BlendMount BBE-2017 Custom-Fit Radar Detector Mount User manual

  • Hello! I am an AI chatbot trained to assist you with the BlendMount BBE-2017 Custom-Fit Radar Detector Mount User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
PART# BBE-2017
Blend
fflount-
®
ESCORT.
BELTRONICS.
11
11
1
1111
11
111
11
1111
1111
111
11
1
Innovative
Mounting
Solutions
LEFT HAND
DRIVE
VEHICLE
7
28028
1
9702
a
INSTALLATION
INSTRUCTIONS
FOR BELTRONICSAND
ESCORT
RADAR
DETECTORS
Your rear
view
mirror
has minimal clearance between
the
back
side
of
the
mirror
and the
mirror
stem.
It
is
very
important
that
this
mount
Is Installed correctly
to
ensure
mirror
adJustablllty
Is
retained.
PLEASE READ
THESE
INSTRUCTIONS
THOROUGHLY
BEFORE
INSTALLING
THIS
MOUNT
NOTE:
For
Illustration
purpoau,
the
mount
and
rear
view
mirror
shown
In
thffe
lnatructlona
may
look
allghtly
different
then
YOUR
mount
and
rear
viaw
mirror.
RELEASE BUTTON
89fore
lnstalllng
this
mount
on
your
mirror
observe
how
the spring clip functions.
When
used
property,
the
spring
cllp
avoids
putting
excessive
prwuure
on
the
mirror
when
lnstalllng
and
removing
the
radar
detector
(RD),
To
release tension from the spring clip, simply squeeze the tab and
the back side
of
the mount together. This wlll lower the bottom portion
of
the
spring clip allowing you ID allele
the
RD
on
and
off
the
mount. Push the
RD
Releaee button and slide
the
RD
onto the Spring Cllp unlll
you
hear
It lock Into position, then release both the Tab and Release Button. Install and
remove the
RD
a
few
times before lnatalllng
the
mount
on
your
mirror.
Once
th•
lnatallatlon
la
complate,
th•
aprlng
cllp
allows
you
to
accua
th•
buttons
on
top
of
tha
RD
whil•
still
having
the
RD
installed
to
sit
as
cloaa
to
th•
bottom
of
th•
rear-viaw
mirror
as
poasibla.
By
gently pushing
down
on
the
RD
the spring clip is designed
to
flex downward allowing you
to
push desired buttons, then it will spring back into its original position when
you 'lake your finger away. This can also
be
usefull
1D
access the release button.
STEP 1 Loosen
the
clamp screw
so
the
kip
section &eperates from
the
mid section. This wlll
prwlde
the necessary clearance to slide the
mount
over
the
mirror stem
as
shown above. AdJuat
the
mirror
paralell
to
the
windahiald
and
•lightly
upward
for
Nila
of
installation.
TOPANDMID
SECTIONS MUST TOUCH
A.T
THE PIVOT POINT
BEFORE CLAMP SCREW
IS
FULLY
TIGHTENED
CLEARANCE /
FORMIRROR
~
STEM
PIVOT POINT
STEP 2 BEFORE
FULLY
TIGHTENING THE
CLAMP
SCREW,
MAKE
SURE THE TOP
AND
MID
SECTIONS
ARE
TOUCHING
A.T
THE
PIVOT POINT.
If
you
can
not
get
them
to
touch
at
the
pivot point,
you
have
an
incompatibla
mirror
typa for this
mount
PA.GE
1
OF2
PART# BBE-2017
Blend
fflount-
® ESCORT BELTRONICS .
Innovative
Mounting
Solutions
STEP 3 Position the mount
88
far folward as you
can. Tlghten the clamp
screw
untlll the
Top
and
Mid
Sections are allghtly anug around the mirror alllm.
You
should allll
be
able
to
rotate the mount.
STEP 4 Rotate the mount so
It
Is parallel with the
bottom
of
the
mirror.
Tlghten the clamp screw untlll the
mount
Is
aecunily attached
ID
the mirror stem. Do not over
tighten the clamp
screw.
CLAMP SCREW MUST
BE
SUGHTI.Y
LOOSENED
BEFORE
MAKJNG
ROTATING
ADJUSTMENT
BE
SURE TO RETIGKTEN
AFTER ADJUSTMENT IS
MADE
STEP 5 Install your radar detec:klr onto the mount. Use the adjustments shawn above
ID
adjust the
RD
ID
your
deal
red
position.
We
recommend adjusting the RD
88
close
to
the bottom
of
your mirror
as
you can.
Be
sure
ID
tighten
the
vartlcal and pivot adjustment screws
aflllr the adjustments are made. For the Pivot adjustment, grab the long arm
of
the alien wrench for maximum leverage.
You
will net
str1p
the
thraacled
holes
In
the aircraft grade alumlnum.
CAUTION
DO NOT use this mount
If
It Interferes with the adjustablllty or the operation
of
your
111ar
view mirror
In
any
way.
DO NOT use this mount
If
the radar detector creates an unsafe viewing obstruction.
DO NOT ATTEMPT
TO
MODIFY THIS
PRODUCT.
Consult
the
manufacturer
for
assistance.
All BlendMc
unt
products are accompanied with detailed lnstallatlcn Instructions and adjustment tips.
You
are encouraged to contact
cuatomeraer"1ce@blend-
mount.com or call J28 Design at 1-888-497-8388 for further asalstance.
Check the BlendMount Forum for lnatallatlon tips
and
some vehlcle specific Installs.
www.b~ndmounlcom
Innovative De
sig
n
And
Precision Manufacturing
PAGE20F2
Your feedback Is very Important
ID
us. Please email any questions or
comments you have
to
cuatomeraervlce@blendmounlcom
BlendMount-US PATENT# D625,580 S, 0656,811 S, 0653,980 S
and other patants pending
/