Lakeshore 7400 Series VSM Installation guide

Brand
Lakeshore
Model
7400 Series VSM
Type
Installation guide
Installation Instructions – Model 740946
Sample Tail Guide Kit for 7410 VSM
Lake Shore Cryotronics, 575 McCorkle Blvd. Westerville, OH 43082 www.lakeshore.com
Phone (614) 891-2243 – Fax (614) 891-1362 – sales@lakeshore.com – s[email protected]
Introduction
When the user tries to measure hard magnetic materials with a large signal, especially under high field, the
sample can be attracted towards the magnet pole thus make the VSM measurement impossible. This sample tail
guide can be added to the 7410 VSM head to keep sample from moving towards magnet pole.
The instructions below assume the VSM system has the standard setup and is in good working order.
Sample tail guide assembly
1. Assemble the sample guide assembly. All the tips of the Nylon thumb screws should be flush with the
inner surface of the lock ring.
2. Remove the fiberglass sample tube from its packing tube. Install the sample tail guide (661-162) onto
the rod adapter.
Sample tail
Sample tail Guide
Sample Guide Tube
Nylon Thumb Screws
Lock Ring
Form F176-15-00_B Page 2 of 3 5 March 2015
3. Check fit of the sample tail guide against the ID of the brass Sample guide tube. It should slide freely
against the ID the tube, but snug. There should no play when moving the sample tail from side to side.
The triangle guide was intentionally made slightly oversized. Use 300 – 400 grid sand paper to reduce
the points of the guide to fit the tube ID.
4. Replace the thumb screws in the lower VSM head with nylon tipped stainless steel set screws. Replace
them one at a time. Stop when the screw tip hits the surface. Do not apply a force great enough to
change the driving rod position in the head.
5. Attach the sample tail guide assembly you made in step 1 to the stainless steel set screws. You should
feel no binding during the installation.
6. Visually center the ring and tight the horizontal positioning thumb screws.
Stainless Screws
(lock ring support)
Sample guide tube
Thumb Screw
(Vertical adjustment)
Thumb Screw
(Horizontal adjustment)
Lock ring
Form F176-15-00_B Page 3 of 3 5 March 2015
7. Put a level on the guide tube and use the vertical adjustment screws to position the tube in vertical.
8. Slide the head to a forward position such that the guide tube can be unscrewed and dropped off.
9. Attach the sample tail with the guide to the head drive.
10. Slide the guide tube over the sample guide and rod. Take care that you do not bend the sample tail.
Again attach the guide tube to the lock ring.
11. Screw the special sample holder to the sample tail adaptor. Now the installation is complete.
12. The VSM system can be run as normal.
Helpful notes:
1. It is preferred to remove the sample holder only during sample exchange.
2. One should identify the lock ring orientation with respect to the bottom of the VSM head when
removing the guide tube assembly for ease of re-installation. Always loosen the 4 horizontal position
screw before twisting off the lock ring.
3. The user will likely have a custom made sample holder for large sample. It is important to note that the
sample holder diameter must be less than 0.75” (19mm). Also, the sample holder needs a #8-32 x 0.4”
deep internal thread to attach to the sample tail.
4. If needed, the standard sample holder (730931) top can be added to lengthen the sample holder 0.56“
(14.3mm).
Sample tail Guide
Customer supplied
sample holder
Sample guide tube
(Lowered)
Sample guide tube
Customer supplied
sample holder
  • Page 1 1
  • Page 2 2
  • Page 3 3

Lakeshore 7400 Series VSM Installation guide

Brand
Lakeshore
Model
7400 Series VSM
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents