Eurotech CPU-521-17 Owner's manual

User Manual

CPU-521-17

Mini-ITX Industrial Single Board Computer

Rev. 0-3 — 5 June 2017 — CPU-521-17_UserMan_EN_0-3 — ENGLISH

Preliminary

Trademarks

All trademarks, registered trademarks, logos, trade names and products names contained in this

document are the property of their respective owners.

Intended audience of this document

This document is intended for system integrators: skilled persons with a thorough knowledge in linking

together different computing systems and software applications physically or functionally, to operate as a

coordinated whole, in compliance with the applicable regulations.

Revision history

Revision Description Date

0-3 Preliminary release 5 June 2017

Preliminary

CPU-521-17User Manual Rev. 0-3 Contents

CONTENTS

Trademarks 2

Intended audience of this document 2

Revision history 2

Contents 3

1 Safety instructions 5

1.1 Safety messages used in this document 5

1.2 How to prevent electrostatic discharge 6

1.3 How to prevent electrical hazards 6

2 How to receive technical assistance 7

2.1 How to ask for technical support 7

2.2 How to send a product for repair 7

3 Declaration of conformity 9

3.1 CE Marking 9

3.2 WEEE compliance 9

3.3 RoHS compliance 9

4 Before using the product 11

5 Product Specifications 13

6 Hardware Installation 15

6.1 Board Layout 15

6.2 System Memory 16

6.2.1 Features 16

6.2.2 Installing the DIMM Module 17

6.3 Jumper Settings 19

6.3.1 Clear CMOS Data 19

6.3.2 Auto Power-ON Selection 20

6.3.3 LVDS Panel Power Selection 21

6.3.4 LCD/Inverter Power Selection 22

6.3.5 LVDS Back-light Power Selection 23

6.3.6 COM1 and COM2 RS232/Power Selection 24

6.3.7 Mini PCIe / mSATA Signal Selection 25

6.4 Rear Panel I/O ports 26

6.4.1 12V DC-in port 27

6.4.2 Video ports 28

6.4.2.1 DP Port 28

6.4.2.2 HDMI Port 28

6.4.2.3 Driver installation 28

6.4.3 RJ45 LAN ports 29

6.4.3.1 Features 29

6.4.3.2 Driver installation 29

6.4.4 USB ports 30

6.4.4.1 BIOS Settings 30

6.4.4.2 Driver installation 30

6.4.4.3 Wake-On-USB Keyboard/Mouse 31

6.4.5 Audio Ports 32

6.4.5.1 Rear Audio 32

6.4.5.2 BIOS Settings 32

3 / 50

Preliminary

Contents CPU-521-17User Manual Rev. 0-3

6.4.5.3 Driver installation 32

6.5 I/O Connectors 33

6.5.1 Digital I/O Connector. Digital I/O Power Connector 33

6.5.2 SATA (Serial ATA) Connectors 34

6.5.2.1 Features 34

6.5.2.2 BIOS Settings 34

6.5.3 SATA (Serial ATA) Power Connectors 35

6.5.4 COM Connectors 36

6.5.5 Front Panel Connectors 37

6.5.5.1 HDD-LED connector (for a Hard Drive LED) 37

6.5.5.2 RESET-SW connector (for a reset switch) 37

6.5.5.3 PWR-BTN connector (for a power switch) 37

6.5.5.4 PWR-LED connector (for a power/standby LED) 37

6.5.6 Cooling Fan Connectors 38

6.5.6.1 BIOS Settings 38

6.5.7 LVDS LCD Panel Connector and LCD/Inverter Power Connector 39

6.5.7.1 LVDS LCD Panel Connector Pinout: 40

6.5.7.2 LCD/Inverter Power Connector Pinout 40

6.5.8 S/PDIF Connector 41

6.5.9 SMBus Connector 42

6.5.10 Expansion Slots 43

6.5.11 Chassis Intrusion Connector 44

6.5.12 LPC Connector 45

6.5.12.1 Connecting the INT-342-10 board 46

6.5.13 Power ON LED 47

6.5.14 Battery Connector 48

6.5.14.1 Battery Safety Instructions 48

Notes 49

4 / 50

Preliminary

CPU-521-17User Manual Rev. 0-3 1 Safety instructions

1 SAFETY INSTRUCTIONS

READ CAREFULLY AND UNDERSTAND THE INSTRUCTIONS AND WARNINGS CONTAINED

IN THIS DOCUMENT BEFORE INSTALLING / USING THE PRODUCT.

KEEP THIS DOCUMENT FOR FUTURE REFERENCE.

To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the instructions

and warnings contained in this document.

Failure to comply with the instructions and warnings contained this document, violates the standards of

safety, design, manufacture, and intended use of the product.

Eurotech assume no liability for any damage caused by failure to observe the instructions and warnings

contained this document.

Whenever you have any doubt regarding the correct understanding of this document, contact the Eurotech

Technical Support (for more information see "How to receive technical assistance" on page7).

1.1 Safety messages used in this document

DANGER

INDICATES A HAZARD WITH A HIGH LEVEL OF RISK WHICH, IF NOT AVOIDED, WILL

RESULT IN DEATH OR SERIOUS INJURY

WARNING

INDICATES A HAZARD WITH A MEDIUM LEVEL OF RISK WHICH, IF NOT AVOIDED, COULD

RESULT IN DEATH OR SERIOUS INJURY

CAUTION

INDICATES A HAZARD WITH A LOW LEVEL OF RISK WHICH, IF NOT AVOIDED, COULD

RESULT IN MINOR OR MODERATE INJURY

NOTICE

Indicates practices not related to personal injury, such as:

l An instruction to follow to use the product effectively

l An instruction to follow to avoid damaging the product or third-party property

5 / 50

Preliminary

1 Safety instructions CPU-521-17User Manual Rev. 0-3

1.2 How to prevent electrostatic discharge

NOTICE

HOW TO PREVENT ELECTROSTATIC DISCHARGE

The symbol on the left is applied on electrostatic-sensitive devices (ESD).

To prevent electrostatic discharge:

l Handle the electrostatic-sensitive devices in an ESD-protected area

l Observe the appropriate antistatic precautions. For example: use a wrist

strap kept in constant contact with bare skin and attached to ground.

1.3 How to prevent electrical hazards

Before supplying power to the product, observe all the instructions for safety, installation, and

operation

DANGER

Failure to supply power correctly and failure to follow all safety instructions, may create an

electric shock hazard, which could result in personal injury or loss of life, and may damage the

product or other property.

To prevent electrical hazards:

l Before using the product, carefully read the supplied instructions

l Never operate with wet hands

l Check any power cords for damage before using them

l Use certified power cables. The power cables must meet the power requirements of the

device

l Position cables with care. Avoid positioning cables in places where they may be

trampled or compressed by objects placed on them

l Verify that power-points and plugs are not damaged. Avoid overloads

l Always disconnect power and discharge the circuits before touching them

l Use a power supply that meets the requirements stated on the identification label of the

product. In case of uncertainties about the required power supply, contact the Eurotech

Technical Support Team (for more information see "How to receive technical assistance"

on page7).

6 / 50

Preliminary

CPU-521-17User Manual Rev. 0-3 2 How to receive technical assistance

2 HOW TO RECEIVE TECHNICAL ASSISTANCE

2.1 How to ask for technical support

To ask for technical support, complete the following steps

1. Go to the Eurotech Global Support Centre: https://support.eurotech.com/

2. Submit a support request

3. Wait for the reply from the Support Team with the information you required

2.2 How to send a product for repair

To send a product for repair, complete the following steps:

1. Go to the Eurotech Global Support Centre: https://support.eurotech.com/

2. Submit an RMA request

3. Wait for the reply from the RMA Department. It will contain:

l The RMA number

l The shipping information

4. Pack the product adequately using anti-static material and place it in a sturdy box with enough

packing material to protect it from shocks and vibrations

5. Ship the product to Eurotech following the information received from the RMA Department.

NOTICE

Any product returned to Eurotech, that is found to be damaged due to inadequate packaging,

will not be covered by the warranty.

7 / 50

Preliminary

(This page has been intentionally left blank)

Preliminary

CPU-521-17User Manual Rev. 0-3 3 Declaration of conformity

3 DECLARATION OF CONFORMITY

3.1 CE Marking

This product is CE marked.

The product meets the guidelines listed in the following sections.

Eurotech is not responsible for the use of this product together with equipment (e.g. power

supplies, personal computers, etc.) that are not CE marked and compliant with the

requirements specified in this document.

3.2 WEEE compliance

In compliance with the Directive 2012/19/EU of the European Parliament and of the Council

of 4 July 2012 on waste electrical and electronic equipment (WEEE), the symbol on the

right, shown on the product or within its literature, indicates separate collection for electrical

and electronic equipment (EEE) that has been placed on the market after 2005.

The product described in this document, at the end of its life cycle, must be collected

separately and managed in accordance with the provisions of the current Directive on waste

of electrical and electronic equipment.

Because of the substances present in the product, improper disposal can cause damage to

human health and to the environment.

To avoid any possible legal implications, contact your local waste collection body for full

collect and recycling information.

3.3 RoHS compliance

The product described in this document, including all its components and its sub-assemblies, have been

manufactured in compliance with the Directive 2011/65/EU of the European Parliament and of the Council

of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic

equipment.

9 / 50

Preliminary

(This page has been intentionally left blank)

Preliminary

CPU-521-17User Manual Rev. 0-3 4 Before using the product

4 BEFORE USING THE PRODUCT

Before using the product, setup the following components:

l RAM module

l Storage device (for example a hard disk drive)

l Keyboard

l Mouse

l Display.

11 / 50

Preliminary

(This page has been intentionally left blank)

Preliminary

CPU-521-17User Manual Rev. 0-3 5 Product Specifications

5 PRODUCT SPECIFICATIONS

Specifications Description

System Processor 6th Generation Intel® CoreTM Processors, BGA 1356

Intel® CoreTM i7-6600U Processor, Dual Core, 4M Cache, 2.6GHz (3.4GHz), 15W

Intel® CoreTM i5-6300U Processor, Dual Core, 3M Cache, 2.4GHz (3.0GHz), 15W

Intel® Celeron® Processor 3955U, Dual Core, 2M Cache, 2.0GHz, 15W

Memory Two 204-pin SODIMM up to 16GB

Dual Channel DDR3L 1600MHz

BIOS Insyde SPI 128Mbit

Graphics Controller Intel® HD Graphics GT Series

Feature OpenGL 4.4, DirectX 12, OpenCL 2.1

HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265,

VP8, VP9

HW Encode: AVC/H.264, MPEG2, JPEG, HEVC/H265, VP8, VP9

Display 1x LVDS

1x HDMI

1x DP++

LVDS: dual channel 48-bit, resolution up to 1920x1200 @ 60Hz

DP: resolution up to 4096x2304 @ 60Hz

HDMI: resolution up to 2560x1600 @ 60Hz or 4096x2160 @ 24Hz

Triple

Displays

LVDS + HDMI + DP++

Expansion Interface 1x PCIe x4 (Gen 3)

1x SIM

1x Full-size Mini PCIe (PCIe/USB/SATA)

1x Full-size Mini PCIe (PCIe/USB)

Audio Audio Codec Realtek ALC888S-VD2-GR

Controller 1x Intel® I210AT PCIe (10/100/1000Mbps)

1x Intel® I219LM PCIe with iAMT11.0 (10/100/1000Mbps) -

(only Core i7/i5 supports iAMT)

Ethernet Ethernet 2 x Gigabit Ethernet (RJ-45)

Rear I/O USB 4x USB 3.0

Display 1x HDMI

1x DP++

Audio 1x Line-out

1x Mic-in

(Continued on next page)

13 / 50

Preliminary

5 Product Specifications CPU-521-17User Manual Rev. 0-3

(Continued from previous page)

Specifications Description

Internal I/O Serial 2x RS-232/422/485 (RS-232 w/ power) (2.0mm pitch)

2x RS-232 (2.0mm pitch)

USB 4x USB 2.0 (2.0mm pitch)

Display 1x LVDS LCD Panel Connector

1x LCD/Inverter Power

Audio 1x S/PDIF

SATA 2x SATA 3.0 (up to 6Gb/s)

2x SATA Power

RAID 0/1

DIO 1x 8-bit DIO

LPC 1x LPC

SMBUS 1x SMBus

WatchDog

Timer

Output &

Interval

System Reset, Programmable via Software from 1 to 255 Seconds

Security TPM Factory option

Power Type Single 12V +/-10% DC

Connector DC-in Jack

Right Angle Connector (4-pin) (factory option)

Vertical Type Connector (4-pin) (factory option)

Consumption Typical: 6600U:12V @ 0.98A (11.76 W); 6300U:12V @ 0.95A (11.40 W)

Max: 6600U:12V @ 1.62A (19.44 W); 6300U:12V @ 1.58A (18.96 W)

RTC Battery Lithium 3V (210mAH)

OS Support Microsoft/Linux Board Support Package for CPU-163-15 Development Kits:

l Windows 10 IoT Enterprise

l CentOS

Support for custom carriers (Prof. Services):

l Fedora/CentOS

l Debian

l Win 10 IoT Enterprise

l RedHat® Enterprise Linux

Environment Temperature Operating:

l -20°C to +70°C

l Factory option: 0°C to +60°C

Storage:

l -40 to 85°C

Humidity Operating: 5 to 90% RH

Storage: 5 to 90% RH

Mechanical Dimensions Mini-ITX Form Factor

170mm (6.7") x 170mm (6.7")

Height PCB: 1.6mm

Top Side: 16.5mm, Bottom Side: 3.5mm

14 / 50

Preliminary

CPU-521-17User Manual Rev. 0-3 6 Hardware Installation

6 HARDWARE INSTALLATION

6.1 Board Layout

15 / 50

Preliminary

6 Hardware Installation CPU-521-17User Manual Rev. 0-3

6.2 System Memory

NOTICE

Before installing any devices, turn OFF the board and unplug the power cord.

Failure to do so will cause severe damage to the board and components.

6.2.1 Features

l Two 204-pin DDR3L SODIMM sockets

l Supports 1600MHz DDR3L SDRAM

l Supports up to 16GB system memory

l Supports dual channel memory interface

The system board supports the following memory interfaces:

Single Channel (SC) Data will be accessed in chunks of 64 bits (8B) from the memory channels

The DIMMs are on the same channel.

DIMMs in a channel can be identical or different. We recommend using

identical DIMMs.

You don't need to populate all slots.

Dual Channel (DC) Data will be accessed in chunks of 128 bits from the memory channels. Dual

channel provides better system performance because it doubles the data

transfer rate.

DIMMs of the same memory configuration are on different channels.

16 / 50

Preliminary

CPU-521-17User Manual Rev. 0-3 6 Hardware Installation

6.2.2 Installing the DIMM Module

The system board used in the following illustrations may not resemble the actual board. These

illustrations are for reference only.

To install the DIMM Module, complete the following steps

1. Make sure the PC and all other peripheral devices connected to it has been powered down

2. Disconnect all power cords and cables

3. Locate the SODIMM socket on the system board.

Note the key on the socket. The key ensures the module can be plugged into the socket in only one

direction.

17 / 50

Preliminary

6 Hardware Installation CPU-521-17User Manual Rev. 0-3

4. Grasping the module by its edges, align the module into the socket at an approximately 30 degrees

angle. Apply firm even pressure to each end of the module until it slips down into the socket. The

contact fingers on the edge of the module will almost completely disappear inside the socket

5. Push down the module until the clips at each end of the socket lock into position. You will hear a

“click”, indicating the module is correctly locked into position

18 / 50

Preliminary

CPU-521-17User Manual Rev. 0-3 6 Hardware Installation

6.3 Jumper Settings

6.3.1 Clear CMOS Data

If you encounter the following situations:

l CMOS data becomes corrupted

l You forgot the supervisor or user password

you can reconfigure the system with the default values stored in the ROM BIOS.

To load the default values stored in the ROM BIOS, complete the following steps:

1. Power-OFF the system and unplug the power cord

2. Set pins 2 and 3 of the jumper to ON. Wait for a few seconds and set the jumper back to the default

setting: pins 1 and 2 to ON

3. Plug the power cord and power-ON the system.

19 / 50

Preliminary

6 Hardware Installation CPU-521-17User Manual Rev. 0-3

6.3.2 Auto Power-ON Selection

To select the method of powering on the system use JP16:

l To power-on whenever AC power comes in, set JP16 pins 2 and 3 to ON

l To use the power button, set pins 1 and 2 to ON

When using the JP16 “Power ON” feature to power the system back on after a power failure occurred, the

system may not power ON if the power lost is resumed within 5 seconds (power flicker).

20 / 50

Preliminary

Page is loading ...

Eurotech CPU-521-17 Owner's manual

Eurotech CPU-521-17 Owner's manual

Related papers

Other documents