Siemens LC359KA70/01 Owner's manual

Page is loading ...

Appliance description

Operating modes

Exhaust-air mode:

❑ The extractor-hood fan extracts the

kitchen vapours and conveys them

through the grease ﬁlter into the

atmosphere.

❑ The grease ﬁlter absorbs the solid

particles in the kitchen vapours.

❑ The kitchen is kept almost free of grease

and odours.

D

When the extractor hood is operated

in exhaust-air mode simultaneously with

a different burner which also makes use

of the same chimney (such as gas, oil or

coal-ﬁred heaters, continuous-ﬂow heaters,

hot-water boilers) care must be taken to

ensure that there is an adequate supply

of fresh air which will be needed by the

burner for combustion.

Safe operation is possible provided that the

underpressure in the room where the

burner is installed does not exceed 4 Pa

(0.04 mbar).

Operating modes

This can be achieved if combustion air can

ﬂow through non-lockable openings, e.g. in

doors, windows and via the air-

intake/exhaust-air wall box or by other

technical measures, such as reciprocal

interlocking, etc.

If the air intake is inadequate, there is a

risk of poisoning from combustion gases

which are drawn back into the room.

An air-intake/exhaust-air wall box by itself is

no guarantee that the limiting value will not

be exceeded.

Note: When assessing the overall

requirement, the combined ventilation

system for the entire household must be

taken into consideration. This rule does not

apply to the use of cooking appliances,

such as hobs and ovens.

Unrestricted operation is possible if the

extractor hood is used in recirculating mode

– with activated carbon ﬁlter.

Circulating-air mode:

❑ An activated carbon ﬁlter must be ﬁtted

for this operating mode (see Filters and

maintenance).

The complete installation set and

replacement ﬁlters can be obtained from

specialist outlets.

❑ The extractor-hood fan extracts the

kitchen vapours which are puriﬁed in the

grease ﬁlter and activated carbon ﬁlter

and then conveyed back into the

kitchen.

❑ The grease ﬁlter absorbs the grease

particles in the kitchen vapours.

❑ The activated carbon ﬁlter binds the

odorous substances.

 If no activated carbon ﬁlter is installed,

it is not possible to bind the odorous

substances in the cooking vapours.

Before reading these instructions, please open out

the folded last page with the illustration.

Randabsaugungs-Segmenten

Chimney

panelling

Light /

fan switches

Filter grille

Light

Edge extraction segments

10

11

Before using for the ﬁrst time

Important notes:

❑ The Instructions for Use apply to several

versions of this appliance. Accordingly,

you may ﬁnd descriptions of individual

features that do not apply to your

speciﬁc appliance.

❑ This extractor hood complies with all

relevant safety regulations.

Repairs should be carried out by

qualiﬁed technicians only.

Improper repairs may put the user at

considerable risk.

❑ Before using your appliance for the ﬁrst

time, please read these Instructions for

Use carefully. They contain important

information concerning your personal

safety as well as on use and care of the

appliance.

❑ Please retain the operating and

installation instructions for a subsequent

owner.

Gas hobs / Gas cookers

 Do not use all the gas hotplates

simultaneously for a prolonged period

(max. 15 minutes) at maximum thermal

load, otherwise there is a risk of burns if the

housing surfaces are touched or a risk of

damage to the extractor hood. If the

extractor hood is situated over a gas hob,

operate the hood at maximum setting if

three or more gas hotplates are operated

simultaneously.

❑ This appliance is labelled

in accordance with

European Directive

2002/96/EG concerning

used electrical and

electronic appliances

(waste electrical and

electronic equipment –

WEEE). The guideline

determines the framework for the return

and recycling of used appliances as

applicable throughout the EU.

Note that one large burner of more than 5

kW (Wok) is equivalent to the power of 2

gas burners.

Never operate a gas cooking area without

a cooking utensil on it. Regulate the flame

in such a way that it does not project over

the cooking utensil.

12

Before using for the ﬁrst time

Safety instructions

Do not ﬂambé food directly under the

extractor hood.

Risk of grease ﬁlter catching ﬁre due

! to ﬂames.

 The hotplates must always be covered

with a utensil.

 Restrictions apply to the use of the

extractor hood over a solid-fuel burner

(coal, wood, etc.). (See Installation

instructions).

 Do not use the appliance if damaged.

 The appliance is not intended for use

by young children or inﬁrmed persons

without supervision.

Young children should be supervised to

ensure they do not play with the appliance.

If the connecting cable for this

appliance is damaged, the cable must be

replaced by the manufacturer or his

customer service or a similarly qualiﬁed

person in order to prevent serious injury to

the user.

 The appliance may be connected to

the mains by a qualiﬁed technician only.

 Dispose of packaging materials

properly (see Installation instructions).

 This extractor hood is designed for

domestic use only.

 Light bulbs must always be ﬁtted when

the extractor hood is in use.

 Defective bulbs should be replaced

immediately to prevent the remaining bulbs

from overloading.

 Never operate the extractor hood

without a grease ﬁlter.

 Overheated fat or oil can easily catch

ﬁre.

If you are cooking with fat or oil, e.g. chips,

etc., never leave the cooker unattended.

 Carefully clean the extractor hood

before switching on for the ﬁrst time.

 Do not place any objects on the

extractor hood.

Never allow children to play with the

appliance.

Do not let adults or children operate the

appliance unsupervised:

– if they are mentally or physically unable

to use the appliance safely and correctly,

– if they don’t have the knowledge and

experience to use the appliance safely

and correctly.



13

Operating procedure

 To activate the functions, simply tap the

buttons. If the buttons are pressed for too

long, no function is activated.

 The most effective method of removing

vapours produced during cooking is to:

❑ Switch the ventilator ON

as soon as you begin cooking.

❑ Switch the ventilator OFF

a few minutes after you have ﬁnished

cooking.

Acoustic signal:

❑ When a button is pressed, this is veriﬁed

by an acoustic signal.

Switching the fan ON

❑ Press the + button.

Setting the required fan speed:

❑ Press the + button.

The fan speed is increased by one step.

❑ Press the – button.

The fan speed is reduced by one step.

Switching the fan OFF:

❑ Press the button.

Or:

❑ Keep pressing the – button until the fan

switches off.

Intensive setting:

Maximum power is obtained at the

intensive setting. It is only required for short

intervals.

❑ Keep pressing the + button until a

ç

appears in the display.

❑ If the intensive setting is not cancelled by

hand, the fan will automatically switch

back to step

} after 10 minutes.

Fan follow-on:

❑ Press the

! button.

The fan continues to run at step

| for

10 minutes, and at the same time a dot

ﬂashes in the display. After this period

the fan switches off automatically.

Lighting:

❑ The light can be switched on at any

time, even though the fan is switched off.

Querying the selected operating mode:

The extractor hood must be connected and

switched off.

When the button – is pressed twice

(within 1 second), the

~ symbol is indicated

if the hood has been set to exhaust air

mode, the

Csymbol is indicated if the hood

has been set to circulating air mode.

14

Removing and installing the edge

extraction segments and the

metal-mesh grease ﬁlters:

Attention: The halogen bulbs must be

switched off and must have cooled down.

1. Take hold of the edge extraction

segments at the side, pull them down

and remove, Fig. 1.

2. Depress the handles on the grease ﬁlters

and fold down the grease ﬁlters, Fig. 1.

3. Clean the grease ﬁlters.

4. Re-install the cleaned grease ﬁlters.

5. Attach the edge extraction segments in

reverse sequence.

6. Clearing the

# display.

Press the button 2 x in succession.

A signal sounds and the

#

display

goes out.

Activated carbon ﬁlter:

For neutralizing odours in recirculating

mode.

Caution:

As the ﬁlter becomes more and more

saturated with grease, there is an increased

risk of ﬁre and the function of the extractor

hood may be impaired.

Important:

Change the activated carbon ﬁlter promptly

to prevent the risk of ﬁre from the

accumulation of heat when deep-fat frying

or roasting.

Saturation indicator:

b

When the activated carbon ﬁlter is

saturated,

C

ﬂashes. The activated carbon

ﬁlter should be changed now.

Filters and maintenance

Grease ﬁlters:

Metal ﬁlters are used to trap the greasy

element of the vapours that develop

during cooking.

The ﬁlter mats are made from non-

combustible metal.

Caution:

As the ﬁlter becomes more and more

saturated with grease, not only does the

risk of it catching ﬁre increase but the

efficiency of the extractor hood can also be

adversely affected.

Important:

By cleaning the metal grease ﬁlters at

appropriate intervals, the possibility of them

catching ﬁre as a result of a build-up of heat

such as occurs when deep-fat frying or

roasting is taking place, is reduced.

Saturation indicator:

~

When the grease ﬁlters are saturated, ~

ﬂashes. The grease ﬁlters should be

cleaned now.

Cleaning the metal grease ﬁlters:

❑ In normal operation (1 to 2 hours daily),

the metal grease ﬁlter must be cleaned

1 x a month.

❑ The ﬁlters can be cleaned in a dish-

washer. It is however possible that they

will become slightly discoloured.

❑ The ﬁlter must be placed loosely, and

NOT wedged, in the dishwasher.

Important:

Metal ﬁlters that are saturated with

grease should not be washed together

with other dishes etc.

❑ When cleaning the ﬁlters by hand, soak

them in hot soapy water ﬁrst of all.

Do not use aggressive, acidic or caustic

cleaners.

Then brush the ﬁlters clean, rinse them

thoroughly and leave the water to drain off.

Filters and maintenance

Installation:

Attention: The halogen bulbs must be

switched off and must have cooled down.

1. Remove the grease ﬁlters (see Removing

and installing the edge extraction

segments and the metal-mesh grease

ﬁlters).

2. Insert the activated carbon ﬁlter. Fig. 2.

3. Lift the activated carbon ﬁlter at the front

and rotate the catches through 90°.

Fig. 3.

4. Re-install the grease ﬁlters and the edge

extraction segments in reverse

sequence.

5. Clearing the

ã display.

❑ Press the button 2 x in

succession. A signal sounds and the

C display goes out.

Replacing the activated carbon ﬁlter:

❑ During normal operation (1 to 2 hours

per day) the activated carbon ﬁlters

should be replaced approximately 1 x

year.

❑ A replacement ﬁlter can be obtained

from any authorized dealer.

❑ Use original ﬁlters only.

By doing so you will obtain maximum

performance from your extractor hood.

Disposing of the old activated carbon

ﬁlter:

❑ There are no pollutants in the activated

carbon ﬁlters. They can therefore be

disposed of as part of your normal

domestic refuse.

Cleaning and care

Isolate the extractor hood by pulling out

the mains plug or switching off the fuse.

 Do not clean the extractor hood with

abrasive sponges or with cleaning agents

which contain sand, soda, acid or chlorine!

❑ Clean the extractor hood with a hot soap

solution or a mild window cleaner.

❑ Do not scrape off dried-on dirt but wipe

off with a damp cloth.

❑ When cleaning the grease ﬁlters, remove

grease deposits from accessible parts of

the housing. This prevents the risk of ﬁre

and ensures that the extractor hood

continues operating at maximum

efficiency.

❑ Note: Do not use alcohol (spirit) on

plastic surfaces, as dull marks may

appear.

Caution: Ensure that the kitchen is ade-

quately ventilated. Avoid naked ﬂames!

 Clean the operating buttons with a mild

soapy solution and a soft, damp cloth only.

Do not use stainless-steel cleaner to clean

the operating buttons.

Stainless steel surfaces:

❑ Use a mild non-abrasive stainless steel

cleaner.

❑ Clean the surface in the same direction

as it has been ground and polished.

❑ We recommend our stainless steel

cleaner no. 461731.

See enclosed service booklet for order

address.

Aluminium and plastic surfaces:

❑ Do not use dry cloths.

❑ Use a mild window cleaning agent.

❑ Do not use aggressive, acidic or caustic

cleaners.

Observe the warranty regulations in the

enclosed service booklet.

15

16

Replacing the light bulbs

1. Switch off the extractor hood and pull

out the mains plug or switch off the

electricity supply at the fuse box.

