Dyson DC07 Origin Owner's manual

Brand: Dyson

Model: DC07 Origin

Category: Vacuum cleaners

Type: Owner's manual

This manual is also suitable for

Owner’s manual

Please read this guide carefully before using your DCO7

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 1 (Cyan plate)(Yellow plate)(Black plate)(PANTONE Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Important safety instructions

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

1 Do not leave appliance when plugged in. Unplug from electrical

outlet when not in use and before servicing.

2 Do not use outdoors or on wet surfaces or to vacuum water or other

liquids – electric shock and personal injury could occur.

3 Do not allow to be used as a toy. Close attention is necessary when

used by or near children.

4 Do not allow use by anyone unable to operate the vacuum properly.

5 Use only as described in this manual. Use only with Dyson-

recommended attachments, accessories, and replacement parts.

6 Check to ensure your electricity supply corresponds to that shown on

the rating plate, which can be found on the base of the machine

between the wheels. The machine must only be used as rated.

7 If the machine is not functioning properly, has been dropped,

damaged, left outdoors, or immersed in liquid, contact the Dyson

Helpline at 1-866-693-9766.

8 Do not use with a damaged cord or plug; do not pull or carry by the

cord; do not use the cord as a handle; do not close a door on the

cord or pull the cord around sharp edges or corners. Do not run the

machine over the cord. Keep the cord away from heated surfaces

and open flames.

9 Do not unplug by pulling on the cord. To unplug, grasp the plug,

not the cord.

10 Do not handle the plug or machine with wet hands.

11 Do not use the machine without the Clear binTM and the filters

in place.

12 Do not put any objects into openings in the machine. Do not use

with any opening blocked; keep free of dust, lint, hair, and anything

that may reduce air flow.

13 Keep hair, loose clothing, fingers, and all parts of body away from

openings in the machine and moving parts such as the brushbar.

14 Do not use the machine to pick up sharp hard objects, small toys,

pins, paper clips, etc. They may damage the machine.

15 The use of an extension cord is not recommended.

16 Store the machine indoors. Put the machine away after use with the

cord wrapped safely to prevent tripping accidents.

17 Turn off all controls before unplugging.

18 Take extra care when cleaning on stairs; always work with the

machine at the bottom of the stairs. Keep vacuum on the floor.

Do not put on chairs, tables, etc.

19 Do not pick up anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

20 Do not use to pick up flammable or combustible liquids, such as

gasoline, or use in areas where they may be present.

21 When vacuuming, certain carpets may generate small static charges

in the Clear binTM or wand. These are not associated with the

electricity supply. To minimize any effect from this, do not put your

hand or insert any object into the Clear binTM unless you have first

emptied it and rinsed it out with cold water.

22 Do not carry out any maintenance or repair work other than that

shown in this manual or advised by the Dyson Helpline.

23 Consult your flooring manufacturer’s instructions before vacuuming

and caring for your flooring, rugs, and carpets. Some carpets will

fuzz if a rotating brushbar is used when vacuuming. If this happens

we recommend vacuuming in bare floors mode and consulting with

your flooring manufacturer.

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electrical

appliance, basic precautions

should always be followed,

including the following:

READ ALL INSTRUCTIONS

BEFORE USING THIS

VACUUM CLEANER

SAVE THESE

INSTRUCTIONS

THIS APPLIANCE IS INTENDED

FOR HOUSEHOLD USE ONLY

Polarization instructions

To reduce the risk of electric

shock, this appliance has a

polarized plug (one blade is

wider than the other). This plug

will fit in a polarized outlet only

one way. If the plug does not fit

fully in the outlet, reverse the

plug. If it still does not fit,

contact a qualified electrician to

install the proper outlet. Do not

change the plug in any way.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 2 (Cyan plate)(Yellow plate)(Black plate)(PANTONE Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Contents

Dyson Helpline

Important safety instructions Page 2

Assembling 4

Using your DCO7 6

Washing your filter 8

Using the tools 10

Emptying the Clear binTM 12

Clearing blockages 14

Using and maintaining optional accessories 16

Troubleshooting tips 18

Limited warranty and customer care 19

Owner’s Manual

Please read this guide carefully

before use.

Dyson Helpline contact us at

-866-693-9766

Wand release button

Cyclone release button

Airway inspection valve

Soleplate

Shroud

Wand cap

Upper cord hook

Bin emptying button

On/off switch

Washable lifetime

filter housing

Brushbar housing

Cyclone assembly

Wand

Brushbar on/off

Carry handle

Clear binTM

Hose

Lower cord hook

U-bend release button

U-bend

Wand

Upper cord hook

www.dyson.comwww.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 3 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Assembling your DCO7

This machine was inspected and

packaged carefully before being

shipped from the factory.

If you need assistance during

assembly or operation, please

call the Dyson Helpline at

1-866-693-9766.

1Slide the hose into the guides

at the back of the machine,

and click into place.

2While pressing the hose

release button, slide the

wand down inside the hose.

Box contents

Stair tool

Crevice tool

Brush tool

Wand

Hose

Dyson Helpline contact us at

-866-693-9766

Assembling

7 days a week

Additional accessories may be

included with some models.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 4 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Assembling

tip

3Slide the wand into the top

of the machine until it clicks

securely into place. You may

need to press firmly and

should hear a ‘click’ sound.

To quickly release cord,

rotate upper cord hook

downward. Twist back up

before rewinding cord.

4Push the brush and stair tools

securely into the storage holes

on either side of machine.

Fit the crevice tool into the tool

clip on the back of the wand.

34 5

5Store the cord safely by

winding it counter-clockwise

around the cord winders and

securing with the cord clip.

www.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 5 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Using your DCO7

Switching on/off

1Make sure you have read

and understood all safety

instructions before using the

machine for the first time.

The wand cap should be

closed when not using the

tools.

2Plug into electrical outlet and

press the on/off switch.

3To start vacuuming, push the

front of the cleaner head down

with your foot and tilt the

handle backward.

Using your DCO7

WARNING

• This machine is intended for

domestic use only. Fine dust

such as plaster dust or flour

should only be vacuumed in

small amounts.

• Consult your flooring

manufacturer’s instructions

before vacuuming your

flooring, rugs and carpets.

Some carpets will fuzz if a

rotating brushbar is used when

vacuuming. If this happens we

recommend vacuuming in

bare floors mode and

consulting with your flooring

manufacturer.

CAUTION

• Keep hair, loose clothing,

fingers, and all parts of the

body away from openings

and moving parts.

• This machine is fitted with

a belt protection system.

If any item becomes caught

in the brushbar (e.g., rug

fringe), you will hear a loud

“ratcheting” warning noise.

To rectify, turn the machine

off, disconnect from the

electrical outlet, and clear

any obstruction (see page 14),

checking that the brush control

is set to the correct position

for the floor surface before

re-starting the machine.

2 3

Dyson Helpline contact us at

-866-693-9766

tip

7 days a week

The ratcheting noise may also

occur if your carpet or area

rug is not adequately attached

to the floor. If this happens

you should vacuum in bare

floors mode.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 6 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Using your DCO7

Transporting your Dyson

To move the machine from room

to room, ensure it is upright,

with the cord stored on the cord

winders and the wand securely

in place. Tilt back on the rear

wheels and push forward.

Carrying your DCO7

Your DCO7 should be lifted by

using the carry handle.

CAUTION

• Do not shake the machine

when carrying.

• For your safety do not press

the cyclone release catch

when carrying your machine.

Brush control system

Ensure the machine is in an

upright position before adjusting

the setting.

1Bare floors

Use this setting to stop brushbar

from turning when vacuuming

bare floors and delicate floors,

rugs, and carpets.

2Carpets

Use this setting so brushbar

turns when vacuuming non-

delicate surfaces.

tip The brushbar will not turn until

you tilt the handle backward

to begin vacuuming.

www.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 7 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Dyson Helpline contact us at

-866-693-9766

Washing your filter

7 days a week

A Lifetime washable filter

IMPORTANT

Check your washable filter

regularly and wash at least

every 6 months according to

instructions to maintain

performance.

BLifetime HEPA filter

This is a permanent lifetime

filter. Do not remove or

attempt to rinse this filter.

Washing your filter

CAUTION

• Turn power off and unplug

before washing filter. Failure

to do so could result in

electric shock or personal

injury.

To remind you when to rinse your

washable filter, circle your two

6-monthly rinses on the sticker

provided under the Clear bin.

Removing washable filter

1Press the filter release catch

to remove the filter housing

from the machine.

2Remove the filter from the

housing.

B A

tip The filter may require more

frequent washing based on

individual vacuuming habits,

check regularly.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 8 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Washing your filter

Only the blue foam pad and the

yellow case should be rinsed –

do not wash the filter housing.

3Submerge the foam pad and

case in cold water and rinse

thoroughly.

