Kendo M Wet, Kendo S Wet, Kendo L Wet, & Kendo XL Wet - Installation Instructions
Models KMW-XX, KSW-XX, KLW-XX, & KXLW-X
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3.24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.7
0 6 212 0 2 3
1 / 5
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Kendo M Wet with fixed clip mounting
Kendo M Wet with fixed clip mounting
Kendo M Wet, Kendo S Wet, Kendo L Wet, & Kendo XL Wet - Installation Instructions
Models KMW-XX, KSW-XX, KLW-XX, & KXLW-X
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3.24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.7
0 6 212 0 2 3
2 / 5
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
fixture flathead screw
fixed mounting clip
fixed mounting clip
fixed 45 degree
mounting clip
surface
4” 4”
every 30”
to power supply
to power supply
to power supply
end power feed with wire leads
side power feed with wire leads
bottom power feed with wire leads
fixture
fixed mounting clip
pass through hole
for power feed
Quick Connect/
Wire Lead
dimensions
Male quick
connect end
Female quick
connect end
Wire lead
surface
fixture 1 fixture 2lead wires
fixture 1 fixture 2lead wires
fixture 1 fixture 2lead wires
2
1
1.1 Determine the location of where the fixture(s) will be installed. Lay the fixture(s) on the surface, and make any necessary reference marks for
the fixed mounting clips (or if using the fixed 45° degree mounting clip). Make marks 4” from each end of the fixture(s) and also every 30”
in between.
1.2 Lay the fixed clip onto the reference mark points and secure using the provided hardware.
2.1 If necessary make any pass through holes for wire lead/connector to the surface, depending on the power feed option. Then snap the
fixture into the fixed mounting clip to secure in place. Diagram on the right side illustrates the common way of connecting multiple fixtures
to each other, depending on the location of the power feed wires.
Fixed mounting clip installation
Kendo M Wet, Kendo S Wet, Kendo L Wet, & Kendo XL Wet - Installation Instructions
Models KMW-XX, KSW-XX, KLW-XX, & KXLW-X
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3.24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.7
0 6 212 0 2 3
3 / 5
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
1
2
Adjustable hinge mounting clip installation
1.1 Determine the location of where the fixture(s) will be installed. Lay the fixture(s) on the surface, and make reference marks for the mounting
clips. Make marks 4” from each end of the fixture(s) and also every 30” in between.
1.2 Slightly loosen the 2 screws on the side on adjustable bracket. Lay the bracket onto the reference mark points and secure using the
provided hardware.
2.1 If necessary make any pass through holes for wire lead/connector to the surface, depending on the power feed option. Then rotate fixture
to the appropriate degree, followed by tightening the screws on the side. Then snap the fixture into the fixed mounting clip to secure in
place. Diagram on the right side illustrates the common way of connecting multiple fixtures to each other, depending on the location of the
power feed wires.
fixture
flathead screw
loosen screws
adjustable hinge
mounting clip
4” 4”
every 30”
to power supply
to power supply
to power supply
end power feed with wire leads
side power feed with wire leads
bottom power feed with wire leads
fixture 1 fixture 2lead wires
fixture 1 fixture 2lead wires
fixture 1 fixture 2lead wires
fixture
adjustable
hinge bracket
bottom power feed
Quick Connect/
Wire Lead
dimensions
Male quick
connect end
Female quick
connect end
Wire lead
surface
Kendo M Wet, Kendo S Wet, Kendo L Wet, & Kendo XL Wet - Installation Instructions
Models KMW-XX, KSW-XX, KLW-XX, & KXLW-X
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3.24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.7
0 6 212 0 2 3
4 / 5
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
light fixture
male quick connect
female quick connect
wire leads
t
o
p
ow
e
r s
upp
l
y
t
o
p
ow
e
r s
up
p
l
y
class ll
power
supply
120 VAC 24 VDC to fixture
Connect to power
1.1 Follow one of the two options to connect the fixture to the power
supply.
1 2
Option 1- Secure female quick connect to male quick connect. Feed male
quick connect wire through conduit to power supply.
Option 2- Feed wire whip to the power supply.
1.1 Follow one of the two options to connect the fixture
to the power supply.
Kendo M Wet, Kendo S Wet, Kendo L Wet, & Kendo XL Wet - Installation Instructions
Models KMW-XX, KSW-XX, KLW-XX, & KXLW-X
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3.24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.7
0 6 212 0 2 3
5 / 5
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
power supply
low voltage wires
fixture 1
power supplies at the
end of the run
power supplies in the
middle of the run
consecutive layout,
NOT RECOMMENDED
fixture 1
fixture 1
fixture 2
fixture 2
fixture 2
low voltage wires
low voltage wireslow voltage wires
power supply
power supplypower supply
Multiple powerfeed layouts
-
1
-
2
-
3
-
4
-
5
luminii Kendo M Graze Wet Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI