Gigabyte H273-Z80 User manual

H273-Z80-AAN1

H273-Z80-AAW1

High Density Server - AMD EPYC™ 9004

2U 4-Node DP 24-Bay Gen4 NVMe/SATA/SAS/SATA/ 2600W Titanium redundant power supply (AAN1)

High Density Server - AMD EPYC™ 9004

2U 4-Node DP 24-Bay Gen4 NVMe/SATA/SAS/ 3000W Titanium redundant power supply (AAW1)

User Manual

Rev. 1.0

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentation:

 User Manual: detailed information & steps about the installation, conguration and use of this

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

software component (e.g. BMC rmware, rail-kit) compatible with this product.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents.

For More Information

For related product specications, the latest rmware and software, and other information please visit our website at

http://www.gigabyte.com

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller

portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

https://esupport.gigabyte.com/ to create a new support ticket

For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:

server[email protected]

Conventions

The following conventions are used in this user's guide:

NOTE!

Gives bits and pieces of additional

information related to the current topic.

CAUTION!

Gives precautionary measures to

avoid possible hardware or software problems.

WARNING!

Alerts you to any damage that might

result from doing or not doing specic actions.

Server Warnings and Cautions

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING!

To reduce the risk of electric shock or damage to the equipment:

• Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

• Unplug all the power cords from the power supplies to disconnect power to the equipment.

WARNING!

To reduce the risk of personal injury from hot surfaces, allow the drives

and the internal system components to cool before touching them.

WARNING!

This server is equipped with high speed fans. Keep away from hazardous

moving fan blades during servicing.

WARNING!

This equipment is not suitable for use in locations where children are

likely to be present.

WARNING!

This equipment is intended to be used in Restrict Access Location. The

access can only be gained by Skilled person.

Only authorized by well trained professional person can access the

restrict access location.

CAUTION!

• Do not operate the server for long periods with the access panel open or removed. Operat-

ing the server in this manner results in improper airow and improper cooling that can lead to

thermal damage.

• Danger of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)

CAUTION!

ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU

PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,

PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-

TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER

WHEN HANDLING PARTS.

Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by

their edges without any component and pin touching. After removing a board from its protective

wrapper or from the system, place the board component side up on a grounded, static free sur-

face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over

any surface.

System power on/o: To remove power from system, you must remove the system from

rack. Make sure the system is removed from the rack before opening the chassis, adding, or

removing any non hot-plug components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be

present on power, telephone, and communication cables. Turn off the system and disconnect the

cables attached to the system before servicing it. Otherwise, personal injury or equipment dam-

age can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,

boards, and other parts. We recommend that you perform all procedures in this chapter only at

an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic

wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling

parts.

ESD and handling boards: Always handle boards carefully. They can be extremely

sensitive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a

board from its protective wrapper or from the system, place the board component side up on a

grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.

Do not slide board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased conductor that slips

over two jumper pins. Some jumpers have a small tab on top that can be gripped with ngertips

or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when

using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with

the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the

jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to

grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the

board may bend or break.

CAUTION!

Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery

only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-

teries according to the manufacturer’s instructions.

- 7 -

Table of Contents

Chapter 1 Hardware Installation ...................................................................................11

1-1 Installation Precautions .................................................................................. 11

1-2 Product Specications .................................................................................... 12

1-3 System Block Diagram ................................................................................... 17

1-4 CMC Hub Integrated Architecture .................................................................. 18

1-5 Multiplexing Management Topology ............................................................... 18

Chapter 2 System Appearance ..................................................................................... 19

2-1 Front View ...................................................................................................... 19

2-2 Rear View ....................................................................................................... 20

2-3 Front Panel LED and Buttons ........................................................................ 21

2-4 RoT LEDs ....................................................................................................... 22

2-5 Rear System LAN LEDs ................................................................................. 24

2-6 Power Supply Unit LED .................................................................................. 25

2-7 Hard Disk Drive LEDs .................................................................................... 26

Chapter 3 System Hardware Installation ......................................................................27

3-1 Installing the Hard Disk Drive ......................................................................... 28

3-2 Removing the Node ....................................................................................... 29

3-3 Removing Chassis Cover ............................................................................... 30

3-4 Removing and Installing the Fan Duct ........................................................... 31

3-5 Removing and Installing the Heatsink ............................................................ 32

3-6 Removing and Installing the CPU .................................................................. 35

3-7 Installing Memory ........................................................................................... 37

3-7-1 Twelves Channel Memory Conguration ................................................................37

3-7-2 Installing the Memory ............................................................................................38

