRONIC CONTROL

29 APPLIANCE INTERIOR EQUIPMENT

34 RECOMMENDED DISTRIBUTION OF FOOD IN THE APPLIANCE

35 STORING FOOD IN THE REFRIGERATOR

36 STORING FOOD IN THE FRESHZONE DRAWER

37 STORING FOOD IN THE ZEROZONE DRAWER

39 FREEZING AND STORING FROZEN FOOD

39 Freezing process

40 Important warnings on freezing fresh food

40 Storage˛of industrially frozen food

41 Frozen food storage time

41 Defrosting frozen food

42 DEFROSTING THE APPLIANCE

43 CLEANING THE APPLIANCE

44 TROUBLESHOOTING

46 INFORMATION ABOUT APPLIANCE NOISE

OTHER

STORING AND

FREEZING FOOD

4

IMPORTANT

NOTES AND WARNINGS

413758

This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or metal capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe

way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by

children without supervision.

Before connecting the appliance to the power mains,

please read carefully the instructions for use which

describe the appliance and its correct and safe use. The

instructions apply for several appliance types/models;

thus, settings or equipment may be described herein

which is not available in your appliance. The instruction

manual includes the NO FROST version/model of

the freezer which is fitted with a fan and in which the

defrosting process is automatic.

Remove the packaging intended for protecting the

appliance or particular parts during transport.

Spacers are fitted on the

corners of the doors.

Remove them and insert

the supplied plugs into

their slots (only in some

models).

5

413758

Before connecting the appliance to the power

mains, let the appliance rest in a vertical position for

approximately 2 hours. This will reduce the possibility

of operation faults due to the effect of transport on the

cooling system.

The appliance must be connected to the power

mains and grounded in compliance with the effective

standards and regulations.

The appliance may not be used outdoors and it may

not be exposed to rain.

Do not store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

Before cleaning the appliance, unplug the appliance

from the power mains (unplug the power cord from the

wall outlet).

If the power cord is damaged, it must be replaced by a

service technician or other adequately trained person.

If the appliance will be out of use for a prolonged

period of time, switch it off using the relevant button,

and unplug the appliance from the power mains. Empty

the appliance, defrost it, clean it, and leave the door

ajar.

If LED lighting does not work, call a service technician.

Do not attempt a repair of the LED lighting yourself, as

there is danger of contact with high voltage!

6

413758

To protect the environment, take the obsolete

appliance to an authorized home appliance collection

center.

Packaging is made of environmentally friendly materials

that can be recycled, disposed of, or destroyed without

any hazard to the environment.

Rating plate can be found in the appliance interior. If

the language on the rating plate is not the language of

your choice or the language of your country, replace it

with the one supplied.

WARNING! Keep ventilation openings, in the

appliance enclosure or in the built-in structure, clear of

obstruction.

WARNING! Do not use mechanical devices or other

means to accelerate the defrosting process, other than

those recommended by the manufacturer.

WARNING! Do not damage the refrigerant circuit.

WARNING! Do not use electrical appliances inside

the food storage compartments of the appliance,

unless they are of the type recommended by the

manufacturer.

7

413758

The symbol on the product or its packaging indicates that the product should not

be treated as normal household waste. The product should be taken to an

authorized collection center for waste electric and electronic equipment

processing. Correct disposal of the product will help prevent any negative effects

on the environment and health of people which could occur in case of incorrect product

removal. For detailed information on removal and processing of the product, please

contact the relevant municipal body in charge of waste management, your waste

disposal service, or the store where you bought the product.

8

ADVICE FOR SAVING POWER

WITH REFRIGERATION

APPLIANCES

413758

• Install the appliance as speciﬁ ed in the instruction manual.

• Do not open the door more often than necessary.

• Occasionally make sure air circulation underneath the appliance is unobstructed.

• Condenser unit on the rear wall should be kept clean (see chapter Cleaning the

appliance).

• If the gasket is damaged or does not provide a perfect seal for other reasons, have it

replaced as soon as possible.

• Store the food in tightly sealed containers or appropriate packaging.

• Before placing the food in the appliance, cool it to room temperature.

• Defrost frozen food in the refrigerator compartment.

• Remove some of the drawers from the freezer compartment as described in the

instruction manual, in order to make use of the entire interior.

• Defrost your conventional freezer when an approximately 3-5 milimeter layer of of frost

or ice has built up on the refrigerated surfaces.

• Make sure the layout of shelves in the compartment is uniform and that the food

is placed so that the air can freely circulate in the appliance interior (observe the

recommended placement of food as described in the instructions).

• In appliances with a fan, do not block the fan slots.

• If you do not need the fan or the ionizer, switch them o to reduce power consumption.

9

APPLIANCE DESCRIPTION

413758

• The drawers are protected against pulling out. To remove a drawer from the appliance,

pull it out as far as it will go, then lift at the front and pull out completely.

• Some models also feature a control unit on the door.

A

B

1

2

3

4

5

6

7

8

A Refrigerator

1 Control unit

2 LED lighting of refrigerator

interior

3 Pull-out glass shelf (height-

adjustable)

4 Crisper (fruit and vegetables

drawer)

5 Height-adjustable door bin

6 Bottle shelf

B Freezer

7 Freezer drawers

8 Glass shelves

10

INSTALLATION AND CONNECTION

413758

SELECTING THE ROOM

• Install the appliance in a dry and well ventilated room. The appliance will operate correctly

if the environment temperature is in the interval speciﬁ ed in the table. The appliance class is

indicated on the rating plate / label with the basic information on the appliance.

Class Temperature

SN (subnormal)

from +10°C to +32°C

N (normal)

from +16°C to +32°C

ST (subtropical)

from +16°C to +38°C

T (tropical)

from +16°C to +43°C

Warning: Make sure the room where the appliance is installed is large enough. There

should be at least 1 m

3

of space per 8 grams of refrigerant. Amount of refrigerant is stated

on the rating plate in the appliance interior.

INSTALLING THE APPLIANCE

Appliance installation should be carried

out by at least two persons to avoid any

physical injury or damage to the appliance.

• The appliance must stand level and stable

on a solid base. At the front, the appliance

is ﬁ tted with two adjustable legs that can

be used to level the appliance. At the rear

side, casters allow for easier installation of

the appliance (only with some models).

• There should be a clearance of at least 5 cm

between the appliance and any cupboard

installed above it, in order to allow adequate

cooling of the condenser unit.

• The appliance is supplied with two

spacers which should be installed on

the lower part of the housing to prevent

from pushing the appliance too close to

the wall. Appliance may also be installed

without the spacers; however, this may

increase power consumption.

11

413758

CONNECTING THE APPLIANCE

• Connect the appliance to the power mains using a connection cable. The wall outlet

should be ﬁ tted with a ground contact (safety socket). Nominal voltage and frequency

are indicated on the rating plate/label with basic information on the appliance.

• The appliance must be connected to the power mains and grounded in compliance

with the e ective standards and regulations. The appliance will withstand short-term

deviations from the nominal voltage, but not more than +/- 6%.

• Do not expose the appliance to direct sunlight and do not place it near any source of

heat. If this cannot be avoided, install an insulation panel.

• The appliance may stand alone or it may be placed ext to a cupboard or a wall. Consider

the clearance required to fully open the door in order to allow pulling out the drawers

and shelves (see installation diagram).

680 mm

632 mm

600 mm

1249 mm

688 mm

640 mm

600 mm

644 mm

max 90°

1

201 mm

1194 mm

1242 mm

max 720 mm

640 mm

max 90°

min 30 mm

ORA IT O

min 42 mm

12

CHANGING THE DIRECTION OF

DOOR OPENING

413758

VERSION I – CONTROLS IN THE APPLIANCE INTERIOR

Tools required: socket wrench No. 8, Phillips screwdriver, torx 25, flat screwdriver

The procedure to change the direction of door opening should be carried out by at least

two persons.

1. Remove the upper hinge cover (A).

2. Unscrew the upper hinge (B) and remove the upper door (C).

3. Then remove the covering plugs (D), unscrew the mid hinge (E) and remove the lower

door (F) from the lower hinge (G).

4. Tilt the appliance backwards (make sure you do not press against the condenser unit

on the rear wall of the appliance as this may damage the cooling system), unscrew the

lower hinge (G) and the foot (H) and move them to the opposite side. Make sure the

washer is installed like it was before disassembly.

5. Move the door hinges (I) to the opposite side.

6. Place the Mid hinge (E) on the lower door (F) and place the lower door on the lower

hinge (G). Fasten the mid hinge (the door should be open while you do this). Do not

forget to place the washers (J) and covering plugs (M) as they were placed before the

disassembly.

7. Place the upper door (C) over the middle hinge (E), remove the covering cap (K) and

fasten the upper hinge (B).

8. Install the upper hinge cover (A) and the covering cap (K).

9. Changing the side of the handle (L): remove the covering plugs/caps, undo the screws

and fasten the handle on the opposite side. Place the covering plugs/caps on the

opposite side.

At ORA-ITO appliances alteration of door opening direction is

not possible.

13

413758

1

2

E

F

3

G

H

4

5

E

F

J

M

6

8

7

9

C

K

B

A

K

B

C

D

I

D

L

14

413758

VERSION II – CONTROLS ON THE DOOR

Tools required: socket wrench No. 8, Phillips screwdriver, torx 25, flat screwdriver

The procedure to change the direction of door opening should be carried out by at least

two persons.

1. Remove the upper hinge cover (A) and the cover from the connector (B1).

2. Unplug the connector (C), unscrew the upper hinge (D) and remove the upper door (E).

3. Remove the side panels (F) and (G), then unscrew and remove the middle panel (H).

4. Move the upper hinge (A) and the connector and cable to the opposite side. Replace

all three panels (F), (G), and (H). Make sure the cable runs through the grooves in the

panels like it did before disassembly.

5. Then remove the covering plugs (I), unscrew the mid hinge (J) and remove the lower

door (K) from the lower hinge (L).

6. Tilt the appliance backwards, undo the lower hinge (L) and the foot (M) and install them

on the opposite side. Make sure the washer is installed like it was before disassembly.

7. Move the door bearings (N) and retainers (S) to the opposite side.

8. Place the Mid hinge (J) on the lower door (K) and place the lower door on the lower

hinge (L). Fasten the mid hinge (the door should be open while you do this). Do not

forget to place the washers (O) and covering plugs (I) as they were placed before the

disassembly.

9. Place the upper door (E) on the middle hinge (J). Remove the covering plugs (P) and

(B2). Reconnect the connector (C) and fasten the upper hinge.

10.Install the over of the upper hinge (A), connector cap (B1), and covering caps (P) and

(B2).

11. Changing the side of the handle (R): remove the plugs/caps, undo the screws and

fasten the handle on the opposite side.

Place the plugs/caps on the opposite side.

15

413758

1

2

3

D

4

J

K

5

L

M

6

7

J

K

O

I

8

I

N

10

9

11

E

C

P

D

B2

B1

A

P

I

R

E

D

C

D

GH

F

N

S

16

OPERATING THE APPLIANCE

WITH MECHANIC CONTROLS

413758

SWITCHING THE APPLIANCE ON/OFF

CONTROL UNIT 1

A B

A Temperature setting and on/o knob

B Lighting on/o key

To switch on: rotate the A dial clockwise.

Switching off: Rotate the A knob back to

the position in which the arrow is aligned

with the symbol (caution: appliance

will remain powered, i.e. there will still be

electric current in the appliance).

17

413758

ADJUSTING THE TEMPERATURE

• To set the desired temperature, rotate the

A dial in clockwise direction, i.e. to the

right.

• A change in the environment temperature

will a ect the temperature in the

appliance. Adjust the setting with the A

dial accordingly. Positions towards the

thicker part of the sign mean a lower

temperature in the appliance (cooler).

Settings towards the thinner part of

the sign mean a higher temperature

(warmer).

• If the temperature of the room where the

appliance is installed is below 16°C, we

recommend setting the A dial

temperature to the thickest part of the

sign.

18

APPLIANCE WITH ELECTRONIC

CONTROL

413758

CONTROL UNIT 2

A Temperature setting and on/o knob

To switch on: rotate the A dial clockwise.

To switch off: rotate the A dial so that the

arrow is aligned with the sign (caution:

appliance will remain powered, i.e. there will

still be electric current in the appliance).

A

SWITCHING THE APPLIANCE ON/OFF

A

19

413758

ADJUSTING THE TEMPERATURE

• To set the desired temperature, rotate the A

dial in clockwise direction, i.e. to the right.

• Recommended setting of the A knob is

on the eco position.

• A change in the environment temperature

will a ect the temperature in the appliance.

Adjust the setting with the A dial

accordingly. Positions towards the thicker

part of the sign mean a lower temperature

in the appliance (cooler). Settings towards

the thinner part of the sign mean a higher

temperature (warmer).

•

If the temperature of the room where the

appliance is installed is below 16°C, we

recommend setting the A dial

temperature to the thickest part of the

sign.

A

FREEZER BOOST (SUPER FREEZE) FUNCTION (ONLY IN

SOME MODELS)

Use this setting after switching on the appliance for the first time, before cleaning, or 24

hours before inserting a large amount of food.

Switching on the freezer boost (super

freeze) function:

Rotate the A dial to position .

After the end of the freezer boost cycle,

rotate the A knob back to the desired

setting.

If the freezer boost is not deactivated

manually, it will be automatically switched

off after approximately 2 days. Then the

temperature of the freezer compartment

returns to the most recently set value

(knob position remains at ).

A

20

413758

MANUALLY ADJUSTABLE FLAP (ONLY WITH SOME

MODELS OF NOFROST APPLIANCES)

The flap is located in the fruit and vegetable

bin. As a factory setting, it is in position 2.

If it is not possible to reach the right

temperature by adjusting the settings with

the knob A, then set the flap as described in

the section »Troubleshooting«.

Page is loading ...

Gorenje NRK6192JBK User manual

Gorenje NRK6192JBK User manual

Related papers

Other documents