Mode AVIC Z2 Owner's manual

Page is loading ...

1

Important Safety Information

ABOUT THIS MANUAL

This manual explains how to install this navigation system in your vehicle. Operation of this navigation system

is explained in the separate Operation Manual or Hardware Manual for the navigation system. Before operating

this navigation system, be sure to read them.

PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE

Do not attempt to install or service your navigation system by yourself. Installation or

servicing of the navigation system by persons without training and experience in elec-

tronic equipment and automotive accessories may be dangerous and could expose you

to the risk of electric shock or other hazards.

1. Read this manual fully and carefully before installing your navigation system.

2. Keep this manual handy for future reference.

3. Pay close attention to all warnings in this manual and follow the instructions carefully.

4. This navigation system may in certain circumstances display erroneous information regarding the

position of your vehicle, the distance of objects shown on the screen, and compass directions. In addi-

tion, the system has certain limitations, including the inability to identify one-way streets, temporary

traffic restrictions and potentially unsafe driving areas. Please exercise your own judgment in the light

of actual driving conditions.

5. As with any accessory in your vehicle’s interior, the navigation system should not divert your atten-

tion from the safe operation of your vehicle. If you experience difficulty in operating the system or

reading the display, please make adjustments while safely parked.

6. Please remember to wear your seat belt at all times while operating your vehicle. If you are ever in an

accident, your injuries can be considerably more severe if your seat belt is not properly buckled.

7. Certain government laws may restrict the placement and use of navigation systems in your vehicle.

Please comply with all applicable laws and regulations in the installation and operation of your navi-

gation system.

English
Español
Deutsch
Français
Italiano
Nederlands
Important Safety Information.................... 1
ABOUT THIS MANUAL.................................. 1
PLEASE READ ALL OF THESE 
INSTRUCTIONS REGARDING 
YOUR NAVIGATION 
SYSTEM AND RETAIN THEM 
FOR FUTURE REFERENCE .................... 1
Connecting the System  ............................ 3
Before installing this navigation system ............ 4
To prevent damage ............................................ 5
Parts supplied .................................................... 6
Connecting the system ...................................... 7
Connecting the multi-channel processor ............9
Connecting the power cord (1) ........................ 11
Connecting the power cord (2) ........................ 13
When connecting to separately sold power 
amp .......................................................... 15
When connecting a rear view camera  ............ 17
When connecting the external video component 
.................................................................. 18
When connecting the external unit featuring video
source ........................................................18
When connecting the rear display ....................19
-
When using a rear display connected to rear
video output
Installation ................................................ 20
To guard against electromagnetic 
interference .............................................. 21
Before installing  .............................................. 21
Installing this navigation system ...................... 22
-
Installation notes
-
Parts supplied
-
Installation using the screw holes on the side
of the navigation unit
Installing the GPS antenna  .............................. 25
-
Installation notes
-
Parts supplied
-
When installing the antenna inside the vehi-
cle (on the rear shelf)
-
When installing the antenna outside the vehi-
cle (on the body)
Installing the microphone..................................28
-
Parts supplied
-
Mounting on the sun visor
-
Installation on the steering column
Adjusting the microphone angle ......................29
After Installing this Navigation System
.............................................................. 30
2
Contents

Connecting the System

3

Pioneer does not recommend that you install your navigation system yourself. We

recommend that only authorized Pioneer service personnel, who have special training

and experience in mobile electronics, set up and install this navigation system.

NEVER SERVICE THIS NAVIGATION SYSTEM YOURSELF. Installing or ser-

vicing this navigation system and its connecting cables may expose you to the risk of

electric shock or other hazards, and can cause damage to the navigation system that

is not covered by warranty.

• If you decide to perform the installation yourself, and have special training

and experience in the mobile electronics installations, please carefully follow

all of the steps in the Installation Manual.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare

wiring to remain exposed.

• Do not directly connect the yellow lead of this navigation system to the vehi-

cle battery. If the lead is directly connected to the battery, engine vibration

may eventually cause the insulation to fail at the point where the wire passes

from the passenger compartment into the engine compartment. If the yellow

lead’s insulation tears as a result of contact with metal parts, short-circuiting

can occur, resulting in considerable danger.

• It is extremely dangerous to allow the GPS antenna cable or microphone

cable to become wound around the steering column or shift lever. Be sure to

install this navigation system, its cables, and wiring away in such a way that

they will not obstruct or hinder driving.

• Make sure that the cables and wires are routed and secured so they will not

interfere with or become caught in any of the vehicle’s moving parts, espe-

cially the steering wheel, shift lever, parking brake, sliding seat tracks, doors,

or any of the vehicle’s controls.

English

Español

Deutsch

Français

Italiano

Nederlands

4

Connecting the System

• Do not route wires where they will be exposed to high temperatures. If the

insulation heats up, wires may become damaged, resulting in a short circuit

or malfunction and permanent damage to the navigation system.

• Do not cut the GPS antenna cable to shorten it or use an extension to make it

longer. Altering the antenna cable could result in a short circuit or malfunc-

tion.

• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse

resister or filter, etc.) may fail to work properly.

• Never feed power to other electronic products by cutting the insulation of the

power supply lead of the navigation system and tapping into the lead. The

current capacity of the lead will be exceeded, causing overheating.

• The black lead is ground. Please ground this lead separately from the ground

of high-current products such as power amps. Do not ground more than one

product together with the ground from another product. For example, you

must separately ground any amplifier unit away from the ground of this

navigation system. Connecting grounds together can cause a fire and/or

damage the products if their grounds became detached.

Before installing this navigation system

• This navigation system is for vehicles with a 12-volt battery and negative grounding.

Check the battery voltage of your vehicle before installation.

• To avoid shorts in the electrical sys-

tem, be sure to disconnect the (–)

battery cable before beginning

installation.

5

Connecting the System

To prevent damage

• When disconnecting a connector, pull the connector itself. Do not pull the lead, as you

may pull it out of the connector.

• This navigation system cannot be installed in a vehicle that does not have an ACC

(accessory) position on the ignition switch.

• When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse

holder.

• To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the

unused speaker leads without fail. There is a possibility of a short-circuit if the leads are

not insulated.

• Attach the connectors of the same color to the corresponding colored port, i.e., blue con-

nector to the blue port, black to black, etc.

• Refer to the owner’s manual for details on connecting the power amp and other units,

then make connections accordingly.

• Since a unique BPTL circuit is employed, do not directly ground the ≠ side of the

speaker lead or connect the ≠ sides of the speaker leads together. Be sure to connect the

≠ side of the speaker lead to the ≠ side of the speaker lead on this navigation system.

• If the RCA pin jack on this navigation system will not be used, do not remove the caps

attached to the end of the connector.

• Speakers connected to this navigation unit must be high-power with minimum rating of

50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance

values other than those noted here may result in the speakers catching fire, emitting

smoke, or becoming damaged.

• When the ignition switch is turned on (ACC ON), a control signal is output through the

blue/white lead. Connect to an external power amp’s system remote control terminal

(max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even

if the audio source is switched off.

• When an external power amp is being used with this system, be sure not to connect the

blue lead to the amp’s power terminal. Likewise, do not connect the blue lead to the

power terminal of the auto antenna. Such connection could cause excessive current drain

and malfunction as well as damage to the auto antenna of the vehicle.

• When the “Auto ANT” mode is set to “Radio”, the vehicle’s antenna can be stowed or

turned off by following the instructions below.

– Change the source from radio (AM or FM) to another source

– Turn the source off

– Turn off the ignition switch (ACC OFF)

• If the “Auto ANT” mode is set to “Power”, the vehicle’s antenna can be stowed or

turned off only when the ignition switch is turned off (ACC OFF).

