Alpine CDE-7858 User manual

EN

FR

ES

IT

SE

R

Meiyi Printing Factory, Dalian, China

No. 28 Chang Qing Street, Xi Gang District, Dalian, China

ALPINE ELECTRONICS, INC.

Tokyo office: 1-1-8 Nishi Gotanda,

Shinagawa-ku,

Tokyo 141-8501, Japan

Tel.: (03) 3494-1101

ALPINE ELECTRONICS OF AMERICA, INC.

19145 Gramercy Place, Torrance,

California 90501, U.S.A.

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF CANADA, INC.

Suite 203, 7300 Warden Ave. Markham,

Ontario L3R 9Z6, Canada

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS FRANCE S.A.R.L.

(RCS PONTOISE B 338 101 280)

98, Rue De La Belle Etoile, Z.I. Paris Nord Il

B.P. 50016 F-95945, Roissy, Charles De Gaulle

Cedex, France

Tel.: 01-48 63 89 89

ALPINE ELECTRONICS OF U.K., LTD.

13 Tanners Drive, Blakelands, Milton Keynes

MK14 5BU, U.K.

Tel.: 01908-61 15 56

ALPINE ELECTRONICS DE ESPAÑA, S.A.

Portal De Gamarra 36, Pabellón 32

01013 Vitoria (Alava)-Apdo. 133, Spain

Tel.: 34-45-283588

ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.

6-8 Fiveways Boulevarde Keysborough,

Victoria 3173, Australia

Tel.: (03) 9769-0000

ALPINE ELECTRONICS GmbH

Kreuzerkamp 7-11 40878 Ratingen, Germany

Tel.: 02102-45 50

ALPINE ITALIA S.p.A.

Via C. Colombo 8, 20090 Trezzano Sul Naviglio

MI, Italy

Tel.: 02-48 47 81

CDE-7859

CDE-7858

CDE-7856

Designed by ALPINE Japan

Printed in China (Y)

68P01434K22-O

• OWNER'S MANUAL

Please read before using this equipment.

• MODE D'EMPLOI

Veuillez lire avant d’utiliser cet appareil.

• MANUAL DE OPERACIÓN

Léalo antes de utilizar este equipo.

FM/AM Compact Disc Receiver

Page is loading ...

1-EN

Contents

Operating Instructions

WARNING

WARNING.................................................. 2

CAUTION................................................... 2

PRECAUTIONS ......................................... 2

Basic Operation

Detaching the Front Panel................................. 4

Attaching the Front Panel ................................. 4

Initial System Start-Up ..................................... 4

Turning Power On and Off ............................... 4

Subwoofer On and Off (CDE-7859 only)......... 5

Subwoofer On and Off (CDE-7858/

CDE-7856 only) ............................................ 5

Adjusting Volume/Bass/Treble/

Balance (Between Left and Right)/

Fader (Between Front and Rear) ................... 5

Turning Loudness On/Off (CDE-7856 only) .... 5

Audio Mute Function........................................ 6

BBE Mode On/Off

(CDE-7859/CDE-7858 only) ........................ 6

Displaying Time................................................ 7

Setting Time ...................................................... 7

Changing Audio Level Display Pattern

(CDE-7859 only) ........................................... 7

Setting the Bass Control (CDE-7859 only) ...... 8

Setting the Treble Control (CDE-7859 only).... 8

Setting Bass Frequency

(CDE-7858/CDE-7856 only) ........................ 8

ENGLISH

Radio Operation

Manual Tuning .................................................. 9

Automatic Seek Tuning .................................... 9

Manual Storing of Station Presets .................. 10

Automatic Memory of Station Presets............ 10

Storing into Direct Access Preset (D.A.P.)

Band............................................................. 11

Tuning to Preset Stations ................................ 11

CD Player Operation

Inserting/Ejecting Disc ................................... 12

Normal Play and Pause ................................... 12

Music Sensor (Skip)........................................ 12

Fast Forward and Backward ........................... 12

Repeat Play ..................................................... 13

M.I.X. (Random Play) .................................... 13

Scanning Programs ......................................... 13

Displaying and Scrolling CD Text

(CDE-7859 only) ......................................... 13

Information

In Case of Difficulty ....................................... 14

Specifications.................................................. 15

Installation and Connections

Warning........................................................... 16

Caution............................................................ 16

Precautions...................................................... 16

Installation ...................................................... 17

Connections .................................................... 18

LIMITED WARRANTY

2-EN

WARNING

The exclamation point within an equilateral

triangle and "WARNING" are intended to alert

the user to the presence of important

operating instructions.

Failure to heed the instructions will result in

severe injury or death.

DO NOT OPERATE ANY FUNCTION THAT TAKES

YOUR ATTENTION AWAY FROM SAFELY DRIVING

YOUR VEHICLE.

Any function that requires your prolonged attention

should only be performed after coming to a complete stop.

Always stop the vehicle in a safe location before

performing these functions. Failure to do so may result in

an accident.

KEEP THE VOLUME AT A LEVEL WHERE YOU CAN

STILL HEAR OUTSIDE NOISE WHILE DRIVING.

Failure to do so may result in an accident.

MINIMIZE DISPLAY VIEWING WHILE DRIVING.

Viewing the display may distract the driver from looking

ahead of the vehicle and cause an accident.

DO NOT DISASSEMBLE OR ALTER.

Doing so may result in an accident, fire or electric shock.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE

GROUND.

(Check with your dealer if you are not sure.) Failure to do

so may result in fire, etc.

KEEP SMALL OBJECTS SUCH AS BATTERY OUT

OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If

swallowed, consult a physician immediately.

USE THE CORRECT AMPERE RATING WHEN

REPLACING FUSES.

Failure to do so may result in fire or electric shock.

DO NOT BLOCK VENTS OR RADIATOR PANELS.

Doing so may cause heat to build up inside and may result

in fire.

USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.

Use for other than its designed application may result in

fire, electric shock or other injury.

WARNING

CAUTION

The exclamation point within an equilateral

triangle and "CAUTION" are intended to alert

the user to the presence of important

operating instructions.

Failure to heed the instructions can result in

injury or material damage.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS.

Failure to do so may cause personal injury or damage to

the product. Return it to your authorized Alpine dealer or

the nearest Alpine Service Center for repairing.

PRECAUTIONS

Temperature

Be sure the temperature inside the vehicle is between

+60°C (+140°F) and –10°C (+14°F) before turning your

unit on.

Moisture Condensation

You may notice the CD playback sound wavering due to

condensation. If this happens, remove the disc from the

player and wait about an hour for the moisture to

evaporate.

Damaged Disc

Do not attempt to play cracked, warped, or damaged

discs. Playing a bad disc could severely damage the

playback mechanism.

Maintenance

If you have problems, do not attempt to repair the unit

yourself. Return it to your Alpine dealer or the nearest

Alpine Service Station for servicing.

DO NOT PLACE HANDS, FINGERS OR FOREIGN

OBJECTS IN INSERTION SLOTS OR GAPS.

Doing so may result in personal injury or damage to the

product.

3-EN

Never Attempt the Following

Do not grip or pull out the disc while it is being pulled

back into the player by the automatic reloading

mechanism.

Do not attempt to insert a disc into the unit when the unit

power is off.

Inserting Discs

Your player accepts only one disc at a time for playback.

Do not attempt to load more than one disc.

Make sure the label side is facing up when you insert the

disc. Your player will automatically eject any disc that is

inserted incorrectly. If the player continues to eject a

correctly inserted disc, push the Reset switch (located

behind the detachable front panel) with a pointed object

such as a ball-point pen.

Playing a disc while driving on a very bumpy road may

result in skips, but this will not scratch the disc or damage

the player.

New Discs

As a protective measure to prevent the CD from jamming,

the CD player will automatically eject discs with irregular

surfaces or inserted incorrectly. When a new disc is

inserted into the player and ejected after initial loading,

using your finger, feel around the inside of the center hole

and outside edge of the disc. If you feel any small bumps

or irregularities, this could inhibit proper loading of the

disc. To remove the bumps, rub the inside edge of the hole

and outside edge of the disc with a ball-point pen or other

such instrument, then insert the disc again.

Irregular Shaped Discs

Be sure to use round shape discs only for this unit and

never use any special shape discs.

Use of special shape discs may cause damage to the

mechanism.

Installation Location

Make sure the CDE-7859/CDE-7858/CDE-7856 will not

be installed in a location subjected to:

• Direct sun and heat

• High humidity and water

• Excessive dust

• Excessive vibrations

Handling the Detachable Front Panel

• Do not expose to rain or water.

• Do not drop or apply shock.

Correct Handling

Do not drop the disc while handling. Hold the disc so you

will not leave fingerprints on the surface. Do not affix

tape, paper, or gummed labels to the disc. Do not write on

the disc.

Disc Cleaning

Fingerprints, dust, or soil on the surface of the disc could

cause the CD player to skip. For routine cleaning, wipe

the playing surface with a clean, soft cloth from the centre

of the disc to the outer edge. If the surface is heavily

soiled, dampen a clean, soft cloth in a solution of mild

neutral detergent before cleaning the disc.

Disc Accessories

There are various accessories available on the market for

protecting the disc surface and improving sound quality.

However, most of them will influence the thickness and/or

diameter of the disc. Using such accessories can cause the

disc to be out of standard specifications and may create

operational problems. We recommend not using these

accessories on discs played in Alpine CD players.

CORRECT

INCORRECT CORRECT

Center

Hole

Bumps

Center

Hole

New

Disc

Outside

(Bumps)

Disc StabilizerTransparent Sheet

4-EN

Detaching the Front Panel

1 Press the POWER button for more than 3

seconds to turn off the power.

2 Press the (Release) button at lower left corner

until the front panel pops out.

3 Grasp the left side of the front panel and pull it

out.

NOTES

• The front panel may become hot in normal usage

(especially the connector terminals), this is not

malfunction.

• To protect the front panel, place it in the supplied

carrying case.

Attaching the Front Panel

1 First, insert the right side of the front panel into

the main unit. Align the 2 small holes on the front

panel with the 2 projections on the main unit.

2 Push the left side of the front panel until it locks

firmly into the main unit.

NOTE

Before attaching the front panel, make sure that there is

no dirt or dust on the connector terminals and no foreign

object between the front panel and the main unit.

Basic Operation

2

11

BAND

POWER

g DN f UP

c

Initial System Start-Up

Immediately after installing or applying power to the

unit, it should be initialized. To do this, first, remove

the detachable front panel. Behind the front panel, to

the right of the connector, there is a small hole.

Using a pencil or other pointed object, press the red

reset switch mounted behind this hole to complete

the initialization procedure.

Turning Power On and Off

1 Press the POWER button to turn on the unit.

NOTE

The unit can be turned on by pressing any other button

except the eject c button.

The volume level gradually increases to the previous

level you were listening to before the unit was turned

off. Press the POWER button for more than 3

seconds to turn off the unit.

NOTE

The very first time the power is turned on, the volume

will start from level 12, the BBE will be on in the tuner

mode*, and the LOUD function will be on**.

* CDE-7859/CDE-7858 only.

** CDE-7856 only.

MODE

LOUD(CDE-7856 only)

1

Reset switch

11

1

22

2

SETUP

(CDE-7859 only)

(CDE-7859)

5-EN

Subwoofer On and Off

(CDE-7859 only)

1 Press the SETUP button for at least 3 seconds.

2 Press the g DN or f UP button to select

the Sub-w mode.

3 Press the BAND button to select Subwoofer ON

or OFF.

4 After setting is completed, press the SETUP

button to return to normal mode.

NOTES

• Initial mode is "Subwoofer ON."

• Set to "Subwoofer OFF" unless the subwoofer is used.

• When the subwoofer is turned on, the subwoofer

output level can be adjusted. For more details, refer to

the Adjusting Volume/Balance/Fader.

Subwoofer On and Off (CDE-7858/

CDE-7856 only)

1 Press and hold the c(Eject) button for at least 3

seconds.

With each press, subwoofer is toggled On or Off.

NOTES

• Initial mode is "Subwoofer OFF."

• Set to "Subwoofer OFF" unless the subwoofer is used.

• When the subwoofer is turned on, the subwoofer

output level can be adjusted. For more details, refer to

the Adjusting Volume/Bass/Treble/Balance/Fader.

→ VOL → BAS →TRE

FAD ← BAL ←

Adjusting Volume/Bass/Treble/

Balance (Between Left and Right)/

Fader (Between Front and Rear)

1 Press the MODE button repeatedly to choose

the desired mode.

Each press changes the modes as follows:

(CDE-7859)

(CDE-7858/CDE-7856)

NOTES

• If the 5 or 6 button is not pressed within 5 seconds

after selecting the BASS, TREBLE, BALANCE, or

FADER mode, the unit automatically returns to the

VOLUME mode.

• When the subwoofer is set to ON, the level of the

subwoofer can be adjusted.

2 Press the

55

5 and

66

6 buttons until the desired

sound is obtained in each mode.

NOTE

The settings of the Bass and Treble will be individually

memorized for each source (FM, AM and CD) until the

setting is changed. Depending on the connected devices,

some functions and display indications do not work.

Turning Loudness On/Off

(CDE-7856 only)

Loudness introduces a special low- and high-

frequency emphasis at low listening levels. This

compensates for the ear's decreased sensitivity to

bass and treble sound.

1 Press and hold the LOUD button for at least

2 seconds to activate or deactivate the loudness

mode.

The display shows "LOUD" when the loudness

mode is activated.

→ VOL → BAL →FAD

6-EN

Basic Operation

MUTE

(CDE-7859 only)

g DN f UP

SETUP

(CDE-7859 only)

MUTE

(CDE-7858/CDE-

7856 only)

BBE (CDE-7859/CDE-7858 only)

(CDE-7859)

Audio Mute Function

Activating this function will instantly lower the

volume level by 20 dB.

1 Press the MUTE button to activate the MUTE

mode. The audio level will decrease by about

20 dB.

Pressing the MUTE button again will bring the

audio back to its previous level.

BBE Mode On/Off

(CDE-7859/CDE-7858 only)

The BBE (Barcus Berry Electronics) processor

installed in this unit is designed to correct the

phase distortion inherent in most loudspeaker

designs. Ensuring the phase integrity of the signal

driving the speakers improves the accurate

reproduction of the sound.

1 Press and hold the BBE button for at least 2

seconds to turn on the BBE mode.

Each press toggles between the BBE on and off

modes.

CLK

DISP

(CDE-7858/

CDE-7856 only)

ZERO

HOUR

MIN

BAND

7-EN

Displaying Time

1 Press the CLK (CDE-7859 only) or DISP (CDE-

7858/CDE-7856 only) button repeatedly until the

clock time is displayed.

