Christie CP2315-RGB User manual

User Guide

020-102768-03

CP2315-RGB

NOTICES

COPYRIGHT AND TRADEMARKS

Cop

yright

©

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this

document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary

depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on

information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied

warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection

with the performance or use of this material. Manufacturing facilities in Canada and China are ISO 9001 certified. Manufacturing facilities in Canada are also

ISO 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. In

addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the

warranty does not cover:

a.

Problems or damage occurring during shipment, in either direction.

b.

Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or use

of a product with any non-Christie interface device.

c.

Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake, or other natural disaster.

d.

Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christie

authorized repair service provider.

e.

Use of third party product enclosures for environmental protection during outside use must be approved by Christie.

f.

Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified or

approved by Christie for such use.

g.

Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected from

precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature set

forth in the specifications for such product.

h.

Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold

by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or

(ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in

accordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol

means that electrical

and electronic equipment, at their end-of

-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according

to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the

environment we live in!

Content

Safety precautions................................................ 10

Gener

al safety precautions.............................................10

Laser safety precautions..............................................11

AC/power precautions................................................11

Light intensity hazard distance..........................................12

Product labels.....................................................14

General hazards................................................. 14

Mandatory action.................................................15

Electrical labels..................................................15

Additional hazard labels............................................ 15

Introduction..................................................... 17

Product documentation...............................................17

Related documentation.............................................17

Projector overview..................................................17

Contact your dealer.................................................18

Key features......................................................18

Understanding the Christie touch panel interface...............................19

Operating the projector.............................................20

Projector power modes...............................................20

Turning the projector on or off.......................................... 20

Logging on to the projector............................................ 20

Logging out of the projector............................................21

Turning the touch panel on or off.........................................21

Calibrating the touch panel display........................................21

Turning the light source on or off.........................................21

Opening or closing the shutter.......................................... 22

Selecting a channel................................................. 22

Adding a network time protocol server..................................... 22

Deleting a network time protocol server.................................... 22

Changing the time zone.............................................. 23

Changing the time format............................................. 23

Automatically adjusting the time for Daylight Saving Time.........................23

CP2315-RGB User Guide 3

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Manually adjusting the time offset........................................24

Changing the orientation of the projected image...............................24

Changing the projector host name........................................25

Changing the temper

ature display........................................25

Managing the light source...........................................26

Creating a new laser file..............................................26

Modifying an existing laser file.......................................... 27

Copying existing laser settings to a new file..................................28

Deleting a laser file................................................. 28

Managing user accounts............................................29

Default user access permissions......................................... 29

Adding a user account............................................... 29

Changing user account permissions.......................................29

Changing a user account password........................................30

Deleting a user account...............................................30

Network settings..................................................31

Connecting the projector to the theater network...............................31

Connecting the projector to network attached storage............................31

Connecting the projector to a media or content network.......................... 32

Activating SNMP...................................................32

Downloading MIB information...........................................32

Setting up an integrated media block..................................34

Selecting IMB preferences.............................................34

Activating IMB marriage.............................................. 34

Managing content.................................................35

Content manager icons...............................................35

Ingesting content and keys............................................ 35

Canceling an ingest.................................................36

Viewing remaining NAS storage capacity....................................36

Filtering content by type..............................................36

Viewing available keys............................................... 36

Filtering the key list.................................................36

Deleting local content................................................37

Deleting keys.....................................................37

Collapsing or expanding columns.........................................37

Content

CP2315-RGB User Guide 4

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Viewing content details...............................................37

Pla

yback controls...................................................38

Loading and playing content............................................38

Viewing an active content item..........................................39

Looping content................................................... 39

Unloading content..................................................39

Managing playlists................................................ 40

Creating a new playlist...............................................40

Reordering playlist content.............................................40

Adding a time offset to a macro..........................................40

Replacing playlist content............................................. 41

Removing playlist content............................................. 41

Copying a playlist.................................................. 42

Opening an intermission playlist......................................... 42

Viewing an active playlist..............................................42

Viewing details about playlist content......................................42

Importing a playlist.................................................42

Exporting a playlist................................................. 43

Deleting a playlist..................................................43

Working with channels.............................................44

Adding a channel for HDMI input.........................................44

Adding a channel for IMB input..........................................45

Editing an existing channel.............................................46

Copying existing channel settings to a new channel.............................46

Viewing the channel list...............................................47

Moving a channel up or down the channel list.................................47

Deleting a channel..................................................47

Managing color setting files.........................................48

Creating a MCGD file................................................ 48

Editing an existing MCGD file........................................... 48

Copying existing MCGD file settings to a new file...............................49

Deleting a MCGD file................................................ 49

Creating a TCGD file.................................................49

Editing an existing TCGD file............................................50

Copying existing TCGD file settings to a new file...............................50

Deleting a TCGD file.................................................50

Content

CP2315-RGB User Guide 5

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Adjusting the image size and position................................. 51

Activating the Intelligent Lens System......................................51

Creating a new ILS file...............................................51

Automatically calibrating the ILS.........................................51

Editing ILS file settings...............................................52

Copying existing ILS file settings.........................................52

Deleting an ILS file................................................. 52

Resetting the lens..................................................52

Creating a source file................................................53

Editing source file settings.............................................53

Copying existing source file settings to a new source file..........................53

Deleting a source file................................................53

Creating a screen file................................................54

Editing screen file settings.............................................54

Copying existing screen file settings to a new screen............................ 54

Deleting a screen file................................................54

Performing digital convergence..........................................55

Resetting digital convergence to the default settings.............................55

Adjusting the image............................................... 56

Correcting vignetting................................................ 56

Correcting keystone effect.............................................56

Masking the screen edges.............................................57

Test patterns.....................................................59

Displaying a test pattern..............................................59

Turning off a test pattern..............................................59

Importing a test pattern..............................................60

Deleting a test pattern............................................... 60

Working with the scheduler......................................... 61

Scheduling a playlist, content, or automation.................................61

Editing a scheduled event............................................. 62

Copying and pasting an existing scheduled event...............................62

Copying and pasting scheduled events for an entire day.......................... 62

Cutting and pasting a scheduled event..................................... 62

Deleting a scheduled event............................................ 63

Deleting scheduled events for an entire day..................................63

Changing the day of the week the scheduler starts..............................63

Content

CP2315-RGB User Guide 6

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Turning the scheduler off..............................................63

Managing storage devices.......................................... 64

Adding a new stor

age device........................................... 64

Editing storage device settings..........................................64

Setting a storage device as a primary drive.................................. 64

Deleting a storage device............................................. 65

Adding a remote ingest source..........................................65

Editing remote ingest source settings......................................65

Deleting a remote ingest source......................................... 66

Managing projector setting files......................................67

Creating a 3D file.................................................. 67

Editing an existing 3D file............................................. 67

Copying a 3D file...................................................68

Deleting a 3D file...................................................68

Managing audio settings............................................69

Setting the global audio delay...........................................69

Setting the audio output rate...........................................69

Mapping channels.................................................. 69

Enabling Dolby Atmos................................................70

Editing Dolby Atmos settings........................................... 70

Disabling Dolby Atmos............................................... 70

Setting up multiple projectors........................................71

Enabling multiple projectors............................................71

Adding a slave projector..............................................71

Disabling multiple projectors........................................... 72

Disabling a slave projector.............................................72

Deleting a slave projector............................................. 72

Automation......................................................73

Available macro actions...............................................73

Fire alarm macro...................................................74

Christie ACT actions.................................................74

JNIOR actions.....................................................75

Dolby Cinema processor actions......................................... 75

SKA-3D actions....................................................76

Creating a macro...................................................76

Content

CP2315-RGB User Guide 7

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Running a macro...................................................76

Adding an action item to an existing macro.................................. 77

Adding a macro to an existing macro...................................... 77

Deleting a macro...................................................77

Adding an automation device to y

our auditorium...............................77

Modifying automation device settings......................................78

Removing an automation device from your auditorium........................... 78

Creating a new playlist trigger.......................................... 79

Editing existing playlist trigger settings.....................................79

Deleting a playlist trigger..............................................79

Creating a new global trigger...........................................79

Editing existing global trigger settings......................................80

Deleting a global trigger.............................................. 80

Importing a device library.............................................80

Viewing a device library...............................................80

Deleting a device library..............................................80

Enhancements and licensing........................................82

Enabling an enhancement.............................................82

Enabling RealD 3D EQ................................................82

Importing a rental license file...........................................82

Backing up, restoring, and upgrading files..............................84

Creating a new backup file.............................................84

Exporting a backup file...............................................84

Importing a backup file...............................................84

Sorting backup files by name and date created................................85

Deleting a backup file................................................85

Adding an upgrade package............................................85

Installing an upgrade package.......................................... 85

Comparing upgrade packages...........................................86

Deleting an upgrade package...........................................86

Restoring settings from a backup file...................................... 86

Restoring factory default settings.........................................86

Accessing projector diagnostics..................................... 87

Retrieving and downloading system logs....................................87

Running the projector interrogator........................................87

Viewing laser diagnostic information.......................................88

Content

CP2315-RGB User Guide 8

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Downloading a certificate..............................................88

Regulatory...................................................... 89

Safet

y......................................................... 89

Electro-magnetic compatibility.......................................... 89

Emissions..................................................... 89

Immunity..................................................... 89

Environmental.................................................... 90

Content

CP2315-RGB User Guide 9

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Safety precautions

Learn about the safet

y precautions related to the Christie CP2315-RGB projector. This projector is

intended for use in a cinema environment.

General safety precautions

Read all safety and warning guidelines before installing or operating the projector.

Warning! If not a

voided, the following could result in death or serious injury.

• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be

tripped over, or damaged by persons walking on or objects rolling over the cables.

• This product must be installed within a restricted access location not accessible by the general

public.

• Only personnel who are trained on the precautions for the restricted access location can be

granted entry to the area.

• Install the product so users and the audience cannot enter the restricted area at eye level.

• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.

• High leakage current present when connected to IT power systems.

• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts

specified by Christie.

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• HAZARDOUS SUBSTANCE! Use caution when handling the product as it contains ethylene glycol.

Do not ingest coolant. For information on safe handling, refer to the Safety Data Sheet (SDS) for

the coolant.

• A minimum of four people or appropriately rated lift equipment is required to safely lift, install,

or move the product.

• Do not install or operate the projector in any position that does not meet the stated product

specifications for alignment and orientation.

Caution! If not a

voided, the following could result in minor or moderate injury.

• Only Christie qualified technicians are permitted to open product enclosures.

CP2315-RGB User Guide 10

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Laser safety precautions

R

ead all safety and warning guidelines before operating the projector laser.

Warning! If not a

voided, the following could result in death or serious injury.

• Do not operate the cinema projector without all of its covers in place.

• LASER RADIATION HAZARD! This projector has a built-in Class 4 laser module. Never attempt to

disassemble or modify the laser module.

• Do not look directly into the lens when the light source is on. The extremely high brightness can

cause permanent eye damage.

• Possible hazardous optical radiation emitted from this product. (Risk group 3)

AC/power precautions

R

ead all safety and warning guidelines before connecting to AC power.

Warning! If not a

voided, the following could result in death or serious injury.

• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by

Christie.

• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and

power plug meet the appropriate local rating standards.

• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage

and current, as specified on the license label.

• SHOCK HAZARD! The AC power cord must be inserted into an outlet with grounding.

• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product

by Christie qualified technicians or electricians before it can be connected to power.

• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,

removing components, or opening any enclosure.

• Install the product near an easily accessible AC receptacle.

• Always connect the ground or earth first to reduce shock hazard.

• A certified electrician must be present during installation to ensure the installation meets the

local electrical code.

Caution! If not a

voided, the following could result in minor or moderate injury.

• Use an appropriately sized strain relief connector with the knockout plate provided, to ensure

adequate environmental sealing and to prevent the AC supply cable from accidentally being torn

out or rubbing against the knockout plate.

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

• SHOCK HAZARD! Power supply uses double pole/neutral fusing.

Safety precautions

CP2315-RGB User Guide 11

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Light intensity hazard distance

This projector has been classified as Risk Group 3 as per the IEC 62471:2006 standard due to possible

hazardous optical and thermal r

adiation being emitted.

Warning! If not a

voided, the following could result in serious injury.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be

permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC

62471:2006.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam

within the hazard distance or install the product at the height that prevents exposure of

spectators' eyes within the hazard distance. The hazard zone must be no lower than 2.5 meters

(US installations) or 2.0 meters (global installations) above any surface upon which any persons

are permitted to stand and the horizontal clearance to the hazard zone must be a minimum 1.0

meters.

• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

The following diagram and table show the zones for ocular and skin hazard distances:

• A—Hazard zone. The region of space where the projection light from the laser-illuminated

projector is abo

ve emission limits for Risk Group 2. The light intensity may cause eye damage

after a momentary or brief exposure (before a person can avert his or her eyes away from the

light source). The light may cause skin burns to occur.

• B—Hazard distance. Operators must control access to the beam within the hazard distance or

install the product preventing potential exposure of the spectators' eyes from being in the

hazard distance.

• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 1.0

meters.

• D—Vertical distance to hazard zone. The hazard zone must be no lower than 2.5 meters (US

installations) or 2.0 meters (global installations) above any surface upon which any persons

are permitted to stand.

• E—Represents the top view of the projector.

Safety precautions

CP2315-RGB User Guide 12

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

• F—Represents the side view of the projector.

F

or US market only, hazard distances based upon FDA guidance document 1400056, Classification and

Requirements for Laser Illuminated Projectors (LIPs), dated February 18, 2015.

Projection Lens Part Number Hazard Distance

(m)

1.05:1 DLPCine HB zoom lens 108-319104-XX 1.2

1.2-1.75:1 DLPCine HB zoom lens 108-350109-XX 1.8

1.39-1.9:1 DLPCine HB zoom lens 108-327103-XX 2.1

1.5-2.2:1 DLPCine HB zoom lens 108-329105-XX 2.3

1.75-2.4:1 DLPCine HB zoom lens 108-321107-XX 2.6

1.9-3.0:1 DLPCine HB zoom lens 108-328104-XX 3.2

2.4-3.9:1 DLPCine HB zoom lens 108-322108-XX 4.1

For all other markets, hazard distances based upon IEC 62471-5:2015, Photobiological Safety of

Lamps and Lamp Systems – Part 5: Image Projectors.

Projection Lens Part Number Hazard Distance

(m)

1.05:1 DLPCine HB zoom lens 108-319104-XX 1.2

1.2-1.75:1 DLPCine HB zoom lens 108-350109-XX 1.8

1.39-1.9:1 DLPCine HB zoom lens 108-327103-XX 2.1

1.5-2.2:1 DLPCine HB zoom lens 108-329105-XX 2.3

1.75-2.4:1 DLPCine HB zoom lens 108-321107-XX 2.6

1.9-3.0:1 DLPCine HB zoom lens 108-328104-XX 3.2

2.4-3.9 DLPCine HB zoom lens 108-322108-XX 4.1

For Installations in the United States

The following must be in place for laser-illuminated projector installations in the United States:

• The projection room shall be clearly identified by the posting of laser warning and restricted

access signs, and by restricting entry through physical means. The projection room sign must

display the warning "No direct exposure to beam shall be permitted".

• The Christie Laser Projection System Installation Checklist must be fully completed after the

installation and sent to [email protected]. A copy can remain on-site. This

checklist can be found as a separate document in the accessory box with the manual.

• Certain US states have additional laser regulatory requirements. Go to www.christiedigital.com

for additional regulatory requirements.

Safety precautions

CP2315-RGB User Guide 13

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Product labels

Learn about the labels that ma

y be used on the product. Labels on your product may be yellow or

black and white.

General hazards

Hazard warnings also apply to accessories once they are installed in a Christie product that is

connected to power.

Fire and Shock Hazard

To prevent fire or shock hazards, do not expose this product to rain or moisture.

Do not alter the power plug, o

verload the power outlet, or use it with extension cords.

Do not remove the product enclosure.

Only Christie qualified technicians are authorized to service the product.

Electrical Hazard

Risk of electric shock.

Do not remo

ve the product enclosure.

Only Christie qualified technicians are authorized to service the product.

General hazard.

Electrocution hazard. To avoid personal injury, always disconnect all power sources before

performing maintenance or service procedures.

Hot surface hazard. To avoid personal injury, allow the product to cool for the recommended

cool down time before performing maintenance or service.

Burn hazard. To avoid personal injury, allow the product to cool for the recommended cool

down time before performing maintenance or service.

Optical radiation hazard. To avoid personal injury, never look directly at the light source.

Moving parts hazard. To avoid personal injury, keep hands clear and loose clothing tied back.

Fan hazard. To avoid personal injury, keep hands clear and loose clothing tied back. Always

disconnect all power sources before performing maintenance or service procedures.

Laser hazard. To avoid personal injury, avoid eye or skin exposure to direct or scattered

r

adiations.

Safety precautions

CP2315-RGB User Guide 14

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Voltage hazard. To avoid personal injury, always disconnect all power sources before

performing maintenance or service procedures.

Not for household use.

Mandatory action

Consult the service manual.

Disconnect all power sources before performing maintenance or service procedures.

Electrical labels

Indicates the presence of a protective earth ground.

Indicates the presence of an earth ground.

Additional hazard labels

Indicates Class 4 laser radiation when open. Avoid eye or skin

exposure to direct or scattered r

adiation.

CLASS 1 LASER PRODUCT IEC 60825-1

W

avelengths: 450 nm - 656 nm

FDA laser variance (US projectors only)

Safety precautions

CP2315-RGB User Guide 15

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Indicates a light hazard. Do not look directly into the lens. The

extreme high brightness can cause permanent ey

e damage. Class 1

Laser Product - Risk Group 3 according to IEC 60825-1:2014 and

IEC 62471:2006

Indicates high leakage current. Earth connection essential before

connecting the power supply

.

Indicates a light hazard. Do not look directly into the lens. The

extreme high brightness can cause permanent ey

e damage.

Safety precautions

CP2315-RGB User Guide 16

020-102768-03 R

ev. 1 (09-2019)

Copyright

©

Introduction

This manual is intended for oper

ators of Christie CP2315-RGB projection systems.

For complete production documentation and technical support, go to www.christiedigital.com.

Product documentation

For installation, setup, and user information, see the product documentation available on the Christie

Digital Systems USA Inc. website. Read all instructions before using or servicing this product.

1. Access the documentation from the Christie website:

• Go to http://bit.ly/2JVe2ln or

https://www.christiedigital.com/en-us/cinema/cinema-products/digital-cinema-projectors/

christie-cp2315-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

2. On the product page, select the model and switch to the Downloads tab

.

Christie CP2315-RGB User manual

Christie CP2315-RGB User manual

Related papers

Other documents