BH SENS S4.3K TPMS Sensor User manual

Brand
BH SENS
Model
S4.3K TPMS Sensor
Type
User manual

BH SENS S4.3K TPMS Sensor is a device designed to monitor tire pressure and transmit data wirelessly. It is typically installed inside a tire and transmits information about tire pressure, temperature, and other data to a receiver or display unit.

The sensor is powered by a built-in battery and is designed to be durable and long-lasting. It is also designed to be easy to install and can be used with a variety of tire types and sizes.

TPMS sensors are commonly used to improve safety and fuel efficiency. They can alert drivers to low tire pressure, which can help to prevent accidents and improve handling. They can also help to extend the life of tires by ensuring that they are properly inflated.

BH SENS S4.3K TPMS Sensor is a device designed to monitor tire pressure and transmit data wirelessly. It is typically installed inside a tire and transmits information about tire pressure, temperature, and other data to a receiver or display unit.

The sensor is powered by a built-in battery and is designed to be durable and long-lasting. It is also designed to be easy to install and can be used with a variety of tire types and sizes.

TPMS sensors are commonly used to improve safety and fuel efficiency. They can alert drivers to low tire pressure, which can help to prevent accidents and improve handling. They can also help to extend the life of tires by ensuring that they are properly inflated.

S4.3K sensor user manual
S4.3K sensor is transmitting module of TPMS
Product name： TPMS SENSOR
Model name： TMSS4C4
The module is powered by a built-in battery. Usually this sensor is placed in a rubber container
and then glued to the inner wall of the tire. The yellow frame below shows the sensor in the rubber
container.
Please take attention that changes or modification not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC /
CNR-102 énoncée dans un autre environnement.cette eqipment devrait être installé
et exploité avec distance minimale de 20 entre le radiateur et votre corps.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
l'appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes
aux CNR exempts de licence d’Innovation, Sciences et Développement économique
Canada. L’exploitation est soumise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage,
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
  • Page 1 1
  • Page 2 2

BH SENS S4.3K TPMS Sensor User manual

Brand
BH SENS
Model
S4.3K TPMS Sensor
Type
User manual

BH SENS S4.3K TPMS Sensor is a device designed to monitor tire pressure and transmit data wirelessly. It is typically installed inside a tire and transmits information about tire pressure, temperature, and other data to a receiver or display unit.

The sensor is powered by a built-in battery and is designed to be durable and long-lasting. It is also designed to be easy to install and can be used with a variety of tire types and sizes.

TPMS sensors are commonly used to improve safety and fuel efficiency. They can alert drivers to low tire pressure, which can help to prevent accidents and improve handling. They can also help to extend the life of tires by ensuring that they are properly inflated.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Other documents