AVGear AVG-HD120 User manual

Brand: AVGear

Model: AVG-HD120

Type: User manual

AVG-HD120

The AVG-HD120 is a mini-size extender set

consisting of a Transmitter and a Receiver.

HDMI signal is input into the transmitter and

HDBaseT 2.0 technology is used to transmit

high-resolution1080p/4k signal to the receiver

up to 70/40m via a Cat5e/Cat6A cable. The

receiver then outputs the HDMI signal.

Features

 Ultrathin design

 Supports HDMI 1.4 & HDCP 1.4, able

to transmit signals 4Kx2K@30Hz &

1080p

 Transmits a 4Kx2K signal for 5m via

HDMI port, 40m via HDBT port

 Transmits a 1080P signal for 10m via

the HDMI port, 70m via the HDBT

port

 The Receiver is powered from the

transmitter via 12VDC PoC

technology

 Supports unidirectional IR control

 Supports HDMI LOOP output

 High Bandwidth: 10.2Gbps

 Rack mountable

AVG-HD120

PLEASE READ THIS PRODUCT MANUAL CAREFULLY

BEFORE USING THIS PRODUCT.

This manual is only for operation instruction only, and

is not to be used in a maintenance capacity. The

functions described in this version are current as at

March 2016. Any changes of functions and

operational parameters will be updated in future

manual versions. Please refer to your dealer for the

latest product details.

Version 1.0 1/03/16

AVG-HD120

SAFETY OPERATION GUIDE

In order to guarantee the reliable operation of the equipment and safety of the

user, please abide by the following procedures during installation, use and

maintenance:

1. The system must be earthed properly. Please do not use two blade plugs

and ensure the AC power supply ranges from 100v to 240v and from 50Hz

to 60Hz.

2. Do not install the units in an environment where they will be exposed to

extreme hot or cold temperatures.

3. These units will generate heat during operation, please ensure that you allow

adequate ventilation to ensure reliable operation.

4. Please disconnect the units from mains power if they will be left unused for a

long time.

5. Please DO NOT try to open the casing of the equipment, DO NOT attempt to

repair the unit. Opening the unit will void the warranty. There are high

voltage components in the unit and attempting to repair the unit could result

in serious injury.

6. Do not allow the unit to come into contact with any liquid as that could result

in personal injury and product failure.

AVG-HD120

TABLE OF CONTENTS

Introduction .............................................................................................................. 1

Introduction to the AVG-HD120 ................................................................... 1.1

Features ....................................................................................................... 1.2

What’s in the Box ........ ……………………………………………………………………2

Product Appearance of the AVG-HD120 ............................................................... 3

Transmitter .................................................................................................... 3.1

Receiver ........................................................................................................ 3.2

System Connection ................................................................................................. 4

Usage Precautions ....................................................................................... 4.1

Connection Diagram .................................................................................... 4.2

Connection Procedure.................................................................................. 4.3

Application .................................................................................................... 4.4

Specification ............................................................................................................. 5

Panel Drawing .......................................................................................................... 6

Troubleshooting & Maintenance ............................................................................ 7

AVG-HD120

1. Introduction

1.1. Introduction to the AVG-HD120

The AVG-HD120 is a mini-size extender set consists of a Transmitter and a Receiver.

HDMI signal is input into the transmitter and HDBaseT 2.0 technology is used to

transmit a high-resolution 1080p/4k signal to the receiver up to 70/40m via a

Cat5e/Cat6A cable. The receiver then outputs the HDMI signal.

Unidirectional IR and PoC power is also transmitted across the Cat5e/Cat6A cable.

1.2. Features

 Ultrathin design

 Supports HDMI 1.4 & HDCP 1.4, able to transmit signals 4Kx2K@30Hz &

1080p

 Transmits a 4Kx2K signal for 5m via the HDMI port, 40m via the HDBT port

 Transmits a 1080P signal for 10m via the HDMI port, 70m via the HDBT port

 The Receiver is powered from the transmitter via 12VDC PoC technology

 Supports unidirectional IR control

 Supports HDMI LOOP output

 High Bandwidth: 10.2Gbps

 Rack mountable

AVG-HD120

2. What’s in the Box

 1 x AVG-HD120 (includes Transmitter &

Receiver)

 4 x Mounting Brackets

 8 x Screws

 8 x Rubber Feet

 1 x Power Adapter (DC 12V 2A)

 1 x IR Emitter

 1 x IR Receiver

 1 x User Manual

Note: Please confirm if the product and the accessories are all included, if not, please

contact your dealer.

AVG-HD120

3. Product Appearance of the AVG-HD120

3.1. Transmitter

No.

Name

Description

①

Power

Illuminates red when powered on

②

IR OUT

Connect with an IR Emitter to send infrared signal, works with the

IR IN port of the Receiver.

③

HDBT OUT

RJ45 connector with green & yellow indicators. Connect to the

HDBT IN socket on the Receiver via CAT5e/ CAT6A cable,

supports unidirectional PoC.

 HDCP compliant indicator

 OFF: No HDMI traffic (no picture output)

 GREEN: HDMI Traffic contains HDCP.

 Blinking GREEN: HDMI Traffic without HDCP

 HDBT Link status indicator:

 OFF: No Link

 YELLOW:Link Successful

 Blinking YELLOW: Link Error

④

HDMI

LOOP

Connect with a HDMI display

⑤

HDMI IN

Connect with HDMI source

⑥

DC 12V

Insert a DC 12V 2A power adapter here to power both TX & RX

LINK

HDCP

HDMI LOOP

HDBT OUT

IR OUTHDMI INDC 12V

13456

AVG-HD120

3.2. Receiver

No.

Name

Description

①

Power

indicator

Illuminates red when powered on

②

IR IN

Connect with IR receiver to collect infrared signals, work with the

IR OUT port of the Transmitter.

③

HDBT IN

Connect to the HDBT OUT socket on the Transmitter via CAT5e/

CAT6A cable.

④

HDMI OUT

Connect with HDMI display.

Note: Pictures shown in this manual are only for reference.

LINK

HDCP

1234

HDMI OUT

HDBT IN

IR IN

AVG-HD120

4. System Connection

4.1. System Applications

Robust performance for control and signal transmission makes the AVG-HD120 ideal

in the custom installation industry, IT computer space, signal monitoring, big screen

displays, conference systems, television broadcast, education, banking and security

institutions etc.

4.2. Usage Precautions

1. System should be installed in a clean environment with temperature and humidity

maintained to within equipment specification.

2. All of the power switches, plugs, sockets and power cords should be insulated and

safe.

3. All devices should be connected before power is turned on.

4. Use shielded straight-thru Cat5e/Cat6Acable with TIA/EIA T568B terminations for

best transmission results.

4.3. Connection Diagram

LINK

HDCP

LINK

HDCP

Transmitter

Receiver

HDTV

Blu-ray DVD

CAT5e/ 6 Cable

HDMI Cable

DC 12V

HDMI Cable

Standby

HDTV

AVG-HD120

4.4. Connection Procedure

Step 1. Connect a HDMI source (such as Blu-ray DVD) to HDMI IN port of the

transmitter with a HDMI cable.

Step 2. Connect the HDBT OUT/PoH port of the transmitter to HDBT IN/PoH port of

the receiver through a straight-thru CAT5e/CAT6a cable.

Step 3. Connect a HDMI display (such as HDTV) to HDMI OUT port of the receiver

with a HDMI cable.

Step 4. When using IR control, do the following.

a) Connect an IR receiver to the IR IN port of the Receiver.

b) Connect an IR Emitter to the IR OUT port of Transmitter.

Step 5. Connect a DC12V power adaptor to the power port of the transmitter, the

receiver will be powered via the PoC solution.

AVG-HD120

5. Specifications

Model

Spec

Transmitter

Receiver

Input

Signal

1 x HDMI IN

1 x IR IN,

1 x HDBT IN

Connector

1 x19-pin Type-A female HDMI

1 x 3.5mm mini jack

1 x RJ-45

Output

1 x HDMI OUT;

1 x IR OUT;

1 x HDBT OUT

1 x HDMI OUT

Connector

1 x 19-pin Type-A female

HDMI

1 x 3.5mm mini jack

1 x RJ-45

1 x 19-pin Type-A female HDMI

General

Resolution Range

Up to 4K×2K@30Hz

Transmission

Mode

HDBaseT

Transmission

Distance

1080P@60Hz ≤70m

4Kx2K@30Hz ≤40m

Bandwidth

10.2Gbps

HDMI Standard

HDMI 1.4 and HDCP 1.4

Temperature

0~ 50℃

Reference

Humidity

10% ~ 90%

Power Supply

DC 12V, 2A

AVG-HD120

Power

Consumption

11W(Max)

Dimension

(W*H*D)

128x 16x 84 mm

90x 16x 84 mm

Weight

157g

116g

6. Panel Drawing

Transmitter

Receiver

LINKHDCP

HDMI LOOP

HDBT OUT

IR OUTHDMI INDC 12V

128 mm

84 mm

16 mm

HDMI OUT

HDBT IN

IR IN

LINKHDCP

90 mm

84 mm

AVG-HD120

7. Troubleshooting & Maintenance

No image on the display:

 Ensure that the display device has been set to the correct input.

 Ensure that the HDMI cables used for both the Source/Transmitter and the

Receiver/Display are properly connected and are working. Test the HDMI

cables directly from a source to the display and ensure correct operation.

 Ensure that the Cat5e/Cat6a cable has not been damaged and that it has been

terminated correctly with T568B on both ends. A temporary length of

Cat5e/Cat6 can be used for testing to ensure that the devices are compatible

and working properly.

 Ensure proper grounding of the power supply.

 Known issues with HDMI 1.2 source devices: Older compatibility (HDMI 1.2)

may result in HDBaseT transmission issues.

Colour loss or poor picture quality:

 Ensure that the HDMI cables used for both the Source/Transmitter and the

Receiver/Display are properly connected and are high quality. Test the HDMI

cables directly from a source to a display to check picture quality.

 Ensure proper grounding of the power supply.

 If the static becomes stronger or picture quality becomes worse when

connecting the video connectors, this may be due to improper grounding.

 Check the grounding and make sure all the components are properly grounded

to a common ground. Improper grounding may cause damage to the Receiver.

If your problem persists after following the above troubleshooting steps, seek further

help from your authorised dealer.

AVGear AVG-HD120 User manual

AVGear AVG-HD120 User manual

AVGear AVG-HD120 User manual

Other documents