3-7-3 Processor and Memory Module Matrix Table .........................................................38

3-7-4 Memory Population Table .......................................................................................39

3-8 Installing the PCI Expansion Card ................................................................. 40

3-9 Removing and Installing the Rear IO Card .................................................... 42

3-10 Installing the Mezzanine Card ........................................................................ 43

3-10-1 Installing the OCP 3.0 Mezzanine Card .................................................................43

3-11 Replacing the Fan Assembly .......................................................................... 44

3-12 Replacing the Power Supply .......................................................................... 45

3-13 Cable Routing ................................................................................................ 46

- 8 -

Chapter 4 Motherboard Components ...........................................................................52

4-1 Motherboard Components ............................................................................. 52

4-2 Jumper Setting .............................................................................................. 53

4-3 Backplane Board Storage Connector ............................................................. 54

4-3-1 CBPH7O1 ...............................................................................................................54

Chapter 5 BIOS Setup ..................................................................................................55

5-1 The Main Menu .............................................................................................. 57

5-2 Advanced Menu ............................................................................................. 60

5-2-1 Trusted Computing .................................................................................................62

5-2-2 PSP Firmware Versions .......................................................................................... 63

5-2-3 Legacy Video Select ...............................................................................................64

5-2-4 AST2600 Super IO Conguration ...........................................................................65

5-2-5 S5 RTC Wake Settings ...........................................................................................67

5-2-6 Serial Port Console Redirection .............................................................................68

5-2-7 CPU Conguration ..................................................................................................72

5-2-8 PCI Subsystem Settings .........................................................................................73

5-2-9 USB Conguration ..................................................................................................75

5-2-10 Network Stack Conguration ..................................................................................77

5-2-11 NVMe Conguration ...............................................................................................78

5-2-12 SATA Conguration.................................................................................................79

5-2-13 Graphic Output Conguration .................................................................................80

5-2-14 AMD Mem Conguration Status .............................................................................81

5-2-15 Tls Auth Conguration ............................................................................................82

5-2-16 RAM Disk Conguration .........................................................................................83

5-2-17 iSCSI Conguration ................................................................................................84

5-2-18 Intel(R) I350 Gigabit Network Connection ..............................................................85

5-2-19 VLAN Conguration ................................................................................................87

5-2-20 MAC IPv4 Network Conguration ...........................................................................88

5-2-21 MAC IPv6 Network Conguration ...........................................................................89

5-3 AMD CBS Menu ............................................................................................. 90

5-3-1 CPU Common Options ...........................................................................................91

5-3-2 DF Common Options ..............................................................................................97

5-3-3 UMC Common Options ........................................................................................103

5-3-4 NBIO Common Options ........................................................................................123

5-3-5 FCH Common Options .........................................................................................133

5-3-6 NTB Common Options .........................................................................................142

5-3-7 SOC Miscellaneous Control .................................................................................143

5-3-8 Workload Tuning ...................................................................................................145

5-3-9 CXL Common Options ..........................................................................................146

5-4 AMD PBS Menu ........................................................................................... 147

- 9 -

5-4-1 RAS ......................................................................................................................148

5-5 Chipset Setup Menu ..................................................................................... 150

5-5-1 North Bridge .........................................................................................................151

5-5-2 Fabric Resource ...................................................................................................152

5-6 Server Management Menu ........................................................................... 154

5-6-1 System Event Log ................................................................................................156

5-6-2 View FRU Information ..........................................................................................157

5-6-3 BMC Network Conguration .................................................................................158

5-6-4 IPv6 BMC Network Conguration .........................................................................159

5-7 Security Menu .............................................................................................. 160

5-7-1 Secure Boot .........................................................................................................161

5-8 Boot Menu .................................................................................................... 163

5-9 Save & Exit Menu ......................................................................................... 165

5-10 BIOS Recovery ............................................................................................ 166

5-11 BIOS POST Beep code (AMI standard) ....................................................... 167

5-11-1 PEI Beep Codes ...................................................................................................167

5-11-2 DXE Beep Codes .................................................................................................167

- 10 -

This page intentionally left blank

- 11 -

Hardware Installation

1-1 Installation Precautions

The motherboard/system contain numerous delicate electronic circuits and components which

can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully

read the user manual and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap, keep your hands dry and rst touch a metal object to eliminate static electricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

.

