Page is loading ...
TCONTROL-CONT-03
COMPACT MICROPROCESSOR CONTROLLER
OPERATING AND INSTALLATION MANUAL
nVent.com | 3
CONTENTS
Section − 1 Introduction ...................................................... 4
1.1 Preface ........................................................................4
1.2 Type designation ........................................................ 5
1.3 Scope of delivery ........................................................ 5
1.4 Accessories ................................................................ 5
1.5 Type-dependent factory settings ...............................6
Section − 2 Installation .......................................................9
2.1 Installation site and ambient conditions ...................9
2.2 Dimensions ..................................................................9
2.3 Installation ................................................................... 9
Section − 3 Electrical connection ......................................10
3.1 Installation notes.......................................................10
3.2 Electrical isolation ..................................................... 11
3.3 Connection diagram ..................................................11
Section − 4 Operation .......................................................12
4.1 Display and operating elements ............................... 12
4.2 Level concept ............................................................12
4.3 Userlevelconguration ............................................13
4.4 Deningvarioususerlevels ...................................... 14
4.5 Entries and operator prompting ...............................14
4.6 Controller ...................................................................15
4.7 Display of the software version ................................ 16
Section − 5 Operator level .................................................17
Section − 6 Parameter level ..............................................17
Section − 7 Conguration level .........................................19
7.1 Analoginput ..............................................................21
7.2 Controller ...................................................................23
7.3 Rampfunction ...........................................................26
7.4 Limit comparators ..................................................... 26
7.5 Timer .......................................................................... 28
7.6 Outputs ......................................................................30
7.7 Binaryfunctions ........................................................32
7.8 Display/Operation/Servicecounter .......................... 34
7.9 Interface .....................................................................38
Section − 8 Supplement ....................................................39
8.1 Technical Data ...........................................................39
8.2 Alarmandfaultmessages .......................................43
8.3 Self-optimization .......................................................44
4 | nVent.com
1. Introduction
1.1 Preface
Pleasereadthismanualbeforecommissioningthedevice.Keep
themanualinaplaceaccessibletoallusersatalltimes.Your
commentsareappreciatedandmayassistusinimprovingthis
manual.
Allnecessarysettingsaredescribedinthisoperatingmanual.
Manipulationsnotdescribedinthemanualorexpresslyforbidden
willjeopardizeyourwarrantyrights.Pleasecontactthenearest
subsidiaryortheheadoffice,shouldyouencounterproblems.
Themanualisvalidfromdevice software version 223.01.04
Chapter 4.7 “Display of the software version”
Warning signs
DANGER!
This symbol indicates that Injury or death caused by electrical
shockcan/mayoccur,iftherespectiveprotectivemeasuresare
notcarriedout.
CAUTION!
This symbol in combination with the signal word indicates
that Damage to assets or data losswilloccur,iftherespective
protectivemeasuresarenotcarriedout.
Note symbols
TIP!
This symbol refers to an Important informationabouttheproduct
oritshandlingoradditionaluse.
REFERENCE!
This symbol refers to Further informationinothersections,
chaptersormanuals.
nVent.com | 5
1.2 Type designation
Type key Type description
702071/9-1131-23-00
(nVent Part No.:
1244-0006829)
TCONTROL-CONT-03
nominaldimension48mmx48mm
• 1analoginput
• 3 relays
702071/9-1134-23-00
(nVent Part No.:
1244-0006830)
TCONTROL-CONT-03/MA
nominaldimension48mmx48mm
• 1analoginput
• 2 relays
• 1analogoutput(usercongurable
0/4…20 mA or 0/2…10 V)
702071/9-1131-23-53
(nVent Part No.:
1244-0006982)
TCONTROL-CONT-03/COM
nominaldimension48mmx48mm
• 1analoginput
• 3 relays
• Interface RS485
702071/9-1134-23-53
(nVent Part No.:
1244-0006981)
TCONTROL-CONT-03/COMA
nominaldimension48mmx48mm
• 1analoginput
• 2 relays
• 1analogoutput|(usercongurable
0/4…20 mA or 0/2…10 V)
• Interface RS485
1.3 Scope of delivery
• Controller(includingsealandfasteningelements)
• OperatingandInstallationmanualINSTALL-148inDINA4format
1.4 Accessories
Computer aided setup and configuration utility
(TCONTROL-CONT-03/CONFIG)
Content:
• MiniCDwithsoftware,license+manuals
• PCinterfacewithUSB/TTLconverter,cableandconnector
Hardware requirements (PC):
• 512 MB RAM
• 250 MB free space on hard disk
• CD ROM drive
• Free USB interface
• Operating system:
Microsoft
1
Windows 2000 / XP / Vista / 7
(32-bit and 64-bit version)
6 | nVent.com
1.5 Type-dependent factory settings
The following tables show the type-dependent factory settings.
The standard factory settings are shown in the respective
sectionsofthismanual.
The settings for type TCONTROL-CONT-03 are also valid for type
TCONTROL-CONT-03/COM.
The settings for type TCONTROL-CONT-03/MA are also valid for
type TCONTROL-CONT-03/COMA.
Set points (available within User level - USEr)
Parameter Factory setting for type
TCONTROL- CONT-03 TCONTROL- CONT-03/MA
Set point 1 (SP1) 5.0 5.0
Set point 2 (SP2) 0.0 0.0
Parameter level (PArA)
Parameter Factory setting for type
TCONTROL- CONT-03 TCONTROL- CONT-03/MA
Proportional
band(Pb1)
0.0 10.0
Derivativetime(dt) 0 s 80 s
Reset time (rt) 0 s 350 s
Configuration level (ConF)
Parameter Factory setting for type
TCONTROL- CONT-03 TCONTROL- CONT-03/MA
Analog input (InP):
Scale low level (SCL) -50 -50
Scale high level
(SCH)
250 250
Controller (Cntr):
Controller type
(CtYP)
1 (= 2-state ON/OFF) 4(=continuous
4…20 mA)
Outputvalueat
OutofRange
100 100
Manualmode inhibited inhibited
Self-optimization inhibited inhibited
1
Microsoft and Windows are registered trademarks of Microsoft Corporation.
nVent.com | 7
Conguration level (ConF) cont...
Parameter Factory setting for type
TCONTROL- CONT-03 TCONTROL- CONT-03/MA
Limit comparator 1 (LC1):
Function(FnCt) lk8 lk8
Alarmvalue(AL) 2.0 2.0
ResponsebyOutof
Range (ACrA)
1 (= ON) 1 (= ON)
Limit comparator 2 (LC2):
Function(FnCt) lk7 lk7
Alarmvalue(AL) 120.0 120.0
ResponsebyOutof
Range (ACrA)
1 (= ON) 1 (= ON)
Binary outputs (OutL):
Binaryoutput1
(Out1)
1(=Controlleroutput1) 5 (= Limit comparator 1)
Binaryoutput2
(Out2)
5 (= Limit comparator 1) 6 (= Limit comparator 2)
Binaryoutput3
(Out3)
0(=nofunction) 0(=nofunction)
Binaryoutput4
(Out4)
6 (= Limit comparator 2)
Analog output (OutA):
Type of signal
(SiGn)
3 (= 4…20 mA)
Display/Operation/Service counter (diSP):
Decimal place
(dECP)
1 (= one digit after
decimal point)
1 (= one digit after
decimal point)
Service interval
(oCAL)
30000 0 (= switched off)
Level inhibit Parameter and
Congurationlevel
Parameter and
Congurationlevel
8 | nVent.com
User level (USEr) configuration
Factory setting for type
TCONTROL-CONT-03 TCONTROL-CONT-03/MA
# Parameter Name Parameter Name
1 Set point 1 SP1 Set point 1 SP1
2 Limit comparator 1:
Limitvalue
(Alarmvalue)
AL1 Limit comparator 1: Limit
value
(Alarmvalue)
AL1
3 Limit comparator 2:
Limitvalue
(Alarmvalue)
AL2 Limit comparator 2: Limit
value
(Alarmvalue)
AL2
4 Mains ON delay
(Power ON delay)
Strt Mains ON delay
(Power ON delay)
Strt
5 Analoginput:
Probe type
(Sensor type)
InP Analoginput:Probetype
(Sensor type)
InP
6 Display:
Decimal point
dEC Display: Decimal point dEC
7 Parameter set 1:
Proportional band 1
Pb1 Parameter set 1:
Proportional band 1
Pb1
8 Parameter set 1:
Cycle time 1
CY1 (Switched off)
Undocumented parameters
Parameter Factory setting for type
TCONTROL- CONT-03 TCONTROL- CONT-03/MA
Bit parameter:
Parameter 11
(enablestouse
for parameter
“Cy”values
from 1 to 9999)
ON ON
TCRUC-BE.БЛ08.B.01634
nVent.com | 9
2. Installation
2.1 Installation site and ambient conditions
Theambientconditionsattheinstallationsitemustmeetthe
requirementsspecifiedinthetechnicaldata.
Chapter8.1“TechnicalData”Thedeviceisnotsuitableforuse
inareaswithanexplosionhazard(Exareas).
Cleaning the device front
Thedevicefrontcanbecleanedusingwarmorhotwater
(possiblyaddingslightlyacidic,neutralorslightlyalkaline
cleaning agent). It has a limited resistance to organic solvents
(e.g.methylatedspirits,whitespirit,etc.).Donotuseabrasive
orhigh-pressurecleaningequipment.
2.2 Dimensions
Close mounting
Minimum spacing of panelcut-outs horizontal vertical
withoutsetupplug > 8 mm > 8 mm
withsetupplug > 8 mm > 65 mm
45
+0.6
45
+0.6
48
48
44.5
50
90.5
5
44.5
48
(2
)
(1
)
(1) ConnectionforPCinterfaceadapter(setupplug)
(2) Panelcut-out
2.3 Installation
1. Insertthedevicefromthefrontintothepanelcut-out.
2. Pushthefasteningframefromthepanelrearontothedevicebodyand
pressthespringsagainstthepanelrearuntilthelugsengageintheirslots
anditissucientlyfastened.
10 | nVent.com
3. Electrical connection
3.1 Installation notes
• Thechoiceofcable,theinstallationandtheelectrical
connectionofthedevicemustconformtotherequirements
ofVDE0100“RegulationsontheInstallationofPowerCircuits
with Nominal Voltages below 1000 V” or the appropriate local
regulations.
• Theelectricalconnectionmustonlybecarriedoutbyqualified
personnel.
• Theinstrumentshallbeoperatedbymainsprotectedwitha
branchcircuitryovercurrentprotectiondevicenotmorethan
20Amps.Forservicing/repairingaDisconnectingDeviceshall
beprovidedtodisconnectallconductors.
• Theloadcircuitmustbefusedforthemaximumrelaycurrent,
inordertopreventtheoutputrelaycontactsbecomingwelded
intheeventofashortcircuitoccurringatthatpoint.
• The electromagnetic compatibility conforms to the standards
andregulationscitedinthetechnicaldata.
• Runinput,outputandsupplycablesseparatelyandnotin
parallel with one another.
• Sensorandinterfacecablesshouldbeshieldedcableswith
twistedconductors.Donotruncablesclosetocurrent-carrying
componentsorcables.Groundtheshieldingononeside.
• Donotconnectanyadditionalloadstothesupplyterminalsof
the device.
DANGER!
Hazardouselectricalvoltage.
Injuryordeathcausedbyelectricshock.Theelectricalconnection
mustonlybecarriedoutbyqualifiedpersonnel.
TIP!
Identify the device version by way of the type key.
Installation information on conductor cross sections
Cable size Cross section
Solid core ≤1.3mm
2
Strandedwire,withcore-end
ferrule
≤1.0mm
2
Plug-interminalstrips(screwterminals).
nVent.com | 11
3.2 Electrical isolation
2300 V AC
30 V AC
50 V DC
2300 V AC
30 V AC
50 V DC
(1)
(2)
(3)
(7)
(6)
(5)
(4)
(1)Analoginput
(2)Binaryinputs/OutputK3(Logics)
(3)Setupinterface
(4)Voltagesupply
(5) RS485 interface
(6)Analogoutput
(7)OutputsK1,K2andK4(relay)
3.3 Connection diagram
1
2
5
6
N(L-)
L1(L+)
14
13
17
20
21
22
23
RxD/TxD
0/4—20mA
-
+
0/2—10V
+
AC/
DC
19
18
0/4—20mA
0/2—10V
+
-
+
-
24
(1)
(2)
(5.1)
(4)
(8
)
(7)
(6
)
-
+
(6.1)
(6.2)(6.3) (6.4)
(3)
0/14V
+
-
(5.2)
(1) Output1(K1):Relay230
V AC/3 A
(2) Output2(K2):Relay230V
AC/3 A
(3) Output3(K3):Logic0/14
V (alternative to binary
input1,congurable)
(4) Output4(K4)(option):Analog
outputorRelay230VAC/3A
(5.1) Binaryinput1
(for potential-free contact);
(alternativetooutput3,
congurable)
(5.2) (5.2)Binaryinput2
(for potential-free contact);
(alternativetoinput
0/2—10V,congurablewith
setupprogram)
(6) Analoginput
(6.1) Standardsignals(input
0/2—10V alternative to
binaryinput2)
(6.2) Thermocouple
(6.3) RTDtemperatureprobe
(3 wire)
(6.4) RTDtemperatureprobe
(2 wire)
(7) RS485 interface (Option) (8) Voltagesupply110—240VAC
(Option: 20—30 V AC/DC)
12 | nVent.com
4. Operation
4.1 Display and operating elements
(1) Red 7-segment display(factory-setting:Processvalue);
4-digit,configurabledecimalplace(automaticadjustmenton
display overflow)
(2) Green 7-segment display(factory-setting:Setpointvalue);
4-digit,configurabledecimalplace,servesalsoforoperator
guide(displayofparameterandlevelsymbols)
(3) Signals, yellow LED
Switchingstatesofthebinaryoutputs1...4(displaylit=ON)
(4) Keys
Programming key
leavelevel/functionkey
Chapter7.8“Display/Operation/Servicecounter”
Valuereduction/previousparameter
Valueincrease/nextparameter
(5) Signals, green LED
• Manualmodeactive
• Rampfunctionactive
• Timer active
4.2 Level concept
Theparametersforthedevicesettingarestructuredindifferent
levels.
Normal display
>2s
or timeout
Navigation principle
one level
backward
one level
forward
next/previous
parameter
F
EXIT
F
EXIT
PArA
ConF
OPr/USEr
1
1. Either the Operator (OPr) or
the User level (USEr) exists
Conguration level ConF
- Analog input in P
- Controller Cntr
- Ramp function rAFC
- Limit comparators LC
- Timer tFCt
- Outputs OutP
- Binary functions b
,
nF
- Display d
,
SP
- Interface intF
Operator level OPr
Set points, process data, ...
User level USEr
Up to any eigth parameters
(ex-factory: preassigned)
Parameter level PAr A
-Pb1,dt,rt...
nVent.com | 13
Chapter 5 “Operator level”
Chapter 6 “Parameter level”
Chapter7“Configurationlevel”
TIP!
If no key is pressed for 180 s the device changes back to normal
display(factory-setting).ThesettingcanbechangedintheSetup
program(Display/Operation/Servicecounter->Operation->
Time-out).
4.3 User level configuration
Amaximumofeightfrequentlyusedparameterscanbemade
availableintheUserlevel.UsetheSetupprogramtoconfigure
these parameters.
Oncetheseparametersareselectedacustomerfriendlyname
canbeassigned.Namescanconsistoutofmaximumfour
characters (represented on 7-segment display). If no name is
assignedthefactorydefaultswillbeused.
Figure shows the menu of the Setup program
(in case of TCONTROL-CONT-03/MA and .../COMA parameter 8 is
switched off)
14 | nVent.com
4.4 Defining various user levels
Accesstotheindividuallevelscanbeinhibited.
Code
Operator, User
level
Parameter
level
Configuration
level
0 free free free
1 free free inhibited
2 free inhibited inhibited
3 inhibited inhibited inhibited
1. Forcodeentryuse
and (simultaneouslyfor>5s)
2. Change code by pressing
(display blinks!)
3. Entercodeusing
and (Ex-factory:alllevelsenabled)
4. Returntothenormaldisplayusing
orautomaticreturnafter
180 s
Theparameterandconfigurationlevelcanalsobeinhibitedvia
thebinaryfunction.
Chapter7.7“Binaryfunctions”
4.5 Entries and operator prompting
Entering values
Whenentriesaremadewithinthelevels,theparametersymbol
appears in the lower display.
Change value
(top - red)
Parameter flashes
Select parameter
(bottom - green)
P
1. Select parameter by pressing or
2. Changetotheentrymodeusing
(lower display blinks)
3. Changeavalueusing
and
Thevaluealtersdynamicallyforaslongasthekeyiskept
pressed.
4. Take over the entry with
orautomaticreturnafter2sor
cancel the entry with
thevaluewillnotbeapplied.
TIP!
Ifthefunctionkey
ispressedfor>2s,thedevicechanges
back to normal display.
nVent.com | 15
Time entry
A decimal place is mapped in the centre and on the right to
displaytimes.Thetimeunitcanbeconfigured.
Chapter 7.5 “Timer”
Change value
(top - red)
Parameter flashes
Select Parameter
(bottom - green)
P
1. Select parameter by pressing or
2. Changetotheentrymodeusing
(lower display blinks)
3. Changeavalueusing
and
Thevaluealtersdynamicallyforaslongasthekeyiskeptpressed.
4. Take over the entry with
orautomaticreturnafter2sor
cancel the entry with
thevaluewillnotbeapplied.
4.6 Controller
Increase set point value
Reduce set point value
Normal display:
Regulation to set
point value 21,0
>2s
Manual mode:
Output value 30%
Further levels:
P
alternatively
1
P
F
EXIT
F
EXIT
Normal display
Innormaldisplay,thecontrollerregulatestotheenteredsetpoint
value.
Changing the set point value
From the normal display:
1. Changethesetpointvalueusing
and (thevaluewillbe
automaticallyapplied)
Thelongerthekeyiskeptpressed,thefasterthesetpoint
valuechanges.
USEr
1
OPr
1
PArA
ConF
16 | nVent.com
Changing to the manual mode
Inthemanualmode,thecontrolleroutputvaluecanbechanged
manually.
1. Changetothemanualmodeusingfunctionkey
(> 2 s)
(ex-factorysetting)
Theoutputvalueisdisplayedinpercentinthelowerdisplay.
The"Manualmodeactive"LEDisalsolit.
2. Changetheoutputvalueusing
and
Withamodulatingcontroller,theactuatorisopenedorclosed
usingthekeys.
Thevariouslevelscanbeaccessedinthemanualmode.
TheSetupprogramcanbeusedtoconfigurethedefaultoutput
valueonachangeover.Themanualmodecanalsobeinhibited.
Chapter 7.2 “Controller”
Thecontrollerautomaticallychangestomanualmodeinthe
eventofoverrange/underrangeandprobebreak.
Manual mode exit
1. Exitthemanualmodeusingfunctionkey
(> 2 s)
Operation via binary functions
Furtheroperatingpossibilitiesforthefixedvaluecontrollercanbe
realisedviabinaryfunctions.
Chapter7.7“Binaryfunctions”
4.7 Display of the software version
Simultaneouslypressthe and keys to display the software
version.
Four-digitdisplay;example:“01.01”incaseofsoftwareversion
xxx.01.01
Levels can be inhibited.
Chapter 4.4 „Defining various user levels“
Normal display
>2s
or timeout
Navigation principle
one level
backward
one level
forward
next/previous
parameter
F
EXIT
F
EXIT
Levels can be inhibited.
Chapter4.4“Definingvarioususerlevels”
Operator level OPr
Setpointvalues,
processdata,...
1. Operator level (OPr) only visible
if no User level (USEr) exists
OPr
1
nVent.com | 17
5. Operator level
Parameters
Dependingontheconfiguration,thefollowingvaluesaredisplayed:
Symbol Meaning
SP 1
Setpointvalue1(canbeedited)
SP 2
Setpointvalue2(canbeedited),onlywhenswitching
overtosetpointvalue2v
Chapter7.7“Binaryfunctions”
SPr
Rampsetpointvalue(onlyifcongured)
Chapter7.3“Rampfunction”
inP 1
Measuredvalueofanaloginput1
y
Outputvalue
t1
Timertime(onlyifconguredandtimerisnotrunning)
Chapter 7.5 “Timer”
tL
Timerrunningtime(onlyiftimerruns)
Chapter 7.5 “Timer”
tr
Residualtimerrunningtime(onlyiftimerruns)
Chapter 7.5 “Timer”
OC
Servicecounterdisplay(onlyifservicecounterrunsor
aslongasareachedlimitvaluewasnotreset)
Chapter7.8“Display/Operation/Servicecounter”
6. Parameter level
Normal display
>2s
or timeout
Navigation principle
one level
backward
one level
forward
next/previous
parameter
F
EXIT
F
EXIT
Levels can be inhibited.
Chapter4.4“Definingvarioususerlevels”
Parameter level PArA
Pb1
.
.
.
y2
PArA
OPr/USEr
1
1. Either the Operator (OPr) or
the User level (USEr) exists
18 | nVent.com
Parameters Symbol
Value
range Description
Proportional
band
Pb1
0…9999 Proportional band
AtPb1,2=0,thecontrollerstructure
isineffective.Forthecontinuous
controllerPb1,2mustbe>0.
Pb2
1)
0…9999
Derivative
time
dt
0…
9999s
Inuencesthedifferentialcomponent
ofthecontrolleroutputsignal
The larger the derivative time
the higher the effectiveness of
the D component.
Reset time
rt
0…
9999s
Inuencestheintegralcomponentof
thecontrolleroutputsignal
The larger the reset time the lower the
effectiveness of the I component.
1)For3-statecontrollersonly(controlleroutput2)
Cycle time
ofoutput
Cy1
0…
20…
9999s
Foraswitchingoutput,thecycletime
shouldbeselectedsuchthatonone
handnoinadmissibleprocessvalues
uctuationsaregeneratedandon
the other hand no overload of the
actuatorsoccursbythecyclicsupply
of energy.
Cy2
1)
0…
20…
9999s
Dead band
db
0.0…
999.9
Spacing between the two control
contacts of the 3-state controller and
themodulatingcontroller
Hysteresis
HyS1
0.0…
1.0…
999.9
Hysteresis for switching controller
withPb1,2=0.
100%
y
x
w
HyS1,2
0%
HyS2
1)
0.0…
1.0…
999.9
Valve
runtime
tt
5…60…
3000s
Usedruntimerangeofthecontrol
valve(actuator)ofthemodulating
controller
Operating
value
y0
-100…
0…
+100%
OutputvalueforPandPDcontrollers
(forx=wisy=Y0)
Output
valuelimits
y1
0…100% Maximumoutputvaluelimit
Minimumoutputvaluelimit
(Only effective when Pb>0!)
y2
-100…
+100%
1)For3-statecontrollersonly(controlleroutput2)
nVent.com | 19
Standard factory settings are shown bold.
Non-standard factory settings:
Chapter 1.5 “Type-dependent factory settings”
Parameter display independent of the controller type:
Chapter 7.2 “Controller”
Decimal places for some parameters depend on the device
setting:
Chapter7.8“Display/Operation/Servicecounter”
7. Configuration level
Normal display
>2s
or timeout
Navigation principle
one level
backward
one level
forward
next/previous
parameter
F
EXIT
F
EXIT
Levels can be inhibited.
Chapter4.4“Definingvarioususerlevels”
TIP!
Parametersarenotdisplayedunlesstheequipmentlevelpermits
thefunctionassignedtotheparameter.Thismeans,forexample,
thatinterfaceparameterscanonlybeconfigured,ifthedeviceis
equippedwithaninterface.
TIP!
SomeparameterscanonlybeprogrammedthroughtheSetup
program.Inthefollowingtables,thesearemarkedinthe
“Parameters”columnwith“(Setup)”.
TIP!
Standard factory settings are displayed bold in the following
tablesinthe“Value/Selection”and“Description”columns.
Non-standard factory settings are shown in Chapter 1.5
“Type-dependent factory settings”.
TIP!
Foractivationofbinaryinput2thesetupprogramisrequired
(Hardware assistant).
Conguration level ConF
- Analog input in P
- Controller Cntr
- Ramp function rAFC
- Limit comparators LC
- Timer tFCt
- Outputs OutP
- Binary functions b
,
nF
- Display d
,
SP
- Interface intF
PArA
ConF
OPr/USEr
1
1. Either the Operator (OPr) or
the User level (USEr) exists
20 | nVent.com
Analog selector
SomeparametersintheConfigurationlevelallowuserstoselectfroma
seriesofanalogvalues.Thelistbelowshowsallavailableoptions.
Value Description
0 Deactivated
1 Analoginput
2 Processvalue
3 Currentsetpointvalue
4 Ramplimitvalue
5 Rampsetpointvalue
6 (Reserved)
7 (Reserved)
8 Setpointvalue1
9 Setpointvalue2
10 Controlleroutputvalue(-100%…+100%)
11 Controlleroutput1(0…+100%;e.g.“Heating”)
12 Controlleroutput2(0…-100%;e.g.“Cooling”)
13 Timerruntime(timeunitofthetimer)
14 Residualtimerruntime(timeunitofthetimer)
15 (Reserved)
16 (Reserved)
17 (Reserved)
/
