2. Home
  3. Domestic appliances
  4. Climate control
  5. Thermostats
  6. Honeywell
  7. FocusPRO TH5000 Series
FocusPRO TH5000 Series

Honeywell FocusPRO TH5000 Series Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Honeywell FocusPRO TH5000 Series Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
O
•§'
a©
£#
:-
0)
^
Pr-
O
C9
1^
5^'
a
•r>
aj
*»
. •
#
I
to
c
o
o
Of
o
$ $ $ g
S
g
IS
?
i
.*
5
J1
7,
o
o
I
#
a-
^
J1
3
in
3.
•r
c
cr
<?
to
D
3
O
«
$
;
f
oo
i
^ ^ ^
f
o
o
o
5*
/
f
o
3
o
.5"
CO
ra
O
1>
FocusPRO* TH5000 Series
About your new thermostat
Thermostat features 2
Setup at a glance 3
Quick reference to controls 4
Quick reference to display 5
Programming & Operation
Fan setting (auto/on) 6
System setting (heat/cool/auto) 7
Auto-changeover (heat/cool) 8
Compressor protection 9
w9
mm
Appendices iEgg
Battery replacement 10 fjp||
In case of difficulty 11 |g|
Customer assistance 13 l|^|
Accessories/replacement parts 13 il|||
5-year
limited warranty 14
CAUTION:
EQUIPMENT DAMAGE
HAZARD. To prevent possible
compressor damage, do not operate
cooling system when outdoor
temperature is below 50oF (10oC).
69-1923EFS-01
Operating Manual
About your new thermostat
Congratulations on the purchase of your new Honeywell thermostat. It has been
fH designed to give you many years of reliable service and easy-to-use, push-button
climate control.
11
Features
• One-touch temperature control.
• Large, clear, backlit display is easy to read—even in the dark.
• Displays both room temperature and temperature setting.
• Removable battery holder for fast, easy replacement.
• Built-in compressor protection.
FocusPRO* TH5000 Series
Jh is therm ostat i s ready to go! M
^&
ill
Your new thermostat is pre-programmed by the installer and ready to use. Just check ^Jg
the settings below and change if needed: "mj*
1-
Fan (Auto/On): Preset to Auto To change, seepage 6.
Auto is the most commonly used setting, but you may
prefer On for improved air circulation.
2.
System (Heat/Cool/Auto/Em. Heat); Preset to Heat ...7b change, see page 7.
You can select heating or cooling, or set the system
to control both systems automatically, if needed.
69-1923EFS-01
Operating Manual
Digital display (see page 5)
M29dG5
Function Buttons
Press to select the function displayed just above each
button.
(Functions change depending on the task.)
Battery holder (see page 10)
Temperature Buttons
Press to set preferred
temperature
69-1923EFS-01
FocusPRO* TH5000 Series
Quick reference to display screen
Low battery warning (see page 10)
Current inside
temperature
Fan setting
Auto/On (see page 6)
Auxiliary heat (Only for heat
pumps with auxiliary heat)
Replace
Battery
•^vr'#-'
/ihr.--
W? /^Setting:
rFah
Autd;
.'Sysfemj
''J'-'-
[
MCRigjae
Function buttons
Press the button beneath each function to view or change
settings (functions change depending on the task)
Temperature
setting
System status
Heat On/Cool On
(If flashing, see page 9)
System setting
Heat/Cool/Auto/Off/
Em Heat (see page 7)
pi
1^1
Jit
69-J923EFS-0r
Operating Manual
Select the fan setting
Fan
Auto
m
}
'Fan On
Press the FAN button to select Auto or On,
tn "Auto" mode (the most commonly used
setting), the fan runs only when the heating
or cooling system is on. If set to "On," the fan
runs continuously.
MCR29*07
69-7923E/rS-0?
FocusPRO" TH5000 Series
Select th e system setting
.
^
-''
Fan'
AtitO;
( Fan;.
:Autd;
•i
.'/'
•r
•-' '•-
~5\
if}
j
••j; .-J
\
•
System
Heat
• •
'X'..-.
• ^'V . -,
•m K
' vX'J
WW*
Cool
V
-•Zljf&'f'
. J:
J
'<'
"?-
WCRa^GS
Note:
The Auto and Em Heat
system settings may not
appear, depending on how
your thermostat was installed
Press the SYSTEM button to select:
• Heat: Thermostat controls only the
heating system.
• Cool: Thermostat controls only the
cooling system,
• Off: Heating and cooling systems are off
• Auto: Thermostat automatically selects
heating or cooling depending on the
indoor temperature.
• Em Heat (only for heat pumps with
auxiliary heat) Thermostat controls
Emergency and Auxiliary Heat,
Compressor is locked out-
69-1923EFS-01
Operating Manual
Auto changeover (heat/cool)
Fan
:AutQ/.„ 1, vJLSystem
Auto
MC^29A0^
Press until screen
d/spfays "Auto"
Note:
The Auto system setting may
not appear, depending on how your
thermostat was installed.
Auto Changeover is a feature used in climates
where both air conditioning and heating are
used on the same day When the system is set
to Auto, the thermostat automatically selects
heating or cooling depending on the Indoor
temperature-
Heat and cool settings must be at least 3
degrees apart. The thermostat will automati-
cally adjust settings to maintain this 3-degree
separation (called "deadband")-
The 3-degree separation between heating and
cooling set temperatures is fixed, and cannot
be changed.
69-1923EFS-Q1 8
FocusPRO* TH5000 Series
Inside w v;,:Setlirig..;.;
' -•.
•••' •.'
M29410
Message flashes until safe
restart time has elapsed
This feature helps prevent damage to the
compressor in your air conditioning or heat
pump system.
Damage can occur if the compressor Is
restarted too soon after shutdown. This fea-
ture forces the compressor to wait for a few
minutes before restarting.
During the wait time, the display will flash
the message Cool On (or Heat On if you have
a heat pump). When the safe wait time has
elapsed,
the message stops flashing and the
compressor turns on.
ll
69-1923EFS-01
Operating Manual
S Press and pull to remove
Battery;
Insert fresh alkaline batteries,
then reinstall battery holder
TH5110D-AAA alkaline
batteries.
TH5320U/TH5220D -
AA alkaline batteries.
69-1923EFS-01
L
Batteries are optional (to provide backup
power) if your thermostat was wired to run on
AC power when installed.
Install fresh batteries immediately when the
REPLACE BATTERY warning begins flashing. The
warning flashes about two months before the
batteries are depieted,
Even if the warning does not appear, you
should replace batteries once a year, or before
leaving home for more than a month.
Batteries provide backup power to the display
during power interruptions All settings are
permanently stored in memory, and do not
require battery power
10
FocusPRO* TH5000 Series
If you have difficulty with your thermostat, please try the following suggestions.
Most problems can be corrected quickly and easily,
Display is blank
Temperature
settings do not
change
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is on.
• Make sure furnace door is closed securely.
• If thermostat is battery-powered, make sure fresh AA or AAA alkaline
batteries (depending on model) are correctly installed (see page 10).
Make sure heating and cooling temperatures are set to acceptable ranges:
• Heat: 40° to 90oF (4.5° to 320C).
• Cool: 50° to 990F (10° to 370C).
11 69-1923EFS-.01
Operating Manual
\ Heating or
cooling system
]
does not respond
Press SYSTEM button to set system to Heat. Make sure the temperature
Is set higher than the Inside temperature.
Press SYSTEM button to set system to Cool. Make sure the temperature
is set lower than the Inside temperature.
Check circuit breaker and reset if necessary.
Make sure power switch at heating & cooling system is on.
Make sure furnace door is closed securely.
Wait 5 minutes for the system to respond.
"Cool On" or
"Heat On" is
flashing
Compressor protection feature is engaged. Wait 5 minutes for the system
to restart safely, without damage to the compressor (see page 9).
69-1923EFS-01 12
Co
CO
\
—±
to
in
I
o
o
<
O"
CD
O
o
-a
o
"O
TD
"O
a
p
D3
3.
5-
3-
o o o
o
o
to
CO
o
o
o
o
o
o
ro
CO
CJI
en
o
o o
o
o
co
ro
o o
OF
CO
Ul
o
o
o
o
J
o
o
Operating Manual
Honeywell warrants this product, excluding battery, to be free from defects in the
mM workmanship or materials, under normal use and service, for a period of five (5) years
gfrom the date of purchase by the consumer. If at any time during the warranty period
the product is determined to be defective or malfunctions, Honeywell shall repair or
: replace it (at Honeyweirs option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from
which you purchased it; or
(ii) call Honeywell Customer Care at
1
-800-468-1502. Customer Care will make the
determination whether the product should be returned to the following address:
Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN
55422,
or whether a replacement product can be sent to you.
69-1923EFS-01 14
/