CAUTION

• Rinse in cold water only.

• Do not use detergent.

• Do not put in a washing

machine or dishwasher.

4Rinse the blue foam pad and

squeeze gently, repeating until

the water runs clear.

5Rinse the yellow case and tap

firmly, repeating until the water

runs clear.

6Leave in a warm place to dry

for 12 hours. Make sure the

filter is completely dry before

replacing in the machine.

CAUTION

• Do not dry in an oven or

microwave.

• Do not dry in a clothes dryer.

• Do not dry near an open flame.

7When the blue foam pad and

yellow case are completely

dry, place the foam pad in the

case and replace in the filter

housing. Click back into

machine, pressing points 1

and 2firmly to secure.

CAUTION

• Do not use the machine

without the filter in place.

12 hrs

www.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 9 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Using the tools

Choosing the right tool

The tools allow you to clean

surfaces above the floor and

to reach hard to clean areas.

Ensure the machine is in an

upright position before

using tools.

ABrush tool – with soft bristles

to dislodge dust and cobwebs.

Can be used to clean vents

and some furniture.

BStair tool – with velour strips

to pick up hairs and an

agitating edge to lift the

carpet. Can be used to clean

stairs and upholstery.

CCrevice tool – reaches deep

into nooks and crannies.

Can be used to clean

along baseboards and in

tight spaces.

CAUTION

Do not use your vacuum cleaner

outdoors or on wet surfaces.

Vacuum may be used inside a

garage only when used with the

Model 08909 Dyson Car

Cleaning Kit accessories. If used

in a garage, care should be

taken to wipe the soleplate and

wheels with a dry cloth after

vacuuming to clean off any

sand, dirt, or pebbles that could

damage delicate floors.

How to clean your tools

The brush tool, stair tool, and

crevice tool may be washed in

warm water with a detergent.

Rinse and air dry thoroughly

before using. You may wipe the

outside of the floor tool or turbo

tool/mini turbine head with a

damp cloth, but do not

submerge in water. Do not

attempt to clean any tools when

they are attached to the machine.

Dyson Helpline contact us at

-866-693-9766

7 days a week

Attaching tools

Use tools for easier cleaning in hard

to reach areas.

1Press the wand release to detach

the wand from the machine.

2Pull wand up to extend hose, slide

the hose away from the wand

until the metal tube and hose cuff

click into place.

All Dyson tools can be used

in the following ways:

Wand mode

Slide back the wand cap and fit one

of the tools directly on the

wand handle.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 10 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Using the tools

tip

Hose mode

Press the hose release button and

remove the wand. Fit one of the

tools directly on to the end of

the hose.

FOR YOUR SAFETY

• When the hose is fully

extended, grasp firmly by

the hose, not the tool.

Reversed wand mode

(for selected models only)

Remove wand as shown for hose

mode. Reverse the wand and

click it into the end of the hose,

pressing the hose release button

to ensure a correct fit. Fit one

of the tools on to the end of

the wand.

The vacuum has been

designed to follow you when

used in wand or hose mode.

Stair cleaning

Use the hose and stair tool for

stair cleaning. The hose will

stretch all the way to the top of

an average staircase so you

can leave your machine at

the bottom.

CAUTION

• To avoid personal injury and

to prevent the machine from

falling when cleaning stairs,

always place it at the bottom

of the stairs.

• Powerful suction can cause

the hose to “pull back.”

Please take care using the wand.

www.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 11 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Emptying the Clear binTM

Removing the bin

Press the cyclone release catch

with your thumb to remove the

Clear binTM assembly from the

machine.

To ensure your machine continues

to clean effectively, the Clear binTM

must be emptied when the dust

reaches the level of the MAX

mark.

•When removing bin, do not

pull up on carry handle while

pressing cyclone release catch.

•When replacing the bin,

ensure it clicks back

into place.

Clear binTM emptying option 2

Emptying into a bag is

recommended for allergy

sufferers. Place bin in bag and

pull the trigger to release dust.

Let dust settle and close bin base

securely before removing from

bag and refitting cyclone and bin

on machine.

Clear binTM emptying option 1

Pull the trigger to release dust

directly into a garbage can or

wastebasket. Shake or tap firmly to

remove all dust from inside the

cyclone.

Dyson Helpline contact us at

-866-693-9766

7 days a week

Emptying the

Clear binTM

CAUTION

• Turn power off and unplug

before emptying the bin. Failure

to do so could result in electric

shock or personal injury.

• Do not use machine without

Clear binTM in place.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 12 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Emptying the Clear binTM

Shroud cleaning

(when necessary)

To remove any build-up of lint or

large dust particles on the shroud:

APress the bin release catch to

remove the Clear bin.

BClean the shroud with a cloth

or dry brush to remove the

lint and dust.

CAUTION

• Do not use the machine

without the Clear binTM in

place.

To reassemble the Clear bin,

place on the floor with the Clear

binTM base closed.

CHolding the carry handle, put

the cyclone assembly inside the

Clear bin,

TM line up the front

and rear catches, and push

down to click the catches into

place.

DEnsure the Clear binTM is

secure before replacing on

the machine.

The British Allergy Foundation is a

UK national charity with the aim of

improving awareness, prevention

and treatment of allergies.

The British Allergy Foundation Seal

of Approval is a UK registered

trademark.

Clear binTM cleaning

(optional)

IMPORTANT

• You may rinse the Clear binTM

with water. Rinse only the

Clear binTM – do not rinse the

inner cyclone, shroud, or

cones.

• Do not use detergents.

• Do not immerse any other

part of the machine in water.

• Ensure the Clear binTM is

completely dry before

replacing.

tip

www.dyson.com

Clear binTM will not come off

cyclone unless the bin base

is open.

www.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 13 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Clearing blockages

Wand

Remove wand as shown on

page 11, and press the wand

release button to remove the

wand from the hose. Check

inside wand for blockages.

CAUTION

• Beware of sharp objects

when clearing blockages.

Hose

APress the cyclone release catch

to remove the Clear binTM

assembly from the machine.

BPress the lower hose release

button from the front of

machine and slide the hose

out from the rear, holding the

lower cord winder. Check

inside the hose for blockages.

Clearing blockages

CAUTION

• Unplug the machine from the

electrical outlet before starting

to look for blockages. Failure

to do so could result in

electric shock or personal

injury.

• If any part of the machine

becomes blocked it may

overheat and then stop

automatically shut off. Unplug

machine and leave to cool

down for at least 60 minutes

before clearing the blockage.

• Regularly wipe the soleplate

and wheels with a dry cloth

after vacuuming to clean off

any sand, dirt, or pebbles that

could damage delicate floors.

• Please note: clearing

blockages is not covered by

your machine’s limited

warranty.

• Refit all parts of the machine

before using it.

Dyson Helpline contact us at

-866-693-9766

7 days a week

Tools

Check that the tools are clear of

blockages.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 14 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Clearing blockages

U-bend

• Tilt the machine forward to

slide out the U-bend.

• Check inside for blockages.

Airway inspection valve

• Squeeze the valve release

buttons to remove the airway

inspection valve.

• Check inside for blockages.

CAUTION

• The ratcheting noise may

warn that the brushbar is

obstructed. If this occurs,

unplug the machine from the

electrical outlet before

removing the obstruction.

www.dyson.com

Brushbar

Lay the machine on its front.

1Undo the colored soleplate

fasteners using a coin and

remove the soleplate.

2Clear the brushbar obstruction,

carefully cutting away any

threads with a pair of scissors.

3Replace the soleplate and

tighten the fasteners.

When replacing the soleplate,

the soleplate must be fitted

securely with the bottom of the

cleanerhead to achieve optimal

performance. Check the

alignment of the soleplate with

front edge of cleanerhead.

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 15 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Using and maintaining optional accessories

Usage

Extends and flexes to clean

awkward gaps and spaces

Using and maintaining

optional accessories

• Not all accessories available

with all models.

• Colors may vary.

CAUTION

• Do not use your vacuum

cleaner outdoors or on wet

surfaces. Vacuum may be used

inside a garage only when used

with the Model 08909 Dyson

Car Cleaning Kit accessories.

If used in a garage, care should

be taken to wipe the soleplate

and wheels with a dry cloth after

vacuuming to clean off any sand,

dirt, or pebbles that could

damage delicate floors.

Carpet – Press rear pedal

Attach low reach floor tool

to wand and recline handle

Bare floors – Press front

pedal

Low reach floor tool

Dyson Helpline contact us at

-866-693-9766

7 days a week

Flexi crevice tool

AExtend and flex

BUse with or without brush

Usage

For easier cleaning under low

furniture

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 16 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Using and maintaining optional accessories

Sprinkle Zorb onto carpet

Ensure machine is

turned off

Vacuum the carpet

Wait 30 minutes

Replace brushbars

Replace soleplate

Remove and clean

brushbars

Remove soleplate

Work into carpet pile

Usage

Carpet cleaning

Zorb carpet powder

Mini turbine head

Usage

Advanced turbine head removes dirt

from upholstery, stairs, and the car

Mini turbine head

Maintenance

www.dyson.com

APush in to stop brushbar

from spinning

BAdapter release button

not used on all models

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 17 (Cyan plate)(Magenta(PANTONE plate)(Yellow plate)(Black plate)Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Troubleshooting your Dyson

Problem Potential solution

Less than normal or no pickup • If vacuuming non-delicate carpeting, ensure brush control is

from cleanerhead or set on carpets mode. Note: brushbar will only spin when the

handle is reclined.

Machine turns off in use

• Remove and check washable filter to see if it is clean (filter

should be blue in color). Wash filter if necessary as shown

on page 8.

• If you removed the soleplate, it must be refitted flush with the

cleanerhead. If it is not, refit soleplate as shown on page 15

and re-check performance.

• Be sure the filter housing, U-bend, and airway inspection valve

are snapped in securely and confirm there are no blockages.

Less than normal or no suction • Confirm the U-bend is in place and that there are no blockages.

from wand or hose • Remove the wand and check for blockages.

• Confirm the hose has no blockages or holes by stretching it out.

• Be sure the filter housing and airway inspection valve are

snapped in securely and confirm there are no blockages.

• Remove and check washable filter to see if it is clean (filter

should be blue in color). Wash filter if necessary as shown

on page 8.

Brushbar not spinning • Ensure brush control is set on carpets mode.

Note: brushbar will only spin when the handle is reclined.

Loud ‘ratcheting’ noise coming • Ratcheting may indicate there is an obstruction in the brushbar

from cleanerhead when and is meant to protect the belt in the machine. Note: the

vacuuming ratcheting may also occur if your carpet is not adequately

attached to the floor or if your rug has loose tassels. (This noise

does not hurt the machine.)

• Check to see if there is an obstruction in the brushbar as shown

on page 15.

• Note: when refitting the soleplate it must be fitted securely.

Affix as shown on page 15.

• If there is no obstruction, you may want to set brush control

to bare floors mode.

Unit will not stand upright • Stand behind the vacuum holding the handle at a 45

degree angle.

• Locate and remove the airway inspection valve and take note

of the square plastic molding where the airway inspection valve

plugs into. (It should slide up and down.)

• Snap that square plastic piece up toward the ceiling.

• After it snaps into place, the unit will stand upright.

Refer to page 3 for an illustration of DC07. If this does not help with your problems, please call the

Dyson Helpline at 1-866-693-9766. The Helpline is open 7 days a week to answer your questions.

Dyson Helpline contact us at

-866-693-9766

7 days a week

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 18 (Cyan plate)(Yellow plate)(Black plate)(PANTONE Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Limited warranty and customer care

www.dyson.com

Thank you for choosing to buy a Dyson.

If you have a question about your Dyson vacuum cleaner, call the Dyson Helpline at

1-866-693-9766 with your serial number and details of where and when you bought

the cleaner. Your serial number can be found on the rating plate, which is on the

base of your machine between the wheels. Most questions can be solved over the

phone by one of our Helpline staff. If your machine needs service, call the Dyson

Helpline. We will discuss with you the options available for service. If your machine is

under warranty and it is a covered repair, your machine will be repaired at no cost.

To reach the Dyson Helpline call at 1-866-693-9766 toll free, or visit Dyson online

at www.dyson.com

To help us ensure you receive prompt and efficient service, please register your

purchase with us. There are two ways to do this:

• by completing and returning the enclosed form to us by mail.

• online at www.dyson.com

This will confirm ownership of your Dyson in the event of an insurance loss and

enable us to contact you if necessary. If you have any questions about your Dyson,

please call our customer helpline at 1-866-693-9766, 7 days a week, or log on to

our website at www.dyson.com

What is covered

Your Dyson vacuum cleaner is warranted against original defects in material and

workmanship for a period of five years from the date of purchase, when used for

private household purposes in accordance with the Dyson Owner’s Manual.

This warranty provides, at no extra cost to you, all labor and parts necessary to

ensure your vacuum cleaner is in proper operating condition during the warranty

period. This warranty is subject to the following terms:

What is not covered

Dyson, Inc. shall not be liable for costs incurred as a result of:

• Machines purchased from an unauthorized dealer.

• Clearing blockages from your machine.

• Use of parts not in accordance with the Owner’s Manual.

• Careless operation or handling, misuse, and/or lack of maintenance or use not in

accordance with the Owner’s Manual.

• External sources such as weather.

• Repairs or alterations carried out by unauthorized parties or agents.

• Use of the vacuum cleaner other than for normal domestic household purposes

within the United States, e.g., for commercial or rental purposes.

• Use of parts and accessories other than those produced or recommended by

Dyson, Inc.

Warranty Service

• Please fill out and return the Product Registration Form, or register online at

www.dyson.com

• Before service can take place, the terms of the warranty require that you contact

the Dyson Helpline with your model name/number, serial number, date, and place

of purchase. Please keep your purchase receipt in a safe place to ensure you have

this information.

• All work will be carried out by Dyson, Inc. or its authorized agents.

• Any replaced defective parts will become the property of Dyson, Inc.

• Service under this limited warranty will not extend the period of this warranty.

• If your machine is not functioning properly, please call the Dyson Helpline at

1-866-693-9766. Most issues can be rectified over the telephone by our trained

customer care staff. If this is not possible Dyson, Inc. will arrange for your vacuum

cleaner to be repaired and returned in full working order at no extra cost to yourself.

Dyson customer care

Limited 5 year

household warranty

Terms and Conditions of the

Dyson 5 year limited warranty

120V 60Hz 10.5A

Note your serial number for

future reference:

Your serial number can be

found on the rating plate,

which is on the base of your

machine between the wheels.

www.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 19 (Cyan plate)(Yellow plate)(Black plate)(PANTONE Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Limited warranty and customer care

This product is protected by the following intellectual property rights:

Patent/Patent Application numbers: CA 1,241,809; US 4,573,236; CA 2,312,827; US 6,526,623; CA 2,313,177; US 6,691,849; CA 2,315,078;

US 6,289,553; CA 2,325,953; US 6,425,931; US 6,461,508; CA 2,351,552; US 6,572,078; US 6,442,791; AU 2001232024; CA 2400404;

EP 1265519; JP 2001-564647; US 2003-0102619; AU 2002231965; CA 2,438,855; EP 1361813; JP 2002-567126; US 2004-0068829; AU 287872;

EP 1320317; JP 2004-509684; US 2003-0163889; AU 2002226556; CA 2,439,250; EP 1370172; JP2004-528876; US 2004-0074213;

AU 2002229966; CA 2,439,032; EP 1361812; JP 2002-567124; US 10/468,870; AU 2002226554; CA 2,438,077; EP 01370173; JP 2002-567131;

US 2004-0144070; AU 2002241151; CA 2442218; EP 1377196; JP 2004-528087; JP 2004-0112018; AU 2002225207; CA 2,438,069; EP 1361814;

JP 2004-520137; US 2004-0112022; AU 2002225232; CA 2,438,079; EP 1361815; JP 2004-520139; US 2004-0068827

Registered Design/Application numbers: CA 97332; US D475,820; CA 86192; US D427,737; US D455,242

Please note: Small details may vary from those shown.

Dyson Helpline contact us at

-866-693-9766 www.dyson.com

Warranty Limitations and Exclusions

• Any implied warranties relating to your vacuum cleaner, including but not limited

to warranty of merchantability or warranty of fitness for a particular purpose, are

limited to the duration of this warranty. This limitation is not allowed by some states

and so this limitation may not apply to you.

• Your remedy for breach of this warranty is limited to the warranty service described

above. Dyson, Inc. will not be liable for any consequential damages or incidental

damages you may incur in connection with your purchase and use of your vacuum

cleaner. This limitation is not allowed by some states and so this limitation may not

apply to you.

• This warranty gives you specific legal rights. You may also have other rights that

vary by state.

• This warranty is not transferable.

JN.16852 PN. 04482-13-01 12.06.07

Terms and Conditions (continued)

www.dyson.com

16852_DCO7_OP_MAN_US.qxd 5/7/07 14:00 Page 20 (Cyan plate)(Yellow plate)(Black plate)(PANTONE Red 032 C plate)

10:39:28 2007-07-06 C_16852_DCO7_OP_MAN_US_4c1s.pdf

Dyson DC07 Origin Owner's manual

Brand: Dyson

Model: DC07 Origin

Category: Vacuum cleaners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Dyson DC07 Origin Owner's manual

This manual is also suitable for

Dyson DC07 Origin Owner's manual

Related papers

Other documents