Renkforce 7+2 ports USB 3.0 hub + quick-charge port, + LED indicator lights Owner's manual

Brand: Renkforce

Model: 7+2 ports USB 3.0 hub + quick-charge port, + LED indicator lights

Category: Coffee making accessories

Type: Owner's manual

Page is loading ...

First, switch off the mains voltage to the mains socket to which the power

adapter/power cable is connected (switch off at the corresponding circuit

breaker or remove the safety fuse and then switch off at the RCD protec-

tive switch, so that the socket is fully disconnected from the mains volt-

age).

Then you can remove the mains plug from the mains socket. Dispose of

the damaged power adaptor/power cable in an environment-friendly way;

do not use it any more. Replace it by a power supply unit / power cable of

the same design.

c) Operation

• This product is not a toy. Devices operated using mains voltages should

not be used by children. Therefore, be especially careful when children

are around.

Use the product where it is out of reach of children.

• The product is intended for use only in dry, enclosed indoor locations. No

part of the product should become damp or wet; never handle it if your

hands are wet!

With the power adapter/power cable there is also a risk of a potentially

fatal electric shock!

• When setting up the product, make sure that the cables are neither kinked

nor pinched.

• Do not apply force when connecting the USB plugs. A USB plug ﬁts in the

USB socket only on one of its sides.

• Never use the product immediately after it has been taken from a cold

room into a warm one. The condensation that forms can destroy the prod-

uct under certain circumstances. Power supply unit / power cable also

have an associated risk for electric shock!

Allow the product to reach room temperature before connecting it to the

power supply and putting it to use. This may take several hours.

• Avoid the following adverse conditions at the location of installation and

during transport:

- Dampness or excessive humidity

- Extreme cold or heat, direct sunlight

- Dust or ﬂammable gases, fumes or solvents

- Strong vibrations, impacts or blows

- Strong magnetic ﬁelds such as those found in the vicinity of machinery

or loudspeakers

Assembly

The USB3.0 hub can be mounted to a work desk or wall (distance between screws

114 mm) with the openings at the bottom.

Use screws and, if necessary, screw anchors that are suitable for the sur-

face.

When mounting on a wall, make sure that no cables or wires are damaged

when drilling or screwing.

Connection and start-up

• Connect the circular low-voltage plug of the power adapter into the corresponding

socket of the USB3.0 hub.

• Connect the power adapter to a standard mains socket using the power cable en-

closed.

• Connect the USB3.0 hub via the enclosed USB cable to a free USB3.0 port on your

computer. The computer does not need to be switched off.

• Switch the USB3.0 hub on with the large, triangular pushbutton.

Upon ﬁrst use, the operating system will detect the new hardware and automatically

install the required drivers; they are already present in the operating system.

Please note:

When the USB3.0 hub is switched off, all USB ports and also the two USB

charging ports are functionless.

• Connect your USB devices to the USB ports labelled “1” to “7” at the front of the

USB3.0 hub. When a USB device was detected, the corresponding LED at the

USB3.0 hub lights up.

Of course, you can also connect USB2.0 and USB1.1 devices at the USB3.0

hub.

Depending on the USB device, the operating system detects new hardware and

installs the required drivers. Please refer to the operating instructions of the USB

device to know how to do this.

For example, Windows already uses its own drivers for many devices, such as for

USB ﬂash drives, USB mice, etc.

Operating instructions

7+2 Port USB3.0 Charging Hub

Item no. 1268678

Intended use

The product is designed for connection to a computer with a USB3.0 interface in order

to provide additional USB3.0 ports.

Furthermore, the USB3.0 hub has two power output that are suitable for charging of

suitable devices (e.g. smartphones, or tablets, iPad, etc.).

Openings at the bottom allow mounting of the USB3.0 hub e.g. below a work desk or

shelf or on a wall.

A standard power unit is used to supply the power.

Always observe the safety instructions and all other information included in these op-

erating instructions.

This product complies with the applicable national and European requirements. All

names of companies and products are the trademarks of the respective owners. All

rights reserved.

Package contents

• USB3.0 Hub

• Power adapter

• Power cable

• USB cable

• Operating instructions

Explanation of symbols

The lightning symbol inside a triangle is a warning to inform you of potential

risks of personal injury, such as electric shock.

This symbol indicates speciﬁc risks associated with handling, function or

use.

The “arrow” symbol indicates special tips and operating information.

Safety instructions

Damage due to failure to follow these operating instructions will void the

warranty! We do not assume any liability for any resulting damage!

We do not assume any liability for material and personal damage caused

by improper use or non-compliance with the safety instructions. In such

cases, the warranty will be null and void.

a) General

• The unauthorised conversion and/or modiﬁcation of the product is not

permitted for safety and approval reasons (CE). Never dismantle the prod-

uct.

• Any maintenance or repair work may only be performed by an expert.

• Do not leave packaging material carelessly lying around, since it could

become a dangerous plaything for children.

b) Power adapter/power cable

• The design of the power adapter complies with safety class II. Only use a

standard mains socket as the voltage source for the power adapter.

• The mains socket into which the power cable is plugged must be easily

accessible.

• Use only the power adapter supplied to power the USB3.0 hub.

• Do not pull the power plug from the mains socket by pulling on the cable.

•

If the power adapter or power cable is damaged, do not touch it; electric

shock carries a risk of danger to life!

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microﬁlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent

the technical status at the time of printing.

Important!

According to the USB3.0 standard, a USB3.0 ports supplies a current of

900 mA (e.g. the USB3.0 port of your computer).

However, many USB3.0 devices only require a much lower current, e.g. USB

sticks. Other USB3.0 devices are powered by their own power adapter (e.g.

large USB3.0 hard drives).

The two USB power outputs can supply an output current of max. 2.4 A each.

Remember that the power adapter provided cannot supply all outputs with

the maximally possible current at the same time. The output power of the

power adapter provided is 48 W, of which about 47.5 W are available for all

connected USB devices (USB ports 1 - 7 and both USB power outputs).

Charge function

The two USB power outputs at the top of the USB3.0 hub supply a current of up to

2.4 A. Hence, not only smartphones can be connected here (they usually require a

charging current between 0.5 and 1 A) but also tablets with a higher current require-

ment (e.g. iPad).

Use the USB charging cable provided with your smartphone or tablet to connect it to

a USB power output.

Since the charging electronics are integrated in the smartphone or tablet, the charg-

ing process is controlled and completed by the smartphone or tablet.

The LED of the respective USB power output next to the USB socket is lit when a USB

device is connected and uses current.

The two USB power outputs are only active when the USB3.0 hub is switched

on.

Tips and notes

• The USB2.0 hub is USB2.0 and USB1.1 compatible. This means that normal USB2.0

and USB1.1 devices can be used without any problem on the USB3.0 hub. However,

this will not speed up the USB2.0/USB1.1 devices.

• In order to take advantage of the high speed provided by USB3.0, all the devices

must support USB3.0: The USB device itself (e.g. an external hard disk), the USB hub

and the USB controller in the computer.

• The theoretical maximum speed for USB3.0 (or also USB2.0 or USB1.1) is never

achieved in practice. This is due to protocol information, simultaneous operation of

several USB devices or the speed limit of the connected device or the USB control-

lers/motherboards.

It also makes little sense to simultaneously operate 7 hard drives via the USB3.0 hub,

as these share the possible volume of data transmission between the USB3.0 hub

and computer.

If, for example, a lot of data is to be transferred between two USB3.0 hard drives,

connect the ﬁrst hard drive to the USB3.0 port on the USB3.0 hub and connect the

second directly to a USB3.0 port on the computer.

• Normally USB operation is not possible in DOS or in the protected mode of older

Windows versions. Depending on the computer or the BIOS/Setup, however, opera-

tion of a USB keyboard and a USB mouse is possible. Nevertheless, it is necessary

to connect them directly to the computer’s USB interface and not to the USB hub.

• USB devices can be connected and disconnected during operation. You do not have

to switch off your computer if you want to insert or remove devices.

If data transfers are in progress on the USB port, e.g., if an external disk is inputting

data into the computer, and you unplug the USB plug, the operating system might

crash. Furthermore, loss of data or damage to the ﬁle system of the external drive

can be the result.

The same applies when you press the switch on/off button of the USB3.0 hub.

• With Windows

XP, Vista™, 7, 8, an icon with an arrow in the menu bar is displayed

for some USB devices (e.g. for a USB hard disk). With this function you can “discon-

nect” the USB device from the computer so that no data transfer occurs any longer.

Afterwards, the USB device can be disconnected from the USB3.0 hub (or the com-

puter) without problems.

Maintenance and cleaning

The product is maintenance-free. Repair or maintenance work must be carried out

by a specialist.

You can use a clean, dry, soft cloth for cleaning. Dust can be very easily removed with

a soft, clean brush and a vacuum cleaner.

Do not use aggressive, chemical or scouring cleaning agents, as this may lead to dis-

colouration or changes in the material on the surface.

Disposal

The product must not be disposed of in the household waste.

Dispose of the product at the end of its serviceable life in accordance with

the current statutory requirements; e.g., return it to any suitable collection

point.

Technical information

a) USB hub

Operating voltage................................. 12 V/DC

USB standard........................................ USB3.0 (compatible with USB2.0 and USB1.1)

Number of USB3.0 ports ..................... 7

Number of USB power outputs.......... 2 (output current max. 2.4 A each; output voltage

5 V/DC)

On/Off switch ........................................ yes

Wall mounting ....................................... yes (distance between screws 114 mm)

Ambient conditions .............................. Temperature 0 °C to +40 °C, air humidity 10% to

90% relative, not condensing

Dimensions (W x H x D)....................... 202 x 61 x 26 mm

Weight .................................................... 142 g

b) Power adapter

Operating voltage................................. 100 - 240 V/AC, 50/60 Hz

Output..................................................... 12 V/DC, 4 A

Page is loading ...

Renkforce 7+2 ports USB 3.0 hub + quick-charge port, + LED indicator lights Owner's manual

Brand: Renkforce

Model: 7+2 ports USB 3.0 hub + quick-charge port, + LED indicator lights

Category: Coffee making accessories

Type: Owner's manual

Download PDF

report

Renkforce 7+2 ports USB 3.0 hub + quick-charge port, + LED indicator lights Owner's manual

Renkforce 7+2 ports USB 3.0 hub + quick-charge port, + LED indicator lights Owner's manual

in other languages

Related papers

Other documents