No ACC positionACC position

O

N

S

T

A

R

T

O

F

A

C

O

N

S

T

A

R

T

O

F

English
Español
Deutsch
Français
Italiano
Nederlands
6
Parts supplied
MicrophoneRCA connector 2
(CONNECTOR 2)
<
☞
See Page 7, 9, 17, 19>
RCA connector 1
(CONNECTOR 1)
<
☞
See Page 9, 12, 15, 18>
GPS antennaExtension lead 
(for speed signal)
Extension lead 
(for reverse signal)
ConnectorPower cord
<
☞
See Page 11, 13, 17>
The navigation unit

7

Connecting the System

Connecting the system

AV-BUS cable

(supplied with TV tuner)

IP-BUS cable

(supplied with TV tuner)

Black

Bluetooth unit (ND-BT1)

(sold separately)

Antenna

jack

Vehicle

antenna

The navigation unit

Red

Hide-away TV tuner

(e.g. GEX-P5700TV)

(sold separately)

Light gray

5 m (16 ft. 5 in.)

GPS antenna

Blue

Black

Microphone input

20 cm (7-7/8 in.)

Not used.

Microphone

(supplied)

RCA connector 2

Jack for Wired Remote

Control Adapters

(WIRED REMOTE INPUT)

Please see the Instruction

Manual for the Wired

Remote Control Adapters

(sold separately).

4 m

Black

8

English

Español

Deutsch

Français

Italiano

Nederlands

iPod adapter

(e.g. CD-IB100II)

(sold separately)

with SIRIUS satellite radio tuner)

Black

To IP-BUS inputTo IP-BUS input

To IP-BUS output

IP-BUS cable

Pioneer compatible SIRIUS satellite

radio tuner (e.g. SIR-PNR2)

(sold separately)

IP-BUS cable

(supplied with iPod adapter)

Blue

Black

Blue

Multi-CD player

(sold separately)

Blue

XM DATA cable

(supplied with hide-away XM tuner)

* When combining this navigation system with

GEX-P10XMT (sold separately), this

connection must be required.

* When installing the XM tuner in the

trunk, etc., the extension cable (e.g. CD-

600DC) (sold separately) is required.

iPod with

Dock Connector

Dock connector port

(supplied with hide-away XM tuner)

IP-BUS cable

(supplied

Black

Hide-away XM tuner

(e.g.GEX-P10XMT)

(sold separately)

• To avoid the risk of accident and the potential violation of

applicable laws, this navigation system should never be used

while the vehicle is being driven except for navigation purpos-

es. Also Rear Displays should not be in a location where it is a

visible distraction to the driver.

• In some countries or states the viewing of images on a display

inside a vehicle even by persons other than the driver may be

illegal. Where such regulations apply they must be obeyed

and this navigation system’s video source or TV features

should not be used.

Note:

The XM tuner and SIRIUS satellite radio tuner will not

receive their service when you drive outside of their

coverage area.

9

Connecting the System

Connecting the multi-channel processor

Black

Optical cable connection box

(supplied with multi-channel processor)

Blue

(GUIDE SP OUT)

Guide speaker

(e.g. CD-TS37GP)

(sold separatly)

The navigation unit

20 cm (7-7/8 in.)

Blue

Light Gray

(DIGITAL OUTPUT)

RCA connector 2

23 cm (9 in.)

RCA

connector 1

Secure the connector using the screw

supplied with multi-channel processor.

Yellow/black (GUIDE ON)

When combining this navigation unit

with the multi-channel processor system,

connect this lead to yellow/black lead on

the multi-channel processor controller

unit. In this way, when the mute signal is

output from this navigation system, the

audio volume is automatically muted or

attunated.

Note:

When Pioneer multi-channel processor (sold separately) is

connected to this navigation system, make sure the “5.1 Ch

Setup” mode is activated. Please find the correct setting by

referring to “Switching the 5.1ch setting” in the Operation

Manual of the navigation system.

10

English

Español

Deutsch

Français

Italiano

Nederlands

RCA cable (supplied with Multi-channel

processor controller unit)

Optical cable

(supplied with

multi-channel processor)

IP-BUS cable

(supplied with multi-channel processor)

Black

Blue

Multi-channel processor

(e.g. DEQ-P8000)

(sold separately)

Blue

RCA cable

(supplied with

multi-channel

processor)

Multi-channel

processor

controller unit

(e.g. AXM-P8000)

(Hide away unit)

Multi-channel processor

controller unit

(e.g. AXM-P8000)

(Display unit)

Subwoofer output

or non-fading output

(SUBWOOFER OUTPUT or

NON-FADING OUTPUT)

OPT.IN 2

Note:

Be sure that “DIGITAL OUTPUT” of this navigation system

is connected to “OPT.IN 2” of the multi-channel processor

via optical cable.

11

Connecting the System

Connecting the power cord (1)

Fuse (10 A)

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Red

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Black (ground)

To vehicle (metal) body.

Orange/white

To lighting switch

terminal.

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

White

White/black

Gray

Gray/black

Green

Green/black

Violet

Violet/black

Front speaker Front speaker

Left Right

+

≠

+

≠

+

≠

+

≠

Rear speaker or

Subwoofer (4

Ω

)

Rear speaker or

Subwoofer (4

Ω

)

Note:

When a subwoofer is connected to this navigation

system instead of a rear speaker, change the rear

output setting in the Initial Setting. (Refer to the

Operation Manual.) The subwoofer output of this

navigation system is monaural.

+

≠

Violet

Violet/black

Green

Green/black

Not used.

Subwoofer (4 Ω)

× 2

When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of

this navigation unit. Do not connect anything with Green and Green/black leads.

12

English

Español

Deutsch

Français

Italiano

Nederlands

Blue

To Auto-antenna relay control terminal.

If the vehicle has a glass antenna, connect to

the antenna booster power control terminal

(max. 300 mA 12 V DC).

The navigation unit

Note:

The antenna will automatically retract or turn off, yet the

timing varies depending on the setting. (Refer to page 5.)

For more detailed information on changing the “Auto ANT”

mode, refer to “Switching the auto antenna setting” in the

Operation Manual.

Yellow/black

If you use equipment with a mute function, connect that

equipment to the Audio Mute lead. If not, keep the Audio Mute

lead free of any connections.

Note:

Audio source will be set to mute or attenuate, while the

following sounds will not be muted or attenuated. For details,

see the Operation Manual.

- voice guidance of the navigation

- incoming Ringtone and incoming voice of the cellular

phone that is connected to this navigation system via

Bluetooth wireless technology

RCA connector 1

16 cm (6-1/4 in.)

Power cord

Note:

Cords for this navigation system and those for other prod-

ucts may be different colors even if they have the same

function. When connecting this navigation system to

another product, refer to the supplied manuals of both

products and connect cords that have the same function.

Pink (CAR SPEED SIGNAL INPUT)

The mobile navigation system is connected here to detect the distance

the vehicle travels. Always connect the vehicle’s speed detection

circuit or the ND-PG1 speed pulse generator, sold separately. Failure

to make this connection will increase errors in the location display.

IMPROPER CONNECTION MAY RESULT IN SERIOUS

DAMAGE OR INJURY INCLUDING ELECTRICAL SHOCK,

AND INTERFERENCE WITH THE OPERATION OF THE

VEHICLE’S ANTILOCK BRAKING SYSTEM, AUTOMATIC

TRANSMISSION AND SPEEDOMETER INDICATION.

LIGHT GREEN LEAD AT POWER

CONNECTOR IS DESIGNED TO DETECT

PARKED STATUS AND MUST BE

CONNECTED TO THE POWER SUPPLY SIDE

OF THE PARKING BRAKE SWITCH.

IMPROPER CONNECTION OR USE OF THIS

LEAD MAY VIOLATE APPLICABLE LAW

AND MAY RESULT IN SERIOUS INJURY OR

DAMAGE.

Light green

Used to detect the ON/OFF status of the parking brake. This lead

must be connected to the power supply side of the parking brake

switch. If this connection is made incorrectly or omitted, certain

functions of your navigation system will be unusable.

• It is strongly suggested that the speed pulse wire be connected

for accuracy of navigation and better performance of interlock.

• If the speed pulse wire is unavailable for some reason, it is

recommended that the pulse generator (ND-PG1) be used.

Note:

The position of the speed detection circuit and the position of the

parking brake switch vary depending on the vehicle model. For

details, consult your authorized Pioneer dealer or an installation

professional.

13

Connecting the System

Connecting the power cord (2)

Connection method

Clamp the parking brake

switch power supply side lead.

Clamp firmly with

needle-nosed pliers.

Power supply side

Ground side

Parking brake switch

Speed detection circuit lead

Vehicle injection

computer

Connector

Pass the extension cord

and the lead for the

speed detection circuit

through this hole.

Clamp firmly

with needle-

nosed pliers.

Close the cover.

Connection method

Be sure to use only the supplied extension lead. Use of another lead

could cause fire, smoke and/or damage this navigation system.

14

English

Español

Deutsch

Français

Italiano

Nederlands

Note:

Cords for this product and those for other products

may be different colors even if they have the same

function. When connecting this product to another

product, refer to the supplied manuals of both prod-

ucts and connect cords that have the same function.

Power cord

Violet/white (REVERSEGEAR SIGNAL INPUT)

This is connected so that the navigation system can

detect whether the vehicle is moving forwards or

backwards. Connect the violet/white lead to the

lead whose voltage changes when the shift lever is

put in reverse. Unless connected, the sensor may

not detect your vehicle traveling forward/backward

properly, and thus the position of your vehicle

detected by the sensor may be misaligned from the

actual position.

Connection method

Clamp the backup light lead.

Clamp firmly with

needle-nosed pliers.

Backup

light lead

Fuse resistor

Check the position of your vehicle’s

backup light (the one that lights up

when the shift lever is in reverse [R])

and find the backup light lead in the

trunk.

The navigation unit

Extension lead

(for reverse signal)

Extension lead (for speed signal)

For information on other leads

5 m (16 ft. 5 in.)

☞

See Page 11.

5 m (16 ft. 5 in.)

Note:

When you use the ND-PG1 speed pulse gener-

ator (sold separately), please make sure to con-

nect this lead.

When you use a rear view camera, please

make sure to connect this lead. Otherwise you

cannot switch to rear view camera picture.

☞

See Page 17.

15

Connecting the System

When connecting to separately sold power amp

The navigation unit

Front output

(FRONT OUTPUT)

Subwoofer output

or non-fading output

(SUBWOOFER OUTPUT or

NON-FADING OUTPUT)

Rear output

(REAR OUTPUT)

15 cm (5–7/8 in.)

23 cm (9 in.)

Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

Do not connect this lead to Auto-antenna control

terminal.

15 cm (5–7/8 in.)

RCA connector 1

15 cm (5-7/8 in.)

16

English

Español

Deutsch

Français

Italiano

Nederlands

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

+

≠

+

≠

+

≠

+

≠

+

≠

+

≠

System remote control

RCA cables

(sold separately)

Front speaker

Rear speaker

Subwoofer

Front speaker

Rear speaker

Subwoofer

Left Right

Perform these connections when using

the optional amplifier.

Note:

You can change the RCA output of the subwoofer depending on your subwoofer

system. (Refer to the Operation Manual.)

When connecting a rear view camera

When using this navigation system with a rear view camera, automatic switching to video

from a rear view camera is possible when the gear shift is moved to REVERSE (R) position.

Rear view mode also allows you to check what is behind you while driving.

USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE

MAY RESULT IN INJURY OR DAMAGE.

• The screen image may appear reversed.

• The rear view camera function is to use this navigation system as an aid to keep an eye on trailers,

or backing into a tight parking spot. Do not use this function for entertainment purposes.

• The object in rear view may appear closer or more distant than in reality.

• Please note that the edges of the rear view camera images may differ slightly according to whether

full screen images are displayed when backing, and whether the images are used for checking the

rear when the vehicle is moving forward.

17

Connecting the System

Fuse resistor

20 cm (7-7/8 in.)

Extension lead (for reverse signal)

5 m (16 ft. 5 in.)

Violet/white

Power cord

Rear view

camera

RCA cable

(sold separately)

To video output

Connect to the rear view camera. Do not connect

to any other equipment.

Note:

The navigation unit

RCA connector 2

Brown

(REAR VIEW CAMERA IN)

Note:

It is necessary to set to “Camera

Input” in “System Settings” when

connecting the rear view camera. (For

details, see the Operation Manual.)

Be sure to use only the supplied extension lead.

Use of another lead could cause fire, smoke

and/or damage this navigation system.

About connection method

☞

See Page 13.

When connecting the external video component

• It is necessary to set “AV Input” in “System Settings” to “Video” when connecting the

external video component. (For details, refer to the Operation Manual.)

When connecting the external unit featuring video source

• It is necessary to set “AV Input” in “System Settings” to “EXT” when connecting the

external video component. (For details, refer to the Operation Manual.)

The navigation unit

RCA cable

(sold separately)

To IP-BUS output

IP-BUS cable (sold separately)

Yellow

(VIDEO INPUT)

Pioneer external unit

(sold separately)

To video output

Black

Blue

RCA connector 1

20 cm (7-7/8 in.)

The navigation unit

RCA

RCA connector 1

cables

(sold separately)

To audio outputs

Yellow

(VIDEO INPUT)

Red, white

(AUDIO INPUT)

External

component

(sold separately)

video

To video output

20 cm (7-7/8 in.)

18

English

Español

Deutsch

Français

Italiano

Nederlands

19

Connecting the System

When connecting the rear display

When using a rear display connected to rear video output

NEVER install the rear display in a location that enables the driver to watch the

video source while driving.

This navigation system’s rear video output is for connection of a display to enable passen-

gers in the rear seats to watch the video source.

You can switch the rear screen mode in “AV Source Menu”. (For details, refer to the

Operation Manual.)

Note:

The map screen navigation images output to the rear display differ from standard NTSC format

images. Therefore, their quality will be inferior to the images that appear on the front display.

The navigation unit

RCA

RCA connector 2

15 cm (5-7/8 in.)

23 cm (9 in.)

cables

(sold separately)

To audio inputs

Yellow

(REAR MONITOR OUTPUT)

Red, white

(REAR MONITOR OUTPUT)

Rear display with

RCA input jacks

To video input

Installation

Pioneer does not recommend that you install or service your navigation system

yourself. Installing or servicing the navigation system may expose you to risk

of electric shock or other hazards. Refer all installation and servicing of your

navigation system to authorized Pioneer service personnel.

• Never install this navigation system in places, or in a manner that where:

* It could injure the driver or passengers if the vehicle stops suddenly.

* It may interfere with the driver’s operation of the vehicle, such as on the

floor in front of the driver’s seat, or close to the steering wheel or shift

lever.

• Make sure there is nothing behind the dashboard or paneling when drilling

holes in them. Be careful not to damage fuel lines, brake lines, electronic

components, communication wires or power cables.

• When using screws, do not allow them to come into contact with any electri-

cal lead. Vibration may damage wires or insulation, leading to a short circuit

or other damage to the vehicle.

• To ensure proper installation, use the supplied parts in the manner specified.

If any parts other than the supplied ones are used, they may damage internal

parts of this navigation system or they may work loose and the navigation

system may become detached.

• It is extremely dangerous to allow the GPS antenna lead or microphone lead

to become wound around the steering column or shift lever. Be sure to install

this navigation system in such a way that it will not obstruct driving.

• Make sure that leads cannot get caught in a door or the sliding mechanism of

a seat, resulting in a short circuit.

• Please confirm the proper function of your vehicle’s other equipment follow-

ing installation of the navigation system.

• Certain government laws may prohibit or restrict the placement and use of

this system in your vehicle. Please comply with all applicable laws and regu-

lations regarding the use, installation and operation of your navigation sys-

tem.

• Do not install this navigation system where it may (i) obstruct the driver’s

vision, (ii) impair the performance of any of the vehicle’s operating systems

or safety features, including airbags, hazard lamp buttons or (iii) impair the

driver’s ability to safely operate the vehicle.

20

English

Español

Deutsch

Français

Italiano

Nederlands

Page is loading ...

Mode AVIC Z2 Owner's manual

This manual is also suitable for

Mode AVIC Z2 Owner's manual

in other languages

Related papers

Other documents