Installation & operation of
your Freezer/Refrigerator
It is important that your appliance is installed and
operated in accordance with the manufacturer’s
instructions to guarantee the performance,
efficiency and operation.
• Positiontheapplianceinasafe&securelocation.
Limit exposure to heat sources or direct sunlight
which can affect the unit’s performance and
efficiency.
• Thenormaloperationoftheappliancerequires
heat to be radiated away from the condensers
located in the front and end of the cabinet.
Adequateairowisrequiredtobeavailable
around the compressor at all times.
• Thecoolingsystemhasbeendesignedto
operate correctly when the appliance is
positioned on angles up to 35 degrees. It is
recommended that the time the unit is exposed
toanglesover30degreesislimitedtoa
maximum of four (4) hours continuous operation.
• Yourappliancecanbeusedaseitherafreezer
or a refrigerator, it cannot be used as both
simultaneously.
Important
• Thisapplianceisnotintendedforuseby
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
ofexperienceandknowledge,unlesstheyhave
beengivensupervisionorinstructionconcerning
use of the appliance by a person responsible for
their safety.
• Childrenshouldbesupervisedtoensurethat
they do not play with the appliance.
• Thisapplianceissuitableforcampinguse
• Theapplianceshallnotbeexposedtorain
Power Requirements
TheFreezer/Refrigeratorisdesignedtooperateon
AC&DCvoltageinputs.
AC Input – Voltage is required to be
220-240V AC at 50Hz
DC Input – Voltage is required to be
12-24V DC +/-10%
ThepowersystemisttedwithanAutomaticVoltage
changeoverprogram;thiswillallowforboththeAC&
DC power cords to be connected to the appliance at
thesametime.TheACpowerinputhaspriorityand
theunitwillselectthisinputoverDCifbotharebeing
provided.
Once the AC power is shut off the appliance will then
switchovertoDCpower.Thecompressorwillnot
start immediately as the controller will program itself
for the change in supply and within 3 minutes the unit
willrestartusingtheDCinput.Thissameprocesswill
be taken if AC power is resupplied to the appliance.
Defrosting the cabinet
If your appliance is being used solely as a
freezer,itispossiblethatabuildupoficeon
theinteriormayoccur.Thisbuildupcanaffectthe
performance&efciencyofthecoolingsystemand
mustberemoved.
Donotusesolidorsharputensilssuchasknivesto
removetheiceasthismayresultindamagetotheunit.
Turntheapplianceoffandremovethecontentfrom
the cabinet, allow the ice to melt, then drain the water
from the cabinet. Use a soft clean cloth
to wipe down all surfaces and allow to dry.
Operation of the controller
ThetemperaturecontrollerttedtoyourFreezer/
Refrigeratorprovidestheabilitytosetthedesired
temperaturelevel.Thedigitalreadoutwillprovide
informationonthecabinet&settemperature.
Theelectroniccontrollerhasbeenprogrammed
tomaintainanaverageofthesettemperature.
Thecompressorwillstartupwhentheinternal
cabinettemperatureincreasesabovetheselected
and will run until the temperature is 2 to 3 degrees
below the set before shutting off.
Setting the temperature
WhenyourFreezer/Refrigeratorisrstconnected
to AC or DC input, the LED light will identify the
selectedvoltage,thereadoutwillashforve(5)
seconds showing the factory setting of -20 degrees,
it will then return to the current cabinet temperature.
TosetthetemperaturepushtheUp/Downbuttons
until the desired cabinet temperature is reached, the
readoutwillashforve(5)secondsthenreturnto
the current cabinet temperature.