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

Hardware Installation

- 12 -

1-2 Product Specications

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

System

Dimension

2U 4-Node - Rear access

440 (W) x 87.5 (H) x 877(D) mm

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

CPU AMD EPYC™ 9004 series processor family

Dual processor, 5nm technology

Up to 96-core, 192 threads per processor

Supports CPU 240W at ambient 30°C

NOTE: If only 1 CPU is installed, some PCIe or memory functions might be unavailable

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Socket Per Node:

2 x LGA 6096

Total:

8 x LGA 6096

Socket SP5

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Chipset System on Chip

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Security UEFI Secure Boot

Silicon root of trust

SNMP Support: V3

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Memory Per Node:

24 x DIMM slots

Total:

96 x DIMM slots

DDR5 memory supported only

12-Channel memory architecture

RDIMM modules up to 96GB supported

3DS RDIMM modules up to 256GB supported

Memory speed: Up to 4800 MHz

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

LAN Per Node:

2 x 1GbE LAN ports (1 x Intel® I350-AM2)

Supported NCSI function

1 x Dedicated management port

Total:

8 x 1GbE LAN ports (1 x Intel® I350-AM2)

Supported NCSI function

4 x Dedicated management ports

*Spanning Tree Protocol (STP) must be enabled in LAN switch function if using

ring topology

NOTE:

We reserve the right to make any changes to the product specications and product-related

information without prior notice.

- 13 -

Hardware Installation

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Video Integrated in Aspeed® AST2600

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Management chip on CMC board:

Integrated in Aspeed® AST2520A2-GP

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Storage Per node:

6 x 2.5" Gen4 NVMe/SATA/SAS hot-swappable bays

(NVMe from CPU_1, SATA from CPU_0)

Total:

24 x 2.5" Gen4 NVMe/SATA/SAS hot-swappable bays

SAS card is required for SAS devices support

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

SAS Supported via add-on SAS Card

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Expansion Slots Per node:

Riser Card CRSH01Q:

1 x PCIe x16 (Gen5 x16) low-prole slot, from CPU_0

Riser Card CRSH01R:

1 x PCIe x16 (Gen5 x16) low-prole slot, from CPU_0

1 x OCP 3.0 mezzanine slot with PCIe Gen5 x16 bandwidth, from CPU_0

Supports NCSI function

*1 x M.2 slot:

M-key

PCIe Gen4 x4, from CPU_0

Supports NGFF-2280/22110 cards

Total:

Riser Card CRSH01Q x 4:

4 x PCIe x16 (Gen5 x16) low-prole slots, from CPU_0

Riser Card CRSH01R x 4:

4 x PCIe x16 (Gen5 x16) low-prole slots, from CPU_0

4 x OCP 3.0 mezzanine slot with PCIe Gen5 x16 bandwidth, from CPU_0

Supports NCSI function

*4 x M.2 slot:

M-key

PCIe Gen4 x4, from CPU_0

Supports NGFF-2280/22110 cards

*Optional kit for M.2 extension riser card/PN: 9CMTP192NR-00

Hardware Installation

- 14 -

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Internal I/O Per Node:

1 x TPM header

1 x OCP slot

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Front I/O Per node:

1 x Power button with LED

1 x ID button with LED

1 x Status LED

1 x System reset button

Total:

4 x Power button with LED

4 x ID button with LED

4 x Status LED

4 x System reset button

*1 x CMC status LED

*1 x CMC reset button

*Only one CMC status LED and reset button per system

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Rear I/O Per node:

2 x USB 3.2 Gen1

1 x Mini-DP

2 x RJ45

1 x RJ45 MLAN

1 x Node Status LED

Total:

8 x USB 3.2 Gen1

4 x Mini-DP

8 x RJ45

4 x RJ45 MLAN

4 x Node Status LED

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Backplane I/O Speed and bandwidth:

PCIe Gen4 x4 or SATA 6Gb/s or SAS 12Gb/s

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

TPM 1 x TPM header with SPI interface

Optional TPM2.0 kit: CTM010

Hardware Installation

- 15 -

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Power Supply

(AAN1)

Dual 2600W (240V) 80 PLUS Titanium redundant power supply

AC Input:

100-127V~/ 13.8A, 50-60Hz

200-240V~/ 15A, 50-60Hz

DC Input:

240Vdc/ 15A

DC Output:

Max 1000W/ 100-127V~

+12.2V/ 81A

+12.2Vsb/ 4.5A

- Max 2600W/ 200-220V

+12.2V/ 213A

+12Vsb/ 4.5A

System power supply requires C19 type power cord

(AAW1) Dual 3000W (240V) 80 PLUS Titanium redundant power supply

AC Input:

100-127V~/ 16A, 50-60Hz

200-240V~/ 16A, 50-60Hz

DC Input:

240Vdc/ 16A

DC Output:

Max 1200W/ 100-127V~

+ 12.2V/ 98.36A

+ 12.2Vsb/ 3A

Max 2600W/ 200-207V~

+ 12.2V/ 213A

+ 12.2Vsb/ 3A

Max 3000W/ 208-240V~

+ 12.2V/ 245.9A

+ 12.2Vsb/ 3A

System power supply requires C19 type power cord

Hardware Installation

- 16 -

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

System

Management

Aspeed® AST2600 management controller

GIGABYTE Management Console (AMI MegaRAC SP-X) web interface

Dashboard

HTML5 KVM

Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)

Sensor Reading History Data

FRU Information

SEL Log in Linear Storage / Circular Storage Policy

Hardware Inventory

Fan Prole

System Firewall

Power Consumption

Power Control

LDAP / AD / RADIUS Support

Backup & Restore Conguration

Remote BIOS/BMC/CPLD Update

Event Log Filter

User Management

Media Redirection Settings

PAM Order Settings

SSL Settings

SMTP Settings

Socket

Security

Security Server Operating Properties

Power SupplySystem fan

Operating

Properties

Operating temperature: 10°C to 35°C

Operating humidity: 8-80% (non-condensing)

Non-operating temperature: -40°C to 60°C

Non-operating humidity: 20%-95% (non-condensing)

- 17 -

Hardware Installation

1-3 System Block Diagram

• Please Go to Chapter 4 Motherboard Components for Riser Slot information.

MDI

Rear IO board

MCIO 4i

PCIe3.0 x2

MDI

2 x 1G LAN

COM

PCIe5.0 x16

PCIe5.0 x16 LP slot

Riser CRSH01Q

PCIe5.0 x16

2 x USB3.2 Gen1

Mini-DP

RGMII

Mini-DP

MDI MLAN

RTL8365MB

LAN Hub

NCSI

Switch

BMC

ASPEED

AST2600

Intel

I350-AM2

SPI

PCIe2.0 x1

USB2.0 x1

TPM

USB Hub

12-Channel DDR5, 12 x DIMMs

Speed up to 4800 MHz

12-Channel DDR5, 12 x DIMMs

Speed up to 4800 MHz

xGMI3 32GT/s

4 x16 GOP

PCIe5.0 x16 LP slot

Riser CRSH01R

PCIe4.0 x4

PCIe4.0 x12

Riser CMTP192 (option)

PCIe5.0 x16

SATAIII x6

OCP 3.0

CPU0

AMD EPYC™ 9004

Socket SP5

CPU1

AMD EPYC™ 9004

Socket SP5

USB3.2 Gen1

6-bay 2.5” Gen4 NVMe/SATA per node

M.2

To CMC

LAN Hub

Hardware Installation

- 18 -

1-4 CMC Hub Integrated Architecture

1-5 Multiplexing Management Topology

Multiplexing Management Example

To access CMC, connect the management LAN port of each node.

Spanning Tree Protocol (STP) must be enabled in LAN switch function if using ring topology.

LAN Hub

(RTL8365MB)

LAN

Hub

LAN

Hub

LAN

Hub

LAN

Hub

MLAN

CMC

(AST2520)

BMC

(AST2600)

BMC

(AST2600)

BMC

(AST2600)

BMC

(AST2600)

Centralized

Server Management

Node 1Node Bridge Board

Node 2

Node 3

Node 4

- 19 -

System Appearance

Chapter 2 System Appearance

2-1 Front View

• Please Go to Chapter 2-3 Front Panel LED and Buttons for detail description of function

LEDs.

NODE1 NODE2 NODE3 NODE4

1 1

HDD 0

HDD 1

HDD 2

HDD 3

HDD 4

HDD 5

HDD 6

HDD 7

HDD 8

HDD 9

HDD 10

HDD 11

HDD 12

HDD 13

HDD 14

HDD 15

HDD 16

HDD 17

HDD 18

HDD 19

HDD 20

HDD 21

HDD 22

HDD 23

No. Description

1. Front Panel LEDs and buttons

NOTE! Drives with green latches support NVMe.

System Appearance

- 20 -

2-2 Rear View

No. Description

1. PCIe Slot

2. Node System Status LED

3. Mini DP Port

4. 2 x USB 3.2 Gen1

5. GbE LAN Port x 2

6. BMC Server Management LAN Port

7. OCP 3.0 Slot (SFF Type)

8. PCIe Slot

78 234

5

6 1

PSU1

PSU2

SLOT2SLOT3

SLOT1

Page is loading ...

Gigabyte H273-Z80 User manual

Gigabyte H273-Z80 User manual

Related papers

Other documents