Each press changes the modes as follows:

Radio mode

NOTE

Selecting any tuner or CD function while in the clock

priority mode will interrupt the time display

momentarily. The function selected will be displayed for

about 5 seconds before the time returns to the display.

Changing Audio Level Display

Pattern (CDE-7859 only)

1 Press the SETUP button for at least 3 seconds.

2 Press g DN or f UP button to select the

DISP mode.

3 Press BAND button to switch the display pattern.

DISP1:

Lights the Volume indicator and Audio Level

indicator.

DISP2:

Lights the mode and value bars to show the

settings in the Bass engine display.

NOTE

The last mode set will remain in effect. The mode and

value bars light and show the Bass engine settings.

DISP OFF:

Turns off the light in Bass engine display.

If you set DISP OFF, the Volume indicator, Audio

Level indicator, and Bass engine displays are

not lit at all times.

To light them, press the BAND button to exit

DISP OFF.

NOTE

If no buttons are pressed within 5 seconds, the display

will return to normal mode automatically.

4 Press the SETUP button to return to normal

mode.

Audio Level indicator

Volume indicator

Example settings:

Bass center frequency:

100 Hz

Bass band width: WIDE1

Bass level: - 6

→ DISP1 → DISP2 → DISP OFF

Setting Time

1 While the clock time is displayed, press and hold

the CLK (clock) button for at least 3 seconds.

The time indication will begin to blink.

2 Press the ZERO button while the time indication

is blinking to set seconds to "0".

3 Press the HOUR button to adjust the hours while

the time indication is blinking.

4 Press the MIN button to adjust the minutes while

the time indication is blinking.

The time indication will stop blinking 5 seconds

after the last adjustment. The time will

automatically be set.

CDE-7859: CD Player mode

DISC TEXT

mode

TRACK

TEXT mode

←

Playing time

mode

Clock priority

mode

→→→

Radio frequency

↔

Clock priority

mode

CDE-7858/CDE-7856: CD Player mode

→

Track No.

mode

→

Playing time

mode

→

Clock priority

mode

8-EN

Basic Operation

(CDE-7859)

Setting the Bass Control

(CDE-7859 only)

1 Press the BASS C. button to turn on the Bass

setting mode.

2-1

Setting the Bass frequency:

Press the g DN or f UP button to select

the desired Bass center frequency.

Emphasizes the displayed Bass frequency

ranges.

2-2

Setting the Bass Band Width (Q-Factor):

Press the BAND button to select the desired

Bass Band Width.

Changes the displayed frequency's band width to

narrow or wide.

2-3

Setting the Bass Level:

Press the

55

5 or

66

6

button to select the desired Bass

Level (-7~+7).

You can emphasize or weaken the bass

frequency.

NOTE

If no buttons are pressed within 5 seconds, the Bass

control setting will be turned off automatically.

You can change the Bass Frequency emphasis to

create your own tonal preference.

60Hz ↔ 80Hz ↔ 100Hz ↔ 200Hz

Setting the Treble Control

(CDE-7859 only)

1 Press the TREBLE C. button to turn on the Treble

setting mode.

2-1

Setting Treble frequency:

Press g DN or f UP button to select the

desired Treble center frequency.

10kHz ↔ 12.5kHz ↔ 15kHz ↔ 17.5kHz

Emphasizes the displayed Treble frequency

ranges.

2-2

Setting Treble Level:

Press the

55

5 or

66

6

button to select the desired

Treble Level (-7~+7).

You can emphasize the treble frequency.

NOTE

If no buttons are pressed within 5 seconds, the Treble

control setting will be turned off automatically.

Setting Bass Frequency

(CDE-7858/CDE-7856 only)

The bass control center frequency can be set at

60, 80, 100 or 200 Hz.

1 Press and hold the BASS C. button for at least 3

seconds to turn on the bass control settings.

2 Press the g DN or the f UP button to

select the desired Bass center frequency.

Each press changes the center frequency as

follows: 60 Hz, 80 Hz, 100 Hz and 200 Hz.

NOTE

If no buttons are pressed within 5 seconds, the bass

control settings will be turned off automatically.

3 Press the BASS C. button for more than 3

seconds to turn off the bass control settings.

You can change the Treble Frequency emphasis

to create your own tonal preference.

→ WIDE1 → WIDE2→ WIDE3 → WIDE4

(Wide)←→(Narrow)

...........................

11

1

22

2

TREBLE C.

(CDE-7859 only)

g DN

f UP

BASS C.

BAND

9-EN

Radio Operation

SOURCE TUNE BAND

g DN f UP

Manual Tuning

1 Press the SOURCE button until a radio

frequency appears in the display.

2 Press the BAND button repeatedly until the

desired radio band is displayed.

Each press changes the band:

→ F1(FM1) → F2(FM2) → AM

3 Press the TUNE button repeatedly until "DX

SEEK" and "SEEK" disappear from the display.

NOTE

The initial mode is DX SEEK.

4 Press the g DN or f UP button to move

downward or upward one step respectively until

the desired station frequency is displayed.

NOTE

The ST indicator appears on the display when a Stereo

FM station is tuned in.

Automatic Seek Tuning

1 Press the SOURCE button until a radio

frequency appears in the display.

2 Press the BAND button repeatedly until the

desired radio band is displayed.

Each press changes the band:

→ F1(FM1) → F2(FM2) → AM

3 Press the TUNE button to illuminate the DX and

SEEK indicators in the display.

With the DX (Distance) mode activated, both

strong and weak stations will be tuned in the

Auto-Seek operation.

Press again to return to the local mode. The DX

indicator will turn off and the SEEK indicator will

remain illuminated. Now, only strong stations will

be tuned.

4 Press the g DN or f UP button to

automatically seek for a station downward or

upward respectively.

The unit will stop at the next station it finds.

Press the same button again to seek the next

station.

(CDE-7859)

10-EN

Manual Storing of Station Presets

1 Select the radio band and tune in a desired radio

station you wish to store in the preset memory.

2 Press and hold any one of the Preset buttons (1

through 6) for at least 2 seconds until the station

frequency on the display blinks.

3 Press the Preset button into which you wish to

store the station while the frequency display is

blinking (within 5 seconds).

The display stops blinking once the station has

been memorized. The display shows the band,

preset No. with a triangle (9) and station

frequency memorized.

4 Repeat the procedure to store up to 5 other

stations onto the same band.

To use this procedure for other bands, simply

select the band desired and repeat the

procedure.

A total of 24 stations can be stored in the preset

memory (6 stations for each band; FM1, FM2,

AM and D.A.P.).

NOTE

If you store a station in a preset memory which already

has a station, the current station will be cleared and

replaced with the new station.

Automatic Memory of Station

Presets

1 Press the SOURCE button to select the radio

mode.

2 Press the BAND button repeatedly until the

desired radio band is displayed.

3 Press and hold the A. ME button for at least 2

seconds.

The frequency on the display continues to

change while the automatic memory is in

progress. The tuner will automatically seek and

store 6 strong stations in the selected band. They

will be stored into presets 1 to 6 buttons in order

of signal strength.

When the automatic memory has been

completed, the tuner goes to the station stored in

the preset location No. 1.

NOTE

If no stations are stored, the tuner will return to the

original station you were listening to before the auto

memory procedure began.

Radio Operation

SOURCE A.ME BAND/D.A.P.

Preset button (1 through 6)

(CDE-7859)

11-EN

Storing into Direct Access Preset

(D.A.P.) Band

A combination of radio stations in any band (up to

6 stations) can be manually preset into the D.A.P.

band.

1 Press and hold the D.A.P. button for more than 2

seconds until the D.A.P. indicator appears.

Press the BAND button to select FM or AM.

The selected band will be displayed.

To memorize stations onto the D.A.P. band,

follow the steps for the Automatic or Manual

Storing of Station Presets section above.

NOTE

This function can be used together with the Automatic

Memory Preset.

To cancel the D.A.P. mode, press and hold the

D.A.P. button for more than 2 seconds. The D.A.P.

indicator will turn off.

Tuning to Preset Stations

1 Press the SOURCE button to select the radio

mode.

2 Press the BAND button repeatedly until the

desired band is displayed.

To select the D.A.P. band, press and hold the

D.A.P. button for more than 2 seconds until the

D.A.P. indicator appears in the display.

3 Press the station Preset button that has your

desired radio station in memory.

The display shows the band, preset number with

a triangle and frequency of the station selected.

12-EN

The display shows the track number and elapsed

time of the track being played (Only the track

number is displayed on CDE-7858/CDE-7856).

When the last track is played back the player

returns to the first track and begins playback

from that point.

If a CD is already loaded in the CD player, press

the SOURCE button to select the CD mode.

2 Press the -/J button to temporarily stop CD

playback.

To resume playback, press the -/J button

again.

Music Sensor (Skip)

1 Momentarily press the g DN button once

during CD play to return to the beginning of the

current track. If you wish to access the beginning

of a track further back, repeatedly press until you

reach the desired track.

Press the f UP button once to advance to the

beginning of the next track. If you wish to access

the beginning of a track further ahead, press

repeatedly until the desired track is reached.

NOTE

The music sensor feature is functional in the play or

pause mode.

Fast Forward and Backward

1 Press and hold the g DN or f UP button to

quickly move backward or forward until you

reach the desired section of the track.

CD Player Operation

- / J

TITLE

(CDE-7859 only)

M.I.X.

f UP

g DN

SCAN

c

REPEAT

Inserting/Ejecting Disc

1 Insert a CD half way into the slot with the label

side facing up. The player automatically draws

the disc into the disc compartment.

The Disc indicator appears to show that a disc is

loaded.

NOTE

Three-inch (8cm) CD's can be used.

2 Press the c(Eject) button when you want to

eject the CD.

NOTES

• If the CD is not removed for several seconds after it

has been ejected, the player automatically draws the

CD into the compartment to protect the CD.

• Only compact discs showing the marks below can be

used. For models CDE-7858/CDE-7856, text

information is not displayed.

• We cannot fully guarantee the playback of CD-R (CD-

Recordable). You cannot playback CD-RW (CD-

ReWritable) on this unit.

Normal Play and Pause

1 Insert a CD. The CD player begins playback from

the first track on the disc.

(CDE-7859)

13-EN

Displaying and Scrolling CD Text

(CDE-7859 only)

While playing the audio CD with CD Text, the disc

and track names can be displayed and scrolled.

1 In CD mode, press the TITLE button repeatedly

to display Disc Text or Track Text.

NOTE

If your CD has no Text Information, NO TEXT appears.

2 Press and hold the TITLE button for at least 3

seconds to scroll the information stored on the

disc.

After scrolling, the display returns to normal

mode.

NOTE

SCROLL: the display is scrolled only when a disc is

loaded or when a track is changed, and when the power

turns ON during CD mode on this unit.

Repeat Play

1 Press the REPEAT button to play back

repeatedly the track being played.

The RPT indicator appears and the track will be

played repeatedly.

Press the REPEAT button again and select OFF

to deactivate the repeat play.

M.I.X. (Random Play)

1 Press the M.I.X. button in the play or pause

mode.

The M.I.X. indicator will illuminate and the tracks

on the disc will be played back in a random

sequence. After all the tracks on the disc have

been played back once, the player will begin a

new random sequence play until the M.I.X. mode

is cancelled.

To cancel M.I.X. play, press the M.I.X. button

again to turn off the M.I.X.

Scanning Programs

1 Press the SCAN button to activate the Scan

mode.

The first 10 seconds of each track will be played

back in succession.

To stop scanning, press the SCAN button and

deactivate the Scan mode.

14-EN

Information

CD

CD Player not functioning.

• Out of operating temperature range +50˚C (+120˚F) for

CD.

- Allow the vehicle's interior (or trunk) temperature to

cool.

CD playback sound is wavering.

• Moisture condensation in the CD Module.

- Allow enough time for the condensation to evaporate

(about 1 hour).

CD insertion not possible.

• A CD is already in the CD player.

- Eject the CD and remove it.

• The CD is being improperly inserted.

- Make sure the CD is being inserted following

instructions in the CD Player Operation section.

Unable to fast forward or backward the CD.

• The CD has been damaged.

- Eject the CD and discard it; using a damaged CD in

your unit can cause damage to the mechanism.

CD playback sound skips due to vibration.

• Improper mounting of the unit.

- Securely re-mount the unit.

• Disc is very dirty.

- Clean the disc.

• Disc has scratches.

- Change the disc.

• The pick-up lens is dirty.

- Do not use a commercial abailable lens cleaner disc.

Consult your nearest ALPINE dealer.

CD playback sound skips without vibration.

• Dirty or scratched disc.

- Clean the disc; damaged disc should be replaced.

Error displays (built-in CD player only)

• Mechanical error

- Press the c button. After the error indication

disappears, insert the disc again. If the above-

mentioned solution does not solve the problem,

consult your nearest ALPINE dealer.

In Case of Difficulty

If you encounter a problem, please review the items in

the following checklist. This guide will help you

isolate the problem if the unit is at fault. Otherwise,

make sure the rest of your system is properly

connected or consult your authorized Alpine dealer.

Basic

No function or display.

• Vehicle's ignition is off.

- If connected following instructions, the unit will not

operate with the vehicle's ignition off.

• Improper power lead connections.

- Check power lead connections.

• Blown fuse.

- Check the fuse on the battery lead of the unit; replace

with the proper value if necessary.

• Internal micro-computer malfunctioned due to

interference noise etc.

- Press the Reset switch with a ball-point pen or other

pointed article.

Radio

Unable to receive stations.

• No antenna or open connection in cable.

- Make sure the antenna is properly connected;

replace the antenna or cable if necessary.

Unable to tune stations in the seek mode.

• You are in a weak signal area.

- Make sure the tuner is in the DX mode.

• If the area you are in is a primary signal area, the

antenna may not be grounded and connected properly.

- Check your antenna connections; make sure the

antenna is properly grounded at its mounting location.

• The antenna may not be the proper length.

- Make sure the antenna is fully extended; if broken,

replace the antenna with a new one.

Broadcast is noisy.

• The antenna is not the proper length.

- Extend the antenna fully; replace it if it is broken.

• The antenna is poorly grounded.

- Make sure the antenna is grounded properly at its

mounting location.

15-EN

Indication for CD

• Protective circuit is activated due to high temperature.

- The indicator will disappear when the temperature

returns to within operation range.

• Mechanism error.

1. Press the c button and eject the CD.

If not ejecting, consult your Alpine dealer.

2. When the error indication remains after ejecting,

press the c button again.

If the error indication still does not turn off after

pressing the c button for a few times, consult your

Alpine dealer.

Note

When the "ERROR" or "- - - E" is displayed:

In case that the disc cannot be ejected by pressing the c

button, press the Reset switch (refer to page 4) and press

the c button again.

If not ejecting, consult your Alpine dealer.

• No indicated disc.

- Choose another disc.

Specifications

FM TUNER SECTION

Tuning Range 87.7 – 107.9 MHz

Mono Usable Sensitivity 9.3 dBf (0.8 µV/75 ohms)

50 dB Quieting Sensitivity 13.5 dBf (1.3 µV/75 ohms)

Alternate Channel Selectivity 80 dB

Signal-to-Noise Ratio 65 dB

Stereo Separation 35 dB

AM TUNER SECTION

Tuning Range 530 – 1,710 kHz

Sensitivity (IEC Standard) 22.5 µV/27 dB

CD PLAYER SECTION

Frequency Response 5 – 20,000 Hz (±1 dB)

Wow & Flutter (% WRMS) Bleow measurable limits

Total Harmonic Distortion 0.008% (at 1 kHz)

Dynamic Range 95 dB (at 1 kHz)

Signal-to-Noise Ratio 105 dB

Channel Separation 85 dB (at 1 kHz)

GENERAL

Power Requirement 14.4 V DC

(11–16 V allowable)

Maximum Power Output 45 W × 4 (CDE-7859/

CDE-7858 only)

40 W × 4 (CDE-7856 only)

Maximum Pre-Output Voltage 2 V/10 k ohms

Bass ±14 dB at 60 Hz

Treble ±14 dB at 10 kHz

Weight 1.5 kg (3 lbs. 5 oz)

CHASSIS SIZE

Width 178 mm (7")

Height 50 mm (2")

Depth 155 mm (6-1/8")

NOSEPIECE SIZE

Width 170 mm (6–3/4")

Height 46 mm (1-13/16")

Depth 20 mm (11/16")

Due to continuous product improvement, specifications and

design are subject to change without notice.

HI TEMP

(CDE-7858/CDE-7856 only)

– – – H

(CDE-7859 only)

– – – EERROR

(CDE-7859 only)

(CDE-7858/CDE-7856 only)

T – – –T– – – – –

(CDE-7859 only)

(CDE-7858/CDE-7856 only)

16-EN

Installation and Connections

Before installing or connecting the unit, please

read the following and pages 2 and 3 of this

manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire

or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE

GROUND.

(Check with your dealer if you are not sure.) Failure to do

so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM

THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due

to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED

IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual

to prevent obstructions when driving. Cables or wiring

that obstruct or hang up on places such as the steering

wheel, gear lever, brake pedals, etc. can be extremely

hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other

equipment. Doing so will exceed the current carrying capacity

of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN

DRILLING HOLES.

When drilling holes in the chassis for installation, take

precautions so as not to contact, damage or obstruct pipes,

fuel lines, tanks or electrical wiring. Failure to take such

precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR

STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or

any other safety-related system), or tanks should NEVER

be used for installations or ground connections. Using

such parts could disable control of the vehicle and cause

fire etc.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT

HINDER VEHICLE OPERATION, SUCH AS THE

STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper

movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY

EXPERTS.

The wiring and installation of this unit requires special

technical skill and experience. To ensure safety, always

contact the dealer where you purchased this product to

have the work done.

SERIAL NUMBER:

INSTALLATION DATE:

INSTALLATION TECHNICIAN:

PLACE OF PURCHASE:

IMPORTANT

Please record the serial number of your unit in the

space provided below and keep it as a permanent

record. The serial number plate is located on the

bottom of the unit.

USE SPECIFIED ACCESSORY PARTS AND INSTALL

THEM SECURELY.

Be sure to use only the specified accessory parts. Use of

other than designated parts may damage this unit

internally or may not securely install the unit in place.

This may cause parts to become loose resulting in hazards

or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR

PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like

the seat rails) or sharp or pointed edges. This will prevent

crimping and damage to the wiring. If wiring passes

through a hole in metal, use a rubber grommet to prevent

the wire’s insulation from being cut by the metal edge of

the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH

MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence

of moisture or dust. Moisture or dust that penetrates into

this unit may result in product failure.

Precautions

• Be sure to disconnect the cable from the (–) battery post

before installing your CDE-7859/CDE-7858/CDE-

7856. This will reduce any chance of damage to the unit

in case of a short-circuit.

•

Be sure to connect the color coded leads according to the

diagram. Incorrect connections may cause the unit to

malfunction or damage to the vehicle’s electrical system.

• When making connections to the vehicle’s electrical

system, be aware of the factory installed components

(e.g. on-board computer). Do not tap into these leads to

provide power for this unit. When connecting the CDE-

7859/CDE-7858/CDE-7856 to the fuse box, make sure

the fuse for the intended circuit of the CDE-7859/CDE-

7858/CDE-7856 has the appropriate amperage. Failure

to do so may result in damage to the unit and/or the

vehicle. When in doubt, consult your ALPINE dealer.

• The CDE-7859/CDE-7858/CDE-7856 uses female

RCA-type jacks for connection to other units (e.g.

amplifier) having RCA connectors. You may need an

adaptor to connect other units. If so, please contact your

authorized ALPINE dealer for assistance.

• Be sure to connect the speaker (–) leads to the speaker

(–) terminal. Never connect left and right channel

speaker cables to each other or to the vehicle body.

17-EN

Mounting Sleeve

(Included)

CDE-7859/CDE-7858/CDE-7856

No Pressure Here

Dashboard

Metal

Mounting

Strap

Chassis

Screw

Hex Nut (M5)

Bolt Stud

CDE-7859/CDE-7858/

CDE-7856

Ground Lead

∗∗

∗

Lock Pin

Slide the CDE-7859/CDE-7858/CDE-7856 into the

dashboard. When the unit is in place, make sure the

locking pins are fully seated in the down position.

This can be done by pressing firmly in on the unit

while pushing the locking pin down with a small

screwdriver. This ensures that the unit is properly

locked and will not accidentally come out from the

dashboard. Install the Detachable Front Panel.

Removal

1 Remove the DETACHABLE FRONT PANEL.

2 Use a small screwdriver (or similar tool) to push

the locking pins to the "up" position (see above

drawing). As each pin is unlocked, gently pull out

on the unit to make sure it does not re-lock before

unlocking the second pin.

3 Pull the unit out, keeping it unlocked as you do

so.

3

Face Plate

Mounting Bracket

Ground Lead

CDE-7859/CDE-7858/CDE-7856

Screws (M5 × 8)

(Included)

NOTE

Secure the ground lead of the unit to a clean metal spot

using a screw (

∗

) already attached to the vehicle's

chassis.

∗

Installation

1

Remove the Detachable Front Panel (refer to page

4). Slide mounting sleeve from main unit. (see

“Removal” on this page).

Slide the mounting sleeve into the dashboard.

NOTE

Please examine the installation. Make certain that no

external pressure is applied to either the top of the unit

or the removable nosepiece.

2

Reinforce the head unit with the metal mounting

strap (not supplied). Secure the ground lead of the

unit to a clean metal spot using a screw (

∗

) already

attached to the vehicle’s chassis.

NOTE

For the screw marked

**

, use an appropriate screw for

the chosen mounting location.

Connect each input lead coming from an amplifier or

equalizer to the corresponding output lead coming

from the left rear of the CDE-7859/CDE-7858/CDE-

7856. Connect all other leads of the CDE-7859/CDE-

7858/CDE-7856 according to details described in the

CONNECTlONS section.

18-EN

(

&

%

$

#

"

!

9

6

5

4

3

2

7

)

~

8

1

Installation and Connections

Connections

Antenna

To power antenna

To amplifier or equalizer

Ignition Key

Battery

Front right

Rear right

Speakers

Rear left

Front left

Amplifier

Rear or Subwoofers∗

∗ When Subwoofer is set to OFF: Output is from Rear speakers.

When Subwoofer is set to ON: Output is from Subwoofer.

For details on how to set the Subwoofer to ON/OFF, see “Subwoofer On and Off” on page 5.

Gray/

Black

Gray

Violet/

Black

Violet

Green

Green/

Black

White/

Black

White

SPEAKER

RIGHT

FRONT

Blue/White

Blue

Red

Yellow

Black

SPEAKER

RIGHT

REAR

SPEAKER

LEFT

REAR

SPEAKER

LEFT

FRONT

POWER ANT

REMOTE

TURN-ON

IGNITION

BATTERY

GND

19-EN

1 Antenna Receptacle

2 Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power

antenna, if applicable.

3 Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your

amplifier or signal processor.

4 Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle's

fuse box or another unused power source which

provides (+)12V only when the ignition is turned on

or in the accessory position.

5 Battery Lead (Yellow)

Connect this lead to the positive (+) post of the

vehicle's battery.

6 Ground Lead (Black)

Connect this lead to a good chassis ground on the

vehicle. Make sure the connection is made to bare

metal and is securely fastened using the sheet metal

screw provided.

7 Fuse Holder (15A)

8 Power Supply Connector

9 Right Front (+) Speaker Output Lead (Gray)

! Right Front (–) Speaker Output Lead (Gray/

Black)

" Right Rear (–) Speaker Output Lead (Violet/

Black)

# Right Rear (+) Speaker Output Lead (Violet)

$ Left Rear (+) Speaker Output Lead (Green)

% Left Rear (–) Speaker Output Lead (Green/

Black)

& Left Front (–) Speaker Output Lead (White/Black)

( Left Front (+) Speaker Output Lead (White)

) Rear/Subwoofer RCA Connectors

RED is right and WHITE is left.

~ RCA Extension Cable (Sold Separately)

To prevent external noise from entering the audio system.

• Locate the unit and route the leads at least 10 cm away from the car harness.

• Keep the battery power leads as far away from other leads as possible.

• Connect the ground lead securely to a bare metal spot (remove the coating if necessary) of the car chassis.

• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries

various Alpine noise suppressors, contact them for further information.

• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

Page is loading ...

Alpine CDE-7858 User manual

This manual is also suitable for

Alpine CDE-7858 User manual

in other languages

Related papers

Other documents