AMG AMG2242 Instruction Sheet

AMG
Brand
AMG
Model
AMG2242
Type
Instruction Sheet

This manual is also suitable for

AMG AMG2242 is a standalone video transmitter with bi-directional audio and data RS232 capabilities. It features a 75 ohm BNC socket video connection with an input impedance of 75 ohms and an input level of 1 volt p-p nominal. The optical connection utilizes an ST Style connector with a wavelength of 850nm nominal. The data connection employs a 14-way push-in connector strip, supporting solid conductors up to 0.5mm2 (20 AWG). The device requires a power supply of +12 volts to +18 volts at 250mA, with a connection via a connector strip on pins 3 (Gnd) and 4 (Power Input).

AMG AMG2242 is a standalone video transmitter with bi-directional audio and data RS232 capabilities. It features a 75 ohm BNC socket video connection with an input impedance of 75 ohms and an input level of 1 volt p-p nominal. The optical connection utilizes an ST Style connector with a wavelength of 850nm nominal. The data connection employs a 14-way push-in connector strip, supporting solid conductors up to 0.5mm2 (20 AWG). The device requires a power supply of +12 volts to +18 volts at 250mA, with a connection via a connector strip on pins 3 (Gnd) and 4 (Power Input).

AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 1 of 2 D03702-00
AMG2242S
Instruction Sheet
AMG2242S Standalone Video Transmit + Bi-directional Audio + Data RS232
Video Connection
Connectors ...........................75 ohm BNC Socket.
Input Impedance...................75 ohm terminated.
Input Level ...........................1 volt p-p nominal.
Frequency Response.............10Hz to 6MHz min.
Optical Connection
Connectors............................ST Style (1 off)
Opto Out Launch Power
50/125............................-20dBm. min.
62.5/125.........................-17dBm min.
Wavelength...........................850nm nominal.
Data Connection
Connector .............................Push-in connector strip - 14way
(Solid conductors 0.5mm2(20 awg) can be connected by simply push fitting
into the appropriate connection hole. Smaller conductors and wires (up to
0.5mm2, 20 awg) are inserted into the connection space whilst depressing the
orange lever. Wire or conductors should be stripped back to a length of
11mm. Use a small screwdriver to depress the orange lever to release the
connection.)
VIDEO INPUT Opto OUT
(Single Fibre not fitted
Opto IN
(IN/OUT Single Fibre)
SYSTEM 2000
Video
Transceiver
134mm
148mm
7mm
39.5mm
79mm A A
PL1
PIN 1
PIN 14
AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 2 of 2 D03702-00
Pinout ...................................See Below – Note Pins number from the BNC connector
Pin No. Function
1 NC
2 NC
3 Power Ground
4 Power Input (+12v to +18v dc )
5 Ground
6 Audio Input
Data
Interface RS232
7 Data Ground
8 Data Out
9 Data In
10 N/C
11 N/C
12 Audio Ground
13 Audio Output (+)
14 Audio Output (-)
Power Supply
Supply...................................+12 volt to +18 volt at 250mA
Connection ...........................Connector Strip
Pin 3 Gnd, Pin 4 Power Input
Dimensions
See Drawing Above
Mounting Details
See Drawing Above
  • Page 1 1
  • Page 2 2

AMG AMG2242 Instruction Sheet

AMG
Brand
AMG
Model
AMG2242
Type
Instruction Sheet
This manual is also suitable for

AMG AMG2242 is a standalone video transmitter with bi-directional audio and data RS232 capabilities. It features a 75 ohm BNC socket video connection with an input impedance of 75 ohms and an input level of 1 volt p-p nominal. The optical connection utilizes an ST Style connector with a wavelength of 850nm nominal. The data connection employs a 14-way push-in connector strip, supporting solid conductors up to 0.5mm2 (20 AWG). The device requires a power supply of +12 volts to +18 volts at 250mA, with a connection via a connector strip on pins 3 (Gnd) and 4 (Power Input).

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers