Bald Eagle BE1003 Owner's manual

Brand
Bald Eagle
Model
BE1003
Type
Owner's manual
Introduction
Made of solid birch, this sturdy workbench is ideal for
reloading, gun adjustments, and repair jobs.
Specifications
• Construction ...............Solid Block-Laminated Birch
• Finish ...................................... Lacquer Sealed
• Dimensions ........... 54"Lx21"Wx3"T(w/2"Flange)
• WorkbenchHeightAboveFloor ....................... 36"
• LowerShelfHeightAboveFloor ...................... 22"
• LowerShelfDimensions ............343⁄4" L x 141⁄4" W"
• WorkbenchTableThickness .............................1"
• WorkbenchTableFlangeWidth ........................1"
• WorkbenchTableFlangeHeight ........................2"
• MaximumLoad(Total) ............................ 350 lbs
• MaximumLoad(WorkbenchTopOnly) ......... 225 lbs
• MaximumLoad(LowerShelfOnly) ............. 125 lbs
• ReloadingBenchWeight ............................64 lbs
Component Inventory (Figure 2) Qty
A. WorkbenchTopAssembly .................................1
B. LowerShelfAssembly .....................................1
C. Shelf Support ...............................................2
D. StandAssembly ............................................2
Hardware Inventory (Figure 3) Qty
E. BedBoltsM8-1.25X120(Stand) ........................4
F. LockWashers8mm(Stand) ..............................4
G. HexNutsM8-1.25(Stand) ................................4
H. Half-MoonSpacers(Stand) ...............................4
I. FlatWashers8mm(Stand) ...............................4
J. DowelPins10X40mm(Stand) ..........................8
K. BedBoltsM6-1X55(WorkbenchTop) .................6
L. LockWashers6mm(WorkbenchTop) ...................6
M. FlatWashers6mm(WorkbenchTop) ...................6
N. HexWrench4mm ..........................................1
O. HexWrench5mm ..........................................1
Figure 1. Model BE1003.
E
F
H
G
IJ
KLM
N
O
Figure 3.Hardwareinventory.
Figure 2.Componentinventory.
A
B
C
D
Model BE1003
Bald Eagle™ Reloading Bench
Instruction Sheet
Phone#:(360)734-3482•OnlineTechSupport:tech-support@shopfox.biz•Web:www.shopfox.biz
COPYRIGHT © SEPTEMBER, 2010 BY WOODSTOCK INTERNATIONAL, INC. REVISED APRIL, 2011 (TR)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in Taiwan#13251CRBLTSJB
-2-
Bald EagleTM
BE1003 Reloading Bench Instructions
Assembly
Usingtheinventorylistasaguide,layoutallcomponents,
andgrouptheassociatedfastenerswiththerelevant
component.Next,readthis entire assembly section before
you begin the installation procedure below.Doingthis
will ensure that assembly is completed correctly without
damaging any parts.
To assemble the unit, do these steps:
1. Ontheinsidefaceofbothstandassemblies,insert
the eight dowel pins, as shown in Figure 4.
2. Placean8mmlockwasherandflatwasheroneach
of the four M8-1.25 X 120 bed bolts.
3. Insert the bed bolts through both stand assemblies,
so the bed bolts protrude in the same direction as
the dowels, as shown in Figure 4.
Lock
Washer
Dowel
Pin
Bed
Bolt
Flat
Washer
Figure 4. Stand assembly.
Half-Moon
Spacer
Hex Nut
Shelf
Support
Shelf
Support
Figure 5. Shelf support installation.
4. Placeeachofthefourhalf-moonspacersintheshelf
support holes (see Figure 5),sothearcisfacing
toward the end of the shelf support.
5. Select a shelf support, orient the shelf slot upward,
as shown in Figure 5, and slide the shelf support
onto the protruding dowels and bed bolt on the
stand assembly.
6. Holdtheshelfsupportengagedwiththedowelsas
shown in Figure 5, and thread an M8-1.25 hex nut
onto the end of the bed bolt, which now will be
protruding from the half-moon spacer. Tighten the
screw.
-3-
BE1003 Reloading Bench Instructions
Bald EagleTM
7. RepeatSteps 5–6 on the remaining shelf support.
8. Orientthelowershelfassemblysothesmoothside
is up, and slide the shelf into the shelf support slots,
as shown in Figure 6.
9. Install the remaining stand assembly onto the shelf
supports, as shown in Figure 6, in the same manner
as you performed Step 6.
Shelf Panel
Stand
Figure 6. Lower shelf installation.
10. Using the packaging as a means to protect the
workbench surface from being scratched, place the
workbench table face down on the floor.
11. Placetheassembledshelfandstandontothetable
underside, as shown in Figure 7.
12. Placea6mmlockwasherandflatwasheroneachof
the six M6-1 X 55 bed bolts.
13. Insert the bed bolts through both stand assemblies,
as shown in Figure 7.
14. Tighten the bed bolts.
Table Top
Flat
Washer
Lock
Washer
Bed Bolt
Figure 7. Workbench table installation.
Safety & Correct Use
• Neverexceedmaximumworkbenchloadrating.
• Do not apply an unbalanced load on the workbench
that could result in it tipping.
• Keep unsupervised children away from the
workbench.
• Donotstandorclimbontheworkbench.
• Do not use workbench outdoors or in wet or damp
locations.
• Donotleaveragsorotheritemsthataredampwith
water,oil,paint,orsolventsontheworkbench.
• Donotweldontheworkbench.
Figure 8.Assembledworkbench.
15. Turn the workbench upright onto its stand (Figure
8),thenlightlymoistenaclothwithwaterandwipe
down all surfaces.
-4-
Bald EagleTM
BE1003 Reloading Bench Instructions
REF PART # DESCRIPTION QTY REF PART # DESCRIPTION QTY
1 XBE100301 BED BOLT M8-1.25 X 120 4 9 XPAW04M HEX WRENCH 4MM 1
2 XPLW04M LOCK WASHER 8MM 4 10 XBE100310 HALF-MOON BED SPACER 4
3 XPW01M FLAT WASHER 8MM 4 11 XBE100311 DOWEL PIN 10 X 40MM 8
4 XPAW05M HEX WRENCH 5MM 1 12 XBE100312 TABLE TOP ASSEMBLY 1
5 XPN03M HEX NUT M8-1.25 4 13 XBE100313 LOWER SHELF ASSEMBLY 1
6 XBE100306 BED BOLT M6-1 X 55 6 14 XBE100314 SHELF SUPPORT 2
7 XPLW03M LOCK WASHER 6MM 6 15 XBE100315 STAND ASSEMBLY 2
8 XPW03M FLAT WASHER 6MM 6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Model BE1003 Parts
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Bald Eagle BE1003 Owner's manual

Brand
Bald Eagle
Model
BE1003
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents