Bosch DDW88MM66/02 User manual and assembly instructions
- Category
- Cooker hoods
- Type
- User manual and assembly instructions
This manual is also suitable for
en Safety
2
Further information and explanations are available online:
Table of contents
INFORMATION FOR USE
1 Safety ...................................................................2
2 Avoiding material damage..................................5
3 Environmental protection and saving en-
ergy ......................................................................5
4 Operating modes ................................................5
5 Familiarising yourself with your appliance .......7
6 Before using for the first time ............................8
7 Basic operation ...................................................8
8 HomeConnect ..................................................10
9 Hob-based hood control...................................11
10 Cleaning and servicing.....................................11
11 Troubleshooting................................................14
12 Disposal.............................................................15
13 Customer Service..............................................15
14 Accessories.......................................................15
15 Declaration of Conformity ................................16
16 Test information................................................16
17 INSTALLATION INSTRUCTIONS ......................16
17.3 Secure installation ............................................17
1 Safety
Observe the following safety instructions.
1.1 General information
¡Read this instruction manual carefully.
¡Keep the instruction manual and the
product information safe for future refer-
ence or for the next owner.
¡Do not connect the appliance if it has been
damaged in transit.
1.2 Intended use
This appliance is designed only to be built
into kitchen units. Read the special installation
instructions.
The appliance can only be used safely if it is
correctly installed according to the safety in-
structions. The installer is responsible for en-
suring that the appliance works perfectly at its
installation location.
Only use this appliance:
¡For extracting cooking vapour.
¡in private households and in enclosed
spaces in a domestic environment.
¡up to an altitude of max. 4000m above
sea level.
Do not use the appliance:
¡in combination with a gas hob.
¡With an external timer.
1.3 Restriction on user group
This appliance may be used by children aged
8 or over and by people who have reduced
physical, sensory or mental abilities or inad-
equate experience and/or knowledge,
provided that they are supervised or have
been instructed on how to use the appliance
safely and have understood the resulting
dangers.
Do not let children play with the appliance.
Children must not perform cleaning or user
maintenance unless they are at least 15 years
old and are being supervised.
Keep children under the age of 8 years away
from the appliance and power cable.
1.4 Safe use
WARNING‒Risk of fire!
Unsuitable appliance combinations may
cause damage.
▶Do not use the appliance in combination
with gas hobs.
Safety en
3
WARNING‒Risk of suffocation!
Children may put packaging material over
their heads or wrap themselves up in it and
suffocate.
▶Keep packaging material away from chil-
dren.
▶Do not let children play with packaging ma-
terial.
Children may breathe in or swallow small
parts, causing them to suffocate.
▶Keep small parts away from children.
▶Do not let children play with small parts.
WARNING‒Risk of poisoning!
Risk of poisoning from flue gases being
drawn back in. Room-air-dependent heat-pro-
ducing appliances (e.g. gas, oil, wood or coal-
operated heaters, continuous flow heaters or
water heaters) obtain combustion air from the
room in which they are installed and dis-
charge the exhaust gases into the open
through an exhaust gas system (e.g. a chim-
ney). With the extractor hood switched on, air
is extracted from the kitchen and the adjacent
rooms. Without an adequate supply of air, the
air pressure falls below atmospheric pressure.
Toxic gases from the chimney or the extrac-
tion shaft are sucked back into the living
space.
▶Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as a
room-air-dependent heat-producing appli-
ance is being operated.
▶It is only possible to safely operate the ap-
pliance if the pressure in the room in which
the heating appliance is installed does not
fall below 4Pa(0.04mbar). This can be
achieved whenever the air needed for com-
bustion is able to enter through openings
that cannot be sealed, for example in
doors, windows, incoming/exhaust air wall
boxes or by other technical means. An in-
coming/exhaust air wall box alone is not
sufficient to ensure compliance with the
limit.
▶In any case, consult your responsible chim-
ney sweep. They are able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures
to you.
WARNING‒Risk of fire!
Fatty deposits in the grease filters may catch
fire.
▶Never operate the appliance without a
grease filter.
▶Clean the grease filters regularly.
en Safety
4
▶Never work with naked flames close to the
appliance (e.g. flambéing).
▶Do not install the appliance near a solid
fuel heating appliance (e.g. wood- or coal-
burning) unless the heating appliance has
a sealed, non-removable cover. There must
be no flying sparks.
Hot oil or grease ignites very quickly.
▶Always supervise hot oil and fat.
▶Never extinguish burning oil or fat with wa-
ter. Switch off the cooking zone. Extinguish
flames carefully using a lid, fire blanket or
something similar.
WARNING‒Risk of burns!
The accessible parts of the appliance become
hot during operation.
▶Never touch these hot parts.
▶Keep children at a safe distance.
The appliance becomes hot during operation.
▶Allow the appliance to cool down before
cleaning.
WARNING‒Risk of injury!
Components inside the appliance may have
sharp edges.
▶Carefully clean the appliance interior.
Items placed on the appliance may fall off.
▶Do not place any objects on the appliance.
Changes to the electrical or mechanical as-
sembly are dangerous and may lead to mal-
functions.
▶Do not make any changes to the electrical
or mechanical assembly.
The light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1).
▶Do not look directly into the switched-on
LED lights for longer than 100seconds.
If the appliance is operated by another person
via the HomeConnect app during cleaning,
this increases the risk of injury.
▶Before cleaning, disconnect the appliance
from the HomeConnect app.
→"Resetting the connection", Page10
WARNING‒Risk of electric shock!
If the appliance or the power cord is dam-
aged, this is dangerous.
▶Never operate a damaged appliance.
▶Never pull on the power cord to unplug the
appliance. Always unplug the appliance at
the mains.
▶If the appliance or the power cord is dam-
aged, immediately unplug the power cord
or switch off the fuse in the fuse box.
▶Call customer services. →Page15
Improper repairs are dangerous.
▶Repairs to the appliance should only be
carried out by trained specialist staff.
▶Only use genuine spare parts when repair-
ing the appliance.
▶If the power cord of this appliance is dam-
aged, it must be replaced by trained spe-
cialist staff.
An ingress of moisture can cause an electric
shock.
▶Before cleaning, pull out the mains plug or
switch off the fuse in the fuse box.
▶Do not use steam- or high-pressure clean-
ers to clean the appliance.
Penetrating liquid may cause an electric
shock.
▶If a larger amount of liquid is flowing in the
appliance, pull out the mains plug or switch
off the fuse in the fuse box.
→"Malfunctions", Page14
WARNING‒Risk of explosion!
Highly caustic alkaline or highly acidic clean-
ing agents in conjunction with aluminium parts
in the interior of the appliance may cause ex-
plosions.
▶Never use highly caustic alkaline or highly
acidic cleaning agents. In particular, do not
use commercial or industrial cleaning
agents in conjunction with aluminium parts,
e.g. grease filter on extractor hoods.
WARNING‒Risk of fire!
Fatty deposits in the grease filters may catch
fire.
▶Clean the grease filters regularly.
WARNING‒Risk of injury!
Improper repairs are dangerous.
▶Repairs to the appliance should only be
carried out by trained specialist staff.
▶If the appliance is defective, call Customer
Service.
→"Customer Service", Page15
WARNING‒Risk of electric shock!
Penetrating moisture may cause an electric
shock.
▶Do not use wet sponge cloths.
Avoiding material damage en
5
2 Avoiding material damage
ATTENTION!
Condensate may cause corrosion damage.
▶To prevent condensation from building up, switch on
the appliance during cooking.
If moisture gets into the controls, this may result in
damage.
▶Never clean controls with a wet cloth.
Incorrect cleaning damages the surfaces.
▶Follow the cleaning instructions.
▶Do not use harsh or abrasive detergents.
▶Clean stainless steel surfaces in the direction of the
finish only.
▶Never clean controls with stainless steel cleaners.
Condensation that flows back in may damage the ap-
pliance.
▶The air extraction duct must be installed with a
gradient of at least 1° from the appliance.
If you put incorrect stress on the design elements, they
may break off.
▶Do not pull design elements.
▶Do not place objects on the design elements or
hang objects from them.
There is a risk of surface damage if you do not peel off
the protective film.
▶Remove the protective film from all parts of the ap-
pliance before using for the first time.
Objects set down on the appliance may damage the
appliance when it is extended.
▶Do not place any objects on the appliance.
▶With the remote control via the HomeConnect app
in particular, ensure that there are no objects on the
appliance.
Painted surfaces are easily damaged.
▶Follow the cleaning instructions.
→"Cleaning the appliance", Page11
▶Ensure that the painted surfaces are not scratched.
3 Environmental protection and saving energy
3.1 Disposing of packaging
The packaging materials are environmentally compat-
ible and can be recycled.
▶Sort the individual components by type and dispose
of them separately.
3.2 Saving energy
If you follow these instructions, your appliance will use
less power.
Adjust the fan speed to the amount of steam pro-
duced during cooking.
¡The lower the fan speed, the less energy is con-
sumed.
Only use the intensive mode as required.
If cooking produces large amounts of steam, select a
higher fan speed in good time.
¡The odours are distributed around the room less.
Switch off the lighting if it is no longer required.
¡When the lighting is switched off, it does not con-
sume any energy.
Clean or replace the filters at regular intervals.
¡The effectiveness of the filter is retained.
Put the cooking lid on.
¡The cooking vapours and condensation are re-
duced.
Only use the additional functions if required.
¡Switching off additional functions reduces power
consumption.
4 Operating modes
You can use your appliance in air extraction mode or
circulating-air mode.
The saturation indicator must be adjusted to the selec-
ted operating mode and the filters used.
→"Setting the saturation indicator", Page9
4.1 Air extraction mode
The air which is drawn in is cleaned by the grease fil-
ters and conveyed to the exterior by a pipe system.
The air must not be discharged into a
flue that is used for exhausting fumes
from appliances burning gas or other
fuels (not applicable to appliances that
only discharge the air back into the
room).
¡If the exhaust air is to be conveyed
into a non-functioning smoke or ex-
haust gas flue, you must obtain the
consent of the heating engineer re-
sponsible.
¡If the exhaust air is conveyed
through the external wall, a tele-
scopic duct should be used.
en Operating modes
6
4.2 Air recirculation
The air which is drawn in is cleaned by the grease fil-
ters and an odour filter, and conveyed back into the
room.
To bind odours in air recirculation
mode, you must install an odour filter.
The different options for operating the
appliance in air circulation mode can
be found in our catalogue. Alternatively,
ask your dealer. The required accessor-
ies are available from specialist retail-
ers, from our after-sales service or from
the online shop.
→"Accessories", Page15
Familiarising yourself with your appliance en
7
5 Familiarising yourself with your appliance
5.1 Overall view
You can find an overview of the parts of your appliance
here.
1
2
3
4
7 6
5
1
Glass plate
2
Grease filter
3
Filter cartridge
4
Appliance
5
Blower group
6
Cover plate
7
Drip tray
5.2 Controls
You can use the controls to configure all functions of
your appliance and to obtain information about the op-
erating status.
5
3
4
1
2
7
6
1
Fan setting 1
2
Fan setting 2
3
Fan setting 3
4
Intensive mode 1
5
Intensive mode 2
6
Odour filter saturation indicator1
7
Grease filter saturation indicator
1Depending on the appliance specifications
Switching the appliance on or off
Increasing the fan setting
Decreasing the fan setting
Switching automatic mode1 on or off
HomeConnect Establishing a connection
Reset the filter saturation indicator
Removing or inserting the grease filter/odour
filter1
Switching Guided Air on or off
1Depending on the appliance specifications
en Before using for the first time
8
6 Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
6.1 Setting an operating mode
Your appliance is set to air extraction mode by default.
Note:When using it in circulating-air mode, you require
additional accessories.
▶When using it in circulating-air mode, set the operat-
ing mode.
→"Setting the saturation indicator", Page9
6.2 Optimal use of the appliance
The Guided Air function improves the extraction of the
cooking vapour. In order to optimally use your appli-
ance, switch this function on before using the appli-
ance for the first time.
▶Switch on Guided Air. →Page9
7 Basic operation
7.1 Switching on the appliance
▶Press to switch on the appliance.
aThe appliance starts at fan setting2.
aThe Ambient Light1 automatically switches on.
7.2 Switching off the appliance
▶Press .
aThe fan run-on starts at fan setting1.
aThe Ambient Light1 remains switched on for ap-
prox.10minutes.
aThe glass panel remains extended halfway.
aThe appliance switches off automatically after ap-
prox. 10 minutes.
aIf you have installed the appliance and have estab-
lished the power connection, the glass pane moves
downwards and appliance closes.
7.3 Selecting a fan setting
▶Press or .
7.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
1. Press repeatedly until LED4 lights up in the LED
display for intensive mode1.
2. Press repeatedly until LED5 lights up in the LED
display for intensive mode2.
aAfter approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.5 Switching off intensive mode
▶To select a fan setting of your choice, press .
7.6 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
Note:Further settings are available in the HomeCon-
nectapp.
Requirement:The appliance is switched on.
▶Press .
aThe fan run-on starts at fan setting1.
aThe Ambient Light1 remains switched on for ap-
prox.10minutes.
aThe glass panel remains extended halfway.
aThe appliance switches off automatically after ap-
prox. 10 minutes.
aIf you have installed the appliance and have estab-
lished the power connection, the glass pane moves
downwards and appliance closes.
7.7 Intermittent ventilation
In order to regularly ventilate your kitchen, you can use
the interval ventilation. With interval ventilation, the vent-
ilation system switches on and off in the selected set-
ting for the selected time.
Note:This function is only available in the HomeCon-
nectapp.
If the interval ventilation is switched on, LED1 flashes.
7.8 Switching on automatic mode1
The optimum fan setting is set automatically using a
sensor.
▶Press .
aThe LED for the automatically set fan setting lights
up in the LED display.
Note:In automatic mode, the Guided Air function is al-
ways switched on.
7.9 Switching off automatic mode1
▶Press .
aThe appliance starts at fan setting2.
aThe ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
aAutomatic mode runs for a maximum of four hours.
Note:Further settings are available in the HomeCon-
nectapp.
1Depending on the appliance specifications
Basic operation en
9
7.10 Sensor sensitivity1
In automatic mode, a sensor in the appliance detects
the intensity of the cooking odours and roasting
odours. Depending on the setting of the sensor sensit-
ivity, the optimum fan setting is automatically switched
on.
If the sensor control reacts too weakly or too strongly,
you can change the setting for the sensor sensitivity.
¡Default setting: Fan setting3
¡Lowest setting: Fan setting1
¡Highest setting: Fan setting5
7.11 Setting the sensor sensitivity1
Requirement:The appliance is switched on.
1. Press and hold and for approx.3seconds.
2. Press or to change the setting.
3. Press to save the setting.
Or wait approx. fiveseconds until the setting is
saved automatically.
aA signal tone sounds as soon as the selected set-
ting is saved.
7.12 Saturation indicator
If the grease filters or odour filters are saturated, cor-
responding symbols flash after the appliance is
switched off.
Note:You can set the saturation indicator in the Home
Connect app depending on the filter used.
Clean the saturated grease filters and, in doing so, ob-
serve the cleaning instructions in these instructions.
Change the saturated odour filters and observe the in-
structions in the accompanying instructions.
If odour filters can be regenerated, follow the instruc-
tions in the accompanying instructions.
7.13 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement:The appliance is switched on.
1. Press and hold and for approx. 3 seconds.
‒To set circulating-air mode (Clean Air Standard
circulating-air set or Clean Air Plus circulating-air
set), press and hold / until LED2 lights up in
the LED display.
‒To set circulating-air mode (regenerable filter),
press / until LED3 lights up in the LED dis-
play.
‒To convert the electronic control back to opera-
tion without the air recirculation filter, press /
until LED1 lights up on the LED display.
2. Press to save the setting.
Or wait approx. fiveseconds until the setting is
saved automatically.
aA signal tone sounds as soon as the selected set-
ting is saved.
7.14 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡After switching off the appliance, the upper two LEDs
for the grease filter's saturation indicator and/or the
lower two LEDs for the odour filter's saturation indic-
ator flash in the left hand control panel.
¡A signal sounds repeatedly.
▶Press .
aThe saturation indicator is reset.
7.15 Switching on Ambient Light1
Notes
¡You can switch the Ambient Light on and off in the
HomeConnect app.
¡Additional colours are available in the HomeCon-
nectapp.
Requirement:Fan setting1 is switched on.
▶Press .
aThe Ambient Light remains switched on.
aThe ventilation system switches off.
aThe glass panel remains at the top.
7.16 Switching on Guided Air
With the Guided Air function, the cooking vapour is
routed in such a way that it can be optimally collected
from the appliance and removed. The extraction of the
cooking vapour is improved on front cooking zones in
particular.
Note:This function is switched off by default.
▶Press .
7.17 Switching off Guided Air
▶Press .
1Depending on the appliance specifications
en HomeConnect
10
8 HomeConnect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the HomeConnect app, adjust its basic settings
and monitor its operating status.
The HomeConnect services are not available in every
country. The availability of the HomeConnect function
depends on the availability of HomeConnect services
in your country. You can find information about this at:
www.home-connect.com.
The HomeConnect app guides you through the entire
login process. Follow the instructions in the HomeCon-
nect app to configure the settings.
Tips
¡Please consult the documents supplied by
HomeConnect.
¡Please also follow the instructions in the HomeCon-
nect app.
Notes
¡Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the HomeCon-
nect app.
→"Safety", Page2
¡Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the HomeConnect
app.
¡In networked standby mode, the appliance requires
a maximum of2W.
¡If you need your device's MAC address to connect
to your home network, you can find this next to the
rating plate. →Page15
8.1 Setting up HomeConnect
Requirements
¡The appliance is connected to the power supply and
is switched on.
¡You have a mobile device with a current version of
the iOS or Android operating system, e.g. a smart-
phone.
¡The mobile device and the appliance are within
range of your home network's WiFi signal.
1. Download the HomeConnect app.
1
1Apple App Store und the Apple App Store logo are
trademarks of Apple Inc. Google Play and the
Google Play logo are trademarks of Google LLC.
2. Open the HomeConnect app and scan the follow-
ing QR code.
3. Follow the instructions in the HomeConnect app.
8.2 Resetting the connection
▶Reset the saved connections to the Wi-Fi and
HomeConnect by pressing and holding and
for approx. threeseconds.
8.3 Software update
Your appliance's software can be updated using the
software update function, e.g. for the purposes of op-
timisation, troubleshooting or security updates.
To do this, you must be a registered HomeCon-
nectuser, have installed the app on your mobile device
and be connected to the HomeConnectserver.
As soon as a software update is available, you will be
informed via the HomeConnectapp and will be able to
start the software update via the app. Once the update
has been successfully downloaded, you can start in-
stalling it via the HomeConnectapp if you are in your
home network (Wi-Fi). The HomeConnectapp informs
you once installation is successful.
Notes
¡The software update consists of two steps.
–The first step is the download.
–The second step is the installation on your appli-
ance.
¡You can continue to use your appliance as normal
while updates are downloading. Depending on your
personal settings in the app, software updates can
also be set to download automatically.
¡Installation takes a few minutes. You cannot use
your appliance during installation.
¡We recommend that you install security updates as
soon as possible.
8.4 Remote diagnostics
Customer Service can use Remote Diagnostics to ac-
cess your appliance if you contact them, have your ap-
pliance connected to the HomeConnect server and if
Remote Diagnostics is available in the country in which
you are using the appliance.
Tip:For further information and details about the avail-
ability of Remote Diagnostics in your country, please
visit the service/support section of your local website:
www.home-connect.com.
Hob-based hood control en
11
8.5 Data protection
Please see the information on data protection.
The first time your appliance is registered on a home
network connected to the Internet, your appliance will
transmit the following types of data to the
HomeConnect server (initial registration):
¡Unique appliance identification (consisting of appli-
ance codes as well as the MAC address of the Wi-Fi
communication module installed).
¡Security certificate of the Wi-Fi communication mod-
ule (to ensure a secure data connection).
¡The current software and hardware version of your
appliance.
¡Status of any previous reset to factory settings.
This initial registration prepares the HomeConnect
functions for use and is only required when you want to
use the HomeConnect functions for the first time.
Note:Please note that the HomeConnect functions
can only be utilised with the HomeConnect app. In-
formation on data protection can be retrieved in the
HomeConnect app.
9 Hob-based hood control
You can connect your appliance to a suitable hob and,
in this way, control the functions of your appliance via
the hob.
If the hob and the extractor hood are HomeConnect-
compatible, connect the appliances in the HomeCon-
nectapp. To do this, connect the two appliances to
HomeConnect and follow the instructions in the app.
Notes
¡Please note the safety precautions in the instruction
manual for your appliance and ensure that they are
also observed when operating the appliance via the
hob-based hood control.
¡Operating your appliance always takes priority. It is
not possible to use the hob-based hood control dur-
ing this time.
¡You can only connect to the extractor hood via the
HomeConnect app. Other connection routes are no
longer supported.
10 Cleaning and servicing
To keep your appliance working efficiently for a long
time, it is important to clean and maintain it carefully.
10.1 Cleaning products
You can obtain suitable cleaning products from after-
sales service or the online shop.
ATTENTION!
Unsuitable cleaning products may damage the sur-
faces of the appliance.
▶Do not use harsh or abrasive detergents.
▶Do not use cleaning products with a high alcohol
content.
▶Do not use hard scouring pads or cleaning
sponges.
▶Only use glass cleaners, glass scrapers or stainless
steel care products if recommended in the cleaning
instructions for the relevant part.
▶Wash sponge cloths thoroughly before use.
10.2 Cleaning the appliance
Clean the appliance as specified. This will ensure that
the different parts and surfaces of the appliance are
not damaged by incorrect cleaning or unsuitable clean-
ing products.
WARNING‒Risk of explosion!
Highly caustic alkaline or highly acidic cleaning agents
in conjunction with aluminium parts in the interior of the
appliance may cause explosions.
▶Never use highly caustic alkaline or highly acidic
cleaning agents. In particular, do not use commer-
cial or industrial cleaning agents in conjunction with
aluminium parts, e.g. grease filter on extractor
hoods.
WARNING‒Risk of electric shock!
An ingress of moisture can cause an electric shock.
▶Before cleaning, pull out the mains plug or switch
off the fuse in the fuse box.
▶Do not use steam- or high-pressure cleaners to
clean the appliance.
WARNING‒Risk of burns!
The appliance becomes hot during operation.
▶Allow the appliance to cool down before cleaning.
WARNING‒Risk of injury!
Components inside the appliance may have sharp
edges.
▶Carefully clean the appliance interior.
en Cleaning and servicing
12
If the appliance is operated by another person via the
HomeConnect app during cleaning, this increases the
risk of injury.
▶Before cleaning, disconnect the appliance from the
HomeConnect app.
→"Resetting the connection", Page10
1. Observe the information regarding the cleaning
agents.
2. Clean as follows, depending on the surface:
‒Clean stainless steel surfaces in the direction of
the finish using a sponge cloth and hot soapy
water.
‒Clean painted surfaces using a damp sponge
cloth and hot soapy water.
‒Clean aluminium using a soft cloth and glass
cleaner.
‒Clean plastic using a soft cloth and glass
cleaner.
‒Clean glass using a soft cloth and glass cleaner.
3. Dry with a soft cloth.
4. Apply a thin layer of the stainless steel cleaning
product to stainless steel surfaces using a soft
cloth.
You can obtain stainless steel cleaning products
from the after-sales service or the online shop.
10.3 Cleaning controls and lights
WARNING‒Risk of electric shock!
Penetrating moisture may cause an electric shock.
▶Do not use wet sponge cloths.
1. Observe the information regarding the cleaning
agents.
2. Clean using a damp sponge cloth and hot soapy
water.
3. Dry with a soft cloth.
10.4 Cleaning the glass panel
1. Note:The appliance frame is sensitive. Remove the
glass pane vertically. Do not pull the glass pane
over the appliance frame.
The glass pane is heavy.
Carefully remove the glass pane.
2. Observe the information regarding the cleaning
agents.
3. Clean with a soft cloth and glass cleaner.
4. Carefully insert the glass pane as far as it will go
into the guides.
10.5 Cleaning the drip tray
When cooking or cleaning the appliance, liquid may
get into the appliance. The drip trays are used to col-
lect this liquid.
1. Remove the drip tray and empty it .
2. Observe the information regarding the cleaning
agents.
3. Clean the drip tray and re-insert it.
10.6 Removing the grease filter
1. Press .
aThe glass panel moves halfway down and the
grease filter cartridges are transported to the top.
Cleaning and servicing en
13
2. Remove the grease filters.
To avoid causing damage, do not bend the grease
filters.
10.7 Cleaning grease filters manually
The grease filters filter the grease from the cooking va-
pour. Regularly cleaned grease filters guarantee a high
level of grease removal. We recommend cleaning the
grease filters every two months.
WARNING‒Risk of fire!
Fatty deposits in the grease filters may catch fire.
▶Clean the grease filters regularly.
Requirement:The grease filters have been removed.
→"Removing the grease filter", Page12
1. Observe the information regarding the cleaning
agents.
2. Soak the grease filter in hot soapy water.
Use special grease solvent for stubborn dirt. You
can obtain grease solvents from customer service
or the online shop.
3. Use a brush to clean the grease filters.
4. Rinse the grease filters thoroughly.
5. Allow the grease filters to drain.
10.8 Cleaning grease filters in the
dishwasher
The grease filters filter the grease from the cooking va-
pour. Regularly cleaned grease filters guarantee a high
level of grease removal. We recommend cleaning the
grease filters every two months.
WARNING‒Risk of fire!
Fatty deposits in the grease filters may catch fire.
▶Clean the grease filters regularly.
ATTENTION!
The grease filters may become damaged if they are
squeezed in the dishwasher.
▶Do not squeeze the grease filters.
Note:When cleaning the grease filter in the dish-
washer, light discolouration may occur. This discoloura-
tion has no effect on the performance of the metal
grease filters.
Requirement:The grease filters have been removed.
→"Removing the grease filter", Page12
1. Observe the information regarding the cleaning
agents.
2. Place the grease filters loosely into the dishwasher.
Do not clean heavily soiled grease filters with
utensils.
Use special grease solvent for stubborn dirt. You
can obtain grease solvents from customer service
or the online shop.
3. Start the dishwasher.
Select a temperature of no more than 70°C.
4. Allow the grease filters to drain.
10.9 Removing the grease filter cartridge
▶Note:The appliance frame is sensitive. Remove the
grease filter cartridges vertically. Do not pull the
grease filter cartridges over the appliance frame.
Remove the grease filter cartridges.
10.10 Cleaning the grease filter cartridge
Requirement:The grease filters have been removed.
→"Removing the grease filter", Page12
1. Clean the grease filter cartridge.
You can clean the grease filter cartridges by hand
or in the dishwasher.
2. Observe the information regarding the cleaning
agents.
10.11 Fitting the grease filters
1. Press .
aThe glass panel moves halfway down and the
grease filter cartridges are transported to the top.
2. Insert the grease filter into the grease filter cart-
ridges.
To avoid causing damage, do not bend the grease
filters.
3. Press .
4.
aThe glass panel and the filter cartridges move
downwards.
aThe appliance flap closes and the appliance
switches off.
en Troubleshooting
14
5. Reset the saturation indicator.
→"Resetting the saturation indicator", Page9
11 Troubleshooting
You can rectify minor faults on your appliance yourself.
Read the troubleshooting information before contacting
after-sales service. This will avoid unnecessary costs.
WARNING‒Risk of injury!
Improper repairs are dangerous.
▶Repairs to the appliance should only be carried out
by trained specialist staff.
▶If the appliance is defective, call Customer Service.
→"Customer Service", Page15
WARNING‒Risk of electric shock!
Incorrect repairs are dangerous.
▶Repairs to the appliance should only be carried out
by trained specialist staff.
▶Only use genuine spare parts when repairing the
appliance.
▶If the power cord of this appliance is damaged, it
must be replaced by trained specialist staff.
11.1 Malfunctions
Fault Cause and troubleshooting
The appliance is not
working.
The mains plug of the power cord is not plugged in.
▶Connect the appliance to the power supply.
The circuit breaker in the fuse box has tripped.
▶Check the circuit breaker in the fuse box.
There has been a power cut.
▶Check whether the lighting in your room or other appliances are working.
The glass panel is not inserted correctly.
▶Insert the glass panel carefully as far as it will go.
Liquid flows into the appliance.
▶Pull out the mains plug or switch off the appliance at the circuit breaker in the fuse box.
▶Empty the drip trays and remove the grease filters cartridges. →Page12
▶Dry all accessible places.
▶Leave the appliance flap open and restart the appliance only after 48hours.
▶Insert the drip tray and the grease filters cartridges.
The glass panel is removed, and the appliance has been operated.
▶Insert the glass panel and disconnect the appliance from the power supply for ap-
prox.oneminute.
The appliance flap
does not close com-
pletely.
An object is jammed in the appliance.
▶Disconnect the appliance from the electricity.
▶Carefully open the flap and remove the object that has become jammed.
▶Close the flap carefully.
▶Connect the appliance to the power supply.
The button illumina-
tion does not work.
The control unit is faulty.
▶Call the after-sales service.
→"Customer Service", Page15
The lighting does not
work1.
Different causes are possible.
▶Call the after-sales service.
→"Customer Service", Page15
▶Defective LED lights may be replaced by the manufacturer, their customer service or a
qualified technician (electrician) only.
The top two LEDs
flash in the left-hand
control panel (7).
The grease filters are saturated.
▶Clean the grease filters.
→"Cleaning grease filters in the dishwasher", Page13
→"Cleaning grease filters manually", Page13
→"Familiarising yourself with your appliance", Page7
1Depending on the appliance specifications
Disposal en
15
Fault Cause and troubleshooting
The bottom two LEDs
flash in the left-hand
control panel (6).
The odour filters are saturated.
▶Change the odour filter.
→"Familiarising yourself with your appliance", Page7
HomeConnect is not
working properly.
Different causes are possible.
▶Go to www.home-connect.com.
The hob-based hood
control is not working
properly.
It may be necessary to change the settings.
▶Read the instruction manual for the hob.
▶Go to www.home-connect.com.
12 Disposal
12.1 Disposing of old appliance
Valuable raw materials can be reused by recycling.
1. Unplug the appliance from the mains.
2. Cut through the power cord.
3. Dispose of the appliance in an environmentally
friendly manner.
Information about current disposal methods are
available from your specialist dealer or local author-
ity.
This appliance is labelled in accord-
ance with European Directive
2012/19/EU concerning used elec-
trical and electronic appliances
(waste electrical and electronic equip-
ment - WEEE).
The guideline determines the frame-
work for the return and recycling of
used appliances as applicable
throughout the EU.
13 Customer Service
Function-relevant genuine spare parts according to the
corresponding Ecodesign Order can be obtained from
Customer Service for a period of at least 10 years from
the date on which your appliance was placed on the
market within the European Economic Area.
Note:Under the terms of the manufacturer's warranty
the use of Customer Service is free of charge.
Detailed information on the warranty period and terms
of warranty in your country is available from our after-
sales service, your retailer or on our website.
If you contact Customer Service, you will require the
product number (E-Nr.) and the production number
(FD) of your appliance.
The contact details for Customer Service can be found
in the enclosed Customer Service directory or on our
website.
13.1 Product number (E-Nr.) and production
number (FD)
You can find the product number (E-Nr.) and the pro-
duction number (FD) on the appliance's rating plate.
The rating plate is located on the fan box.
Make a note of your appliance's details and the Cus-
tomer Service telephone number to find them again
quickly.
14 Accessories
You can buy accessories from the after-sales service,
from specialist retailers or online. Only use original ac-
cessories, as these have been specifically designed for
your appliance.
Accessories vary from one appliance to another. When
purchasing accessories, always quote the exact
product number (E no.) of your appliance. →Page15
You can find out which accessories are available for
your appliance in our catalogue, in the online shop or
from our after-sales service.
www.bosch-home.com
Accessories Order number
Clean Air Plus odour filter
– 80cm, replacement
DSZ1WW1B6
Clean Air Plus recircula-
tion kit – 80 cm
DSZ1WW1I6
Accessories Order number
Long Life recirculation kit
– 80cm
DSZ1WW1J1
Installation kit for remov-
able fans
DSZ1WW1M1
Installation kit for seam-
less installation – 80cm
DSZ8WW1Y2
Flat duct piece – straight,
1000mm
HEZ9VDSM2
Flat duct piece – straight,
500mm
HEZ9VDSM1
90° flat duct elbow – hori-
zontal
HEZ9VDSB1
90° flat duct elbow – ver-
tical
HEZ9VDSB2
en Declaration of Conformity
16
Accessories Order number
90° adapter piece –
round/flat
HEZ9VDSI1
Accessories Order number
Adapter piece – round/
flat
HEZ9VDSI0
Connecting sleeve HEZ9VDSS1
15 Declaration of Conformity
BSH Hausgeräte GmbH hereby declares that the appli-
ance with Home Connect functionality conforms to the
basic requirements and other relevant provisions of Dir-
ective 2014/53/EU.
A detailed RED Declaration of Conformity can be found
online at www.bosch-home.com among the additional
documents on the product page for your appliance.
Hereby, BSH Hausgeräte GmbH declares that the ap-
pliance with HomeConnect functionality is in compli-
ance with relevant statutory requirements.1
A detailed Declaration of Conformity can be found on-
line at www.bosch-home.co.uk among the additional
documents on the product page for your appliance.1
2.4 GHz band (2400–2483.5MHz): Max. 100mW
5-GHz band (5150–5350MHz + 5470–5725MHz):
max. 50mW
BE BG CZ DK DE EE IE EL ES
FR HR IT CY LI LV LT LU HU
MT NL AT PL PT RO SI SK FI
SE NO CH TR IS UK (NI)
5GHz WLAN (Wi-Fi): For indoor use only.
AL BA MD ME MK RS UK UA
5GHz WLAN (Wi-Fi): For indoor use only.
16 Test information
This information has been produced to facilitate the in-
spection of the appliance.
¡Measured in accordance with EN 61591.
¡The appliance is operated in its as-delivered condi-
tion.
¡The fan box must be attached on the front of the ap-
pliance.
¡Ensure that the filters do not move during the meas-
urement (by changing the appliance position to the
installation position).
¡The ambient light is not a working light. The ambient
light in light colour red has been added to the FDE
value as a power consumer.
17 Installation instructions
Observe this information when installing the appliance.
1Only applies to Great Britain
Installation instructions en
17
17.1 Included with the appliance
After unpacking all parts, check for any damage in
transit and completeness of the delivery.
17.2 Appliance dimensions
You will find the dimensions of the appliance here
Observe the dimensions of the unit.
17.3 Secure installation
Follow these safety instructions when in-
stalling the appliance.
WARNING‒Risk of poisoning!
Risk of poisoning from flue gases being
drawn back in. Room-air-dependent heat-pro-
ducing appliances (e.g. gas, oil, wood or coal-
operated heaters, continuous flow heaters or
water heaters) obtain combustion air from the
room in which they are installed and dis-
charge the exhaust gases into the open
through an exhaust gas system (e.g. a chim-
ney). With the extractor hood switched on, air
is extracted from the kitchen and the adjacent
rooms. Without an adequate supply of air, the
air pressure falls below atmospheric pressure.
Toxic gases from the chimney or the extrac-
tion shaft are sucked back into the living
space.
▶Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as a
room-air-dependent heat-producing appli-
ance is being operated.
▶It is only possible to safely operate the ap-
pliance if the pressure in the room in which
the heating appliance is installed does not
fall below 4Pa(0.04mbar). This can be
achieved whenever the air needed for com-
bustion is able to enter through openings
that cannot be sealed, for example in
doors, windows, incoming/exhaust air wall
boxes or by other technical means. An in-
coming/exhaust air wall box alone is not
sufficient to ensure compliance with the
limit.
▶In any case, consult your responsible chim-
ney sweep. They are able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures
to you.
en Installation instructions
18
Risk of poisoning from flue gases being
drawn back in.
▶If an extractor hood with an open-flued heat
production source is installed, the power
supply for the extractor hood must be
provided with a suitable safety switch.
Risk of poisoning from flue gases being
drawn back in.
▶Do not emit the exhaust air into a smoke or
exhaust gas flue that is in operation.
▶Do not emit the exhaust air into a shaft that
is used to ventilate installation rooms for
heat-producing appliances.
▶If the exhaust air is to be conveyed into a
smoke or exhaust gas flue, you must obtain
the consent of the heating engineer re-
sponsible.
WARNING‒Risk of suffocation!
Children may put packaging material over
their heads or wrap themselves up in it and
suffocate.
▶Keep packaging material away from chil-
dren.
▶Do not let children play with packaging ma-
terial.
WARNING‒Risk of fire!
The grease deposits in the grease filter may
catch fire.
▶Never work with naked flames close to the
appliance (e.g. flambéing).
▶Do not install the appliance near a heat-
producing appliance for solid fuel (e.g.
wood or coal) unless a closed, non-remov-
able cover is present. There must be no fly-
ing sparks.
▶The specified safety clearances must be
complied with in order to prevent a build-up
of heat.
WARNING‒Risk of injury!
Components inside the appliance may have
sharp edges.
▶Wear protective gloves.
The appliance is heavy.
▶To move the appliance, twopeople are re-
quired.
▶Use only suitable tools and equipment.
Changes to the electrical or mechanical as-
sembly are dangerous and may lead to mal-
functions.
▶Do not make any changes to the electrical
or mechanical assembly.
WARNING‒Risk of fire!
Unsuitable appliance combinations may
cause damage.
▶Do not use the appliance in combination
with gas hobs.
WARNING‒Risk of electric shock!
Sharp-edged components inside the appli-
ance may damage the connecting cable.
▶Do not kink or trap the connecting cable.
If the appliance or the power cord is dam-
aged, this is dangerous.
▶Never operate a damaged appliance.
▶Never pull on the power cord to unplug the
appliance. Always unplug the appliance at
the mains.
▶If the appliance or the power cord is dam-
aged, immediately unplug the power cord
or switch off the fuse in the fuse box.
▶Call customer services. →Page15
Improper repairs are dangerous.
▶Repairs to the appliance should only be
carried out by trained specialist staff.
▶Only use genuine spare parts when repair-
ing the appliance.
▶If the power cord of this appliance is dam-
aged, it must be replaced by trained spe-
cialist staff.
Incorrect installation is dangerous.
▶Connect and operate the appliance only in
accordance with the specifications on the
rating plate.
▶Connect the appliance to a power supply
with alternating current only via a properly
installed socket with earthing.
▶The protective conductor system of the do-
mestic electrical installation must be prop-
erly installed.
▶Never equip the appliance with an external
switching device, e.g. a timer or remote
control.
▶When the appliance is installed, the mains
plug of the power cord must be freely ac-
cessible. If free access is not possible, an
all-pole isolating switch must be installed in
the permanent electrical installation accord-
ing to the conditions of Overvoltage Cat-
egory III and according to the installation
regulations.
▶When installing the appliance, check that
the connection cable is not trapped or
damaged.
Installation instructions en
19
17.4 General information
Follow these general instructions during the installation.
¡For the installation, observe the currently valid build-
ing regulations and the regulations of the local elec-
tricity and gas suppliers.
¡When discharging the exhaust air, the official and
legal regulations, such as the regional building
code., must be observed.
¡In order to freely access the fan box for servicing,
select an easy-to-reach installation site.
¡The surfaces of the appliance are sensitive. Avoid
damaging them during installation.
17.5 Information on the installation situation
¡Install this appliance in a worktop.
¡The appliance is not suitable for combined opera-
tion with a gas hob.
¡To install additional special accessory parts, ob-
serve the enclosed installation instructions.
¡The width of the extractor hood must correspond at
least with the width of the hob.
¡To optimally detect the cooking vapours, install the
appliance behind the hob.
To ensure that the appliance does not lose any power,
do not install any wall units above the appliance and
maintain the following clearances:
¡At least 50cm to the left and right from the appli-
ance to a wall or to an adjacent wall unit
¡At least 5cm from the frame of the appliance to a
wall
¡At least 2cm from the Guided Air suction area to a
unit wall
¡Include a ventilation opening in the base with a
cross-section of 80 cm².
Flush installation of appliances with sharp
corners
Do not install appliances with sharp edges in stone or
granite worktops.
Flush installation of appliances with rounded
corners
You can install appliances with rounded corners into
each worktop.
en Installation instructions
20
17.6 Instructions for the exhaust air pipe
The appliance manufacturer does not provide any war-
ranty for faults attributable to the pipeline.
¡Use a short, straight exhaust air pipe with as large a
pipe diameter as possible.
¡Long, rough exhaust air pipes, many pipe bends or
small pipe diameters reduce the suction power and
increase the fan noise.
¡Use an exhaust pipe that is made of non-combust-
ible material.
¡To prevent condensate from returning, fit the ex-
haust pipe with a 1° gradient from the appliance.
Note:Suitable air extraction ducts are available from
our after-sales service, your dealer or on our website.
Flat ducts
Use flat ducts with an inner cross-section that corres-
ponds to the diameter of the round pipes:
¡Diameter of 150mm corresponds to ap-
prox.177cm².
¡Diameter of 120mm corresponds to ap-
prox.113cm².
¡Use sealing strips for different pipe diameters.
¡Do not use any flat ducts with sharp bends.
Round pipes
Use round pipes with an inner diameter of 150mm (re-
commended) or at least 120mm.
17.7 Installation
Checking the units
▶Check whether the fitted unit is level and has suffi-
cient load-bearing capacity.
The maximum weight of the appliance is 40kg.
Preparing the units
Note:To install the hob and the appliance seamlessly,
you require special accessories, which are not included
in the scope of delivery. Observe the enclosed installa-
tion instructions for special accessories.
Requirement:The unit is suitable for the installation.
1. Make a cut-out in the worktop, depending on the in-
stallation position.
The angle between the cut surface and the worktop
must be 90°.
2. Ensure that the worktop has sufficient load-bearing
capacity and stability.
Use a heat- and humidity-resistant reinforcing mater-
ial for any substructure.
3. Ensure that the fitted unit is still stable after the cut-
outs have been made.
4. Remove any shavings.
5. Depending on the installation position, remove the
back panel of the fitted unit.
Preparing the appliance
WARNING‒Risk of injury!
The appliance is heavy.
▶To move the appliance, twopeople are required.
▶Use only suitable tools and equipment.
1. Place the appliance on a soft surface and remove
the transit bolt.
2. Stick the seal in the designated groove and trim
it .
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Bosch DDW88MM66/02 User manual and assembly instructions
- Category
- Cooker hoods
- Type
- User manual and assembly instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI