Owner’s Manual
™
WATCH THE VIDEO
Model #710
IMPORTANT: READ THE OWNER’S MANUAL BEFORE ASSEMBLING
1161 SOUTH PARK DRIVE, KERNERSVILLE NC 27284
LIBERTY GARDEN PRODUCTS, INC.
VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM
OR CALL US TOLL FREE AT 1-866-820-5805, MONDAY - FRIDAY 9 A.M. - 5 P.M. EST
PARTS LIST
A
2
C
B D
A. Crank handle (1) B. Leader hose (1) C. Base shelf (1) D. Hose reel (1)
IMPORTANT: LAY OUT ALL PARTS AND FASTENERS. MAKE SURE ALL PARTS ARE
ACCOUNTED FOR. IF ANY PART IS MISSING PLEASE CONTACT LIBERTY GARDEN PRODUCTS
AT 1-866-820-5805. DO NOT CONTACT THE RETAILER. YOU CAN ALSO VISIT OUR
WEBSITE, WWW.LIBERTYGARDENPRODUCTS.COM, FOR MORE INSTRUCTIONS, PICTURES
AND HELPFUL HINTS.
TOOLS REQUIRED:
HARDWARE INCLUDED
BB
AA
CC
AA. Allen wrench (Supplied)
Adjustable
Wrench
Stud
Finder
Hammer
Drill
Electric
Drill
Phillips
screwdriver
or bit for an
electric drill
7/16 in. and
3/8 in. Socket
and Socket
wrench
BB. Allen bolts (3)
DD
DD. Allen screw (1)CC. Lock nuts (3)
Note: Hardware not shown to actual size.
Estimated Assembly Time : 10 minutes (not including mounting the hose reel)
PRE-ASSEMBLY
The wall mounting hardware is NOT included with this unit. Check with the retailer or visit a hardware store to purchase.
TIP: Remember to use the correct size and quantity of hardware to properly support the
total weight of the unit. A standard 100' length of garden hose weighs approximately 15 lbs.
Filled with water, the additional weight can exceed 20 lbs. The mounting hardware must be
able to support the combined weight of the unit, garden hose, plus water.
The following hardware (not included)
is recommended for installation:
1. BRICK OR MASONRY ANCHOR SLEEVES
(2) 7 or 8 mm x 60 mm masonry wall anchors (5/16” x 2 1/2”)
(2) Anchor sleeves
(2) Washers
(2) Lock washers
(2) Nuts
The following hardware (not included) is recommended for installation:
3. WOOD SCREWS
(2) 7 or 8 mm x 60 mm wood screws (5/16” x 2 1/2”)
(2) Washers
The following hardware (not included)
is recommended for installation:
2. BRICK OR MASONRY SCREWS
(2) 7 or 8 mm x 60 mm masonry screws (5/16” x 2 1/2”)
(2) Washers
• Position and hold your hose reel against the brick/masonry wall
at a convenient height. Mark the position of each suspension
hole on the wall. Remove the hose reel.
• Insert the masonry wall anchors into the anchor sleeve. Next,
insert the anchor and sleeve into the drilled holes until the steel
sleeve is completely in the wall.
• Place the hose reel on the masonry wall anchors.
• Install a washer, lock washer, and nut over each
wall anchor and tighten securely.
• Using a stud finder, locate the wood studs on your wall.
• Position and hold your hose reel against the wood wall at a convenient height.
Mark the position of each suspension hole on the wall. Remove the hose reel.
• Align the hose reel suspension holes with the pilot holes.
• Attach the hose reel to the wall using the wood screws with washers and tighten securely.
To learn more, watch a video on our warranty and care section @ www.libertygardenproducts.com
NOTE: Drill hole diameters
may vary based on anchor
sleeve, concrete screw, and
wood screw manufacturer.
Check product recommendations
before drilling holes.
• Position and hold your hose reel against the brick/masonry
wall at a convenient height. Mark the position of each
suspension hole on the wall. Remove the hose reel.
• Align the hose reel suspension holes with the pilot holes.
• Attach the hose reel to the wall using the concrete screws
with washers and tighten securely.
• Using a hammer drill, drill holes 5/16” in diameter at the
marked positions on the wall.
• Using an electric drill, drill pilot holes 1/4” in diameter at the marked positions on the wall.
• Using a hammer drill, drill pilot holes 1/4” in diameter at the
marked positions on the wall.
3
INSTALLATION
This hose reel must be mounted to a solid masonry wall or to wall studs
Mounting Hole
Size: 1/4”
Mounting Hole
Size: 1/4”
Mounting Hole
Size: 5/16”
C
C
C
4
ASSEMBLY
1
3
Attach the hose reel (D) to the base shelf
(C) by hanging the reel on the small slot
located at the front of the base.
Line up the holes in the hose reel (D) with
the base shelf (C) and insert long Allen
bolts (BB)
2
Tighten Allen bolts (BB) with the
supplied Allen wrench (AA) at the
same time using fingers screw on
lock nuts (CC) to secure base
shelf (C) to hose reel (D)
Pliers (not included) may be
needed to hold and tighten lock
nuts.
CAUTION: DO NOT OVER
TIGHTEN LOCK NUTS AND
ALLEN BOLTS.
FIGURE 1
FIGURE 2
FIGURE 3
D
C
C
C
BB
D
CC
D
BB
5
ASSEMBLY
4
FIGURE 4
FIGURE 5
FIGURE 6
Align the holes in the crank handle (A) with
the crank handle shaft on the hose reel (D).
Insert the short Allen screw (DD) into the
crank handle and tighten with supplied Allen
wrench (AA)
5
6
Attach leader hose (B) to swivel connector on
the hose reel (D). Attach end of leader hose
to water source.
Attach your garden hose to the hose connector on the
hose reel (D). The hose is now ready to wind around the
spool. The Navigator holds up to 125 ft. of 5/8” garden
hose.
A
AA
DD
D
B
D
D
6
OPERATING INSTRUCTIONS
1
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
Pull up on handle knob located on the base shelf (C) then
rotate hose reel (D) to one of the eight locking positions.
3
Release the handle on the base shelf (C) and lock unit into
one of the desired positions. Your Navigator rotating hose
reel is now ready for use.
4
Located at the bottom of the base spool (D) near the crank
handle is a pre-assembled Allen screw. Using the supplied
Allen wrench (AA) tighted or loosen tension on the spool.
To increase the tension, tighten the screw, to reduce
tension, loosen the screw.
2
Pull up on the handle knob located on the base
shelf (C) and turn the locking pin to the up position.
The Navigator rotating hose reel will now turn a full
360 degrees.
D
TIP: Keep reel in the locked position when winding garden hose.
C
D
D
AA
C
C
7
CARE INSTRUCTIONS
NOTE
It is recommended that the hose reel (D) be taken
off and stored indoors or sealed in a plastic container
for winter protection.
D
.
When you install your hose reel, be sure the hose washers are in place and all fittings are secure. If you live
in more temperate climates, be sure to drain the unit of any residual water before storing.
• DO NOT EXPOSE UNIT TO FREEZING TEMPERATURES while water remains in the plumbing system,
this can damage the swivel.
• DO NOT leave water running through the hose reel cart while not in use or unsupervised.
• DO NOT consume water from garden hose; not fit for human consumption.
WARNING! This product contains one or more chemicals known in the state of California to cause
cancer and birth defects or reproductive harm. Wash hands after handling.
Your hose reel is manufactured with the finest quality components available. This product will give
you many seasons of reliable and functional hose storage. All components are manufactured to rigorous
quality standards not common in other consumer grade hose reels available today. As with any steel
product, there is always the chance for rust developing over time. Your hose reel finish is designed for
industrial applications, but even the toughest of coatings can be compromised by scratches. Such
minor surface damage can occur in shipping despite our best efforts. We have found that most scratches
occur during assembly and/or installation (in the case of wall mounted hose reels). If the base metal is
exposed to the elements long enough, rust will develop. In the case of wall mounted reels, be sure to use
stainless steel mounting hardware. We recommend that you periodically inspect your reel for any surface
damage. Scratches can easily be repaired by using standard automotive touch-up body paint. Some of our
most loyal customers recommend that at the end of each season, the unit be cleaned and painted with a
clear acrylic paint.
5
TROUBLE SHOOTING GUIDE
Problem: Swivel head is not rotating, causing the leader hose to kink up.
Solution: Remove leader hose and turn the square head of the swivel several times; apply lubricant.
Problem: Your new Liberty hose reel is leaking at the swivel.
Solution: Apply Teflon/Plumber's Tape on the threads or/and make sure fixtures are tightened. It is
normal for the swivel to leak slightly until the O-rings are wet and have seated. If the leaking continues,
try these steps: (It is not necessary to return the hose reel)
1. If the leader hose is attached to the swivel, unscrew the hose and look inside the swivel.
2. Check that the hose washer is inside the nut. You may contact Liberty Garden Products for a new
hose washer or obtain one at any hardware store.
3. If your swivel is old, the O-rings may be worn, please contact us for a new set of O-rings.
4. If these steps do not solve your leaking problem, contact Liberty Garden Product’s customer service.
CALL US AT 1-866-820-5805 IF YOU HAVE ANY QUESTIONS
REGARDING TROUBLESHOOTING AND MAINTENANCE
SHAFT O-RING HOUSING O-RING
SNAP RING
WASHER
INSERT
O-RING
NUT
9
LIBERTY GARDEN PRODUCTS LIMITED WARRANTY
(Effective October 13, 2016)
This limited warranty is applicable to each original end-customer (hereinafter “Customer”) purchasing the model the model 710 decorative
Navigator
TM rotating hose reel consisting of the structural metal frame and spool (hereinafter the “Structural Frame”) and various other
non-frame components (hereinafter the “Non-Frame Parts”) sold by Liberty Garden Products, Inc. (hereinafter “Company”) for Customer’s
own use and not for resale. The Structural Frame and Non-Frame Parts are collectively referred to herein as the “Products”.
1. LIMITED WARRANTY; EXCLUSIVE REMEDIES:
1.1. LIMITED WARRANTY ON PRODUCTS:
Company warrants solely to the original Customer that (a) the Structural Frame will be free
from defects in materials and workmanship under normal use for a period of three (3) YEAR(S) from the date of original retail purchase, and (b)
the Non-Frame Parts (which consist of the crank handle, swivel and water connections, leader hose and tires), will be free from defects in materials
and workmanship under normal use for a period of ONE (1) YEARS from the date of original retail purchase. Notwithstanding the foregoing, the
colors and finishes of the Products may vary within a reasonable scope due to unavoidable color variations in different production batches, and
such variations shall not constitute a material defect. This limited warranty is limited solely to the original Customer with proof of purchase and is
not transferable.
1.2. THE WARRANTY: During a covered Product’s limited warranty period, Company will, at Company’s sole option and discretion, (1) repair
the defective component or product without charge or (2) replace the defective component or product without charge.
1.3. The foregoing limited warranty is subject to the Customer’s proper storage, transportation, handling and use of the Products as the same are
defined within Company’s then-current published guides and instructions for use and care. The limited warranty does not include defects due to
normal wear and tear, abuse or misuse, mishandling, neglect, accident, fire, lightning, sunlight or other natural hazard, delivery or transportation
damage, failure to follow applicable directions or instructions, or improper or inadequate cleaning, maintenance, care, repairs, modifications, or use
beyond a Product’s intended use. Please note that since the Structural Frame is made from steel rust may occur over time. As such, this limited
warranty does not include rust or defects due to the same.
1.4. LIMITED WARRANTY CLAIMS PROCEDURE: To obtain performance under this limited warranty, Customer shall notify Company in
writing (to Liberty Garden Products, Inc., 1161 South Park Drive, Kernersville, NC 27284, Attn: Customer Service / Warranty Department), by email
(to [email protected]), or by telephone (to (336) 992-3595) with a full description of the defect that is covered by
warranty and a copy of the dated proof of purchase of the applicable product.
• Company shall review each such claim and issue Customer a return merchandise authorization (“RMA”) in the event that the described defect or
condition merits warranty review as determined by Company. Customers who have been issued a RMA shall, at Company’s election, return the
covered item to the same physical address listed above for reporting initial claims. Company shall not accept any returned product without a RMA.
• Upon receipt, Company will evaluate the returned product(s) to determine if there is a warranty claim and, if so, how Company wishes to remedy
the same. During a covered product’s respective limited warranty period, Company will, at Company’s sole and absolute option and discretion,
(1) repair the defective component or product without charge or (2) replace the defective component or product without charge. Refunds are not
available pursuant to this limited warranty.
• Customer is solely responsible for transportation of the covered product(s) to the Company for evaluation (if applicable and requested by
Company). In the event that Company determines that a claim under this limited warranty is justified, Company shall be responsible for
transportation of the repaired, corrected, replaced or exchanged product back to Customer. Customer shall be solely responsible for the
transportation of any product back to Customer if Company determines that a claim under this warranty is not justified.
• Any repaired, corrected, replaced or exchanged Products shall be subject to the Limited Warranty set forth to the duration of the original limited
warranty period as set forth in Section 1.1. and not for any extended duration, following their repair, correction, replacement or exchange.
1.5. IF A COMPANY PRODUCT DOES NOT CONFORM TO THESE LIMITED WARRANTIES, THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY IS, AT COMPANY’S SOLE AND EXCLUSIVE OPTION, THE (1) REPAIR OF ANY DEFECTIVE PRODUCT
OR COMPONENT PART OR (2) REPLACEMENT OF ANY DEFECTIVE PRODUCT OR COMPONENT PART. THE LIMITED
WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND MADE IN LIEU OF ALL OTHER WARRANTIES,
REMEDIES, RIGHTS OR CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED, EITHER IN FACT OR BY
OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. COMPANY SPECIFICALLY DISCLAIMS, WITHOUT LIMITATION, ANY AND ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND. IF COMPANY CANNOT LAWFULLY DISCLAIM IMPLIED
WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF
THIS LIMITED WARRANTY.
The Company does not assume or authorize any person to assume for them any other liability in connection with the
Products.
10
LIBERTY GARDEN PRODUCTS LIMITED WARRANTY CONTINUED
2. EXCLUSION AND LIMITATION OF LIABILITY:
IN NO EVENT, WHETHER BASED ON CONTRACT OR TORT OR OTHER LEGAL THEORY, SHALL COMPANY BE
LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT
NOT LIMITED TO, DAMAGES TO OTHER PROPERTY, INCONVENIENCE, DAMAGES FOR LOSS OF PROFITS,
REVENUE, GOODWILL OR USE, INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN
CONTRACT, TORT, STRICT LIABILITY, OR IMPOSED BY STATUTE, OR OTHERWISE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages or
exclusions or limitations on the duration of implied warranties or conditions, so the above limitations or exclusions may not apply to Customer. In
jurisdictions that limit the scope of or preclude limitations or exclusion of remedies or damages, or of liability, such as liability for gross negligence
or willful misconduct or do not allow implied warranties to be excluded, the limitation or exclusion of warranties, remedies, damages or liability set
forth above are intended to apply to the maximum extent permitted by applicable law. This limited warranty gives the Customer specific legal rights,
and the Customer may also have other rights that vary by state, country or other jurisdiction.
3. SEVERABILITY:
If any provision of this limited warranty is held to be illegal, invalid or otherwise unenforceable, such provision will be enforced to the extent possible
consistent with its stated intention, or, if incapable of such enforcement, will be deemed to be severed and deleted from this limited warranty, while
the remainder of the terms of this limited warranty will continue in full force and effect.
4. DISPUTE RESOLUTION:
ThisLiberty Garden Products, Inc. Limited Warranty shall be governed by and construed in accordance with the laws of the State of North
Carolina, without regard to its principles of conflicts of law. The parties acknowledge the exclusive jurisdiction of the federal and state courts of the
State of North Carolina. Any claims or disputes under this
Liberty Garden Products, Inc. Limited Warranty shall be heard exclusively in any state
or federal courts sitting in Guilford County, North Carolina, and both parties expressly consent to the personal jurisdiction and venue of the North
Carolina state and federal courts for such actions.
Updated 10/13/2016
™
“Liberty” is a registered trademark of Liberty Garden Products, Inc. Kernersville, NC. All Rights Reserved 2016
/