 When switched on, the halogen bulbs

become very hot. Even for some time after

the bulbs have been switched off there is

still a risk of burns.

2. Remove the bulb ring with a screwdriver

or similar tool. Fig. 4

3. Replace the halogen light bulb

(conventional halogen bulb, 12 Volt,

max. 20 Watt, G4 cap).

Caution: Refer for plug-in lampholder.

Fig. 5.

Take hold of the bulb with a clean cloth.

4. Re-insert the bulb ring.

5. Plug the appliance into the mains or

switch it on at the fuse box.

Note: If the light does not function, check

that the bulbs have been inserted correctly.

If you encounter a problem

If an

#

or

ã

appears in the display:

❑ See "Filters and maintenance" Section.

If is not possible to operate the extractor

hood:

❑ Disconnect the extractor hood from the

mains electricity supply by pulling out the

plug or switching it off at the main fuse

box.

Wait for approx. 1 minute and then

switch it on again.

If you have any questions or if a fault

occurs, please call Customer Service.

(See list of Customer Service

representatives).

When you call, please quote the following:

Setting the saturation indicator

If it becomes necessary to change the

operating mode (exhaust-air/recirculating

mode), the saturation indicator for the ﬁlters

must also be altered (see Installation

Instructions).

E-Nr. FD

Enter the relevant numbers into the box

above. The E-Nr. (product no.) and FD

(production date) are shown on the

nameplate which can be seen inside the

extractor hood after the ﬁlter frame has

been detached.

The manufacturer of the extractor

hoods accepts no liability for complaints

which can be attributed to the design

and layout of the pipework.

Page is loading ...

88

K "4 :7>?)>*3.* 548.&)&

4>3&(>*3.* >,4)34K(.

> ;=9=(>3? *:745*/80?

   ; )>.*

)>.3.* :7>?)>*E

*1*097=(>3=(- . *1*0

9743.(>3=(- ;&89*

*1*(97.(&1 &3) *1*(974

3.( *6:.52*39 F $

"& ;=9=(>3& 407*K1&

>&8&)= 80D&)4;&3.& .

7*(=01.3,: :7>?)>*E ;=8>D=(- > :L=(.&

4'4;.?>:/?(* 3& (&D=2 9*7*3.* #3..

:745*/80.*/

$ +  # $( %+* '5*

.*7;8>* :L=(.*

K "& .3897:0(/& 4'8D:,. /*89 57>*;.)>.&3.&

)1& 7AL3=(- ;*78/.

:7>?)>*3.& 4L1.;* L* >489&D= 45.8&3*

54/*)=3(>* 8>(>*,AD= )>.&D&3.& 09A7*

3.* )49=(>? $&8>*,4 :7>?)>*3.&

K "*3 40&5 /*89 >,4)3= > 4'4;.?>:/?(=2.

3472&2. '*>5.*(>*E89;&

Naprawy 24,? '=@ )4043=;&3* 9=104

57>*> ;=85*(/&1.>4;&3= 5*7843*1

 #$ ( * !( * "! !   !  5*

", %&! "( - #"( 5! ! +#

+2%& ( "  '5* & "( ! 

:(-*30. ,&>4;*  &13.0. ,&>4;*

n .* :L=;&@ ;8>=890.(- 5&13.0A;

/*)34(>*K3.* 3& 3&/;.C08>=2 4,3.: 57>*>

)D:L8>= (>&8 2&<  2.3:9 ; 57>*(.;

2=2 7&>.* .893.*/* 3.*'*>5.*(>*E89;4 45&

7>*3.& 8.C 57>*> )4903.C(.* 54;.*7>(-3.

4':)4;= 40&5: 47&> :8>04)>*E 8&2*,4

40&5: 7>= :L=(.: 40&5: 3&) 0:(-*30?

,&>4;? ; 57>=5&)0: /*)34(>*83*,4

:L=(.& 97>*(- 1:' ;.C(*/ 5&13.0A; ,&>4

;=(- 40&5 2:8. '=@ :89&;.43= 3& 3&/;.

C08>? 24( 54(-D&3.&3.& &1*ż= ;>.ąć 54)

:;&,ę ż* ):ż= 5&13.0 > 24(ą ;.ę08>ą 3.ż 

0$ $40 4)54;.&)& 24(= );A(- 5&13.0A;

,&>4;=(-

.* 3&1*ż= 3.,)= :ż=;&ć 5&13.0& ,&>4;*,4

'*> 5489&;.43=(- 3& 3.2 3&(>=ń #7*,:14

;&ć 4,.*ń ; 9&0. 8548A' &'= 3.* ;=)489&

;&ł 8.ę 54>& 4'7ę' 3&(>=3.&

K 7>*) :L=(.*2 34;*,4 :7>?)>*3.&

)40D&)3.* >&54>3&@ 8.C > .3897:0(/?

4'8D:,. %&;.*7& 43& 3.*>'C)3* .3+47

2&(/* )49=(>?(* $&8>*,4 '*>5.*(>*

E89;& & 9&0L* :L=904;&3.& . :97>=2&3.&

:7>?)>*3.&

K 3897:0(/C 4'8D:,. . 2439&L: 3&1*L=

>&(-4;&@ ; )4'7=2 89&3.* )1& *;*39:

&13*,4 041*/3*,4 ;D&K(.(.*1&

Page is loading ...

92

& $ *'& $ +* !

"! &5

Uwaga: L&7A;0.-&14,*34;*2:8>?'=@

;=D?(>43*.;=89:)>43*

1. 4(-=1.@+.197=>54(-D&3.&3.*24';4)4

;=21*004(-;=9&/?(/* =8

2. $=24394;&@+.197=)49D:8>(>A;5&97>

G$=24394;&3.*.2439&L2*9&14;=(-+.1

97A;)49D:8>(>=H

3. $574;&)>.@+.1973&;C,.*1&09=;3= =8

4. 4)3.*K@)457>4):+.1973&;C,.*1&09=;3=

.4'7A(.@>&203.C(.&4B =8

5. %&24394;&@+.197=)49D:8>(>A;5&97>

G$=24394;&3.*.2439&L2*9&14;=(-+.1

97A;)49D:8>(>=H

6. 4)3.*K@+.197=>54(-D&3.&3.*24';4)4

;=2:2.*8>(>&/?(04D0.;4)54;.*)3.(-

857CL=3&(-

7.  *1,+*-"+! + ! 

CC

.

K &(.83?@7&>=041*/34,:>.0 

4/&;.&8.C8=,3&D&0:89=(>3=&4>3&

(>*3.*

C >3.0&

 * "!& "(  !

(   L&7A;0.-&14,*34;*2:8>?'=@

;=D?(>43*.;=89:)>43*

1. 4(-=1.@+.197=>54(-D&3.&3.*24';4)4

;=21*004(-;=9&/?(/* =8

2. $=24394;&@+.197=9D:8>(>4;*

3. '7A(.@>&203.C(.&4B.;=(.?,3?@+.197

3&;C,.*1&09=;3=0.*7:/?(,40:)4D4;.

=8

4. %&24394;&@+.197=9D:8>(>4;*

5. 4)3.*K@+.197=>54(-D&3.&3.*24';4)4

;=2:2.*8>(>&/?(04D0.;4)54;.*)3.(-

857CL=3&(-

  !& $ ! ( 0  & *( ! *

K 7>=3472&13=2:L=(.:4))4,4)>.3

3&)>.*E+.197=3&;C,.*1&09=;3=54;.33=

'=@;=2.*3.&3*K7*)3.47&>3&740

K .197=3&;C,.*1&09=;3=8?)489C53*9=104

;85*(/&1.89=(>3=(-5:309&(-857>*)&L=

K   5*' 5*( -& * ""$* ! !* 

& $/( 

"=28&2=2>&5*;3.&8.C459=2&13*

+:30(/434;&3.*:7>?)>*3.&

* + '5*&  "& $  !( 0

 & *( !*

K .197=3&;C,.*1&09=;3=3.*>&;.*7&/?

>&3.*(>=8>(>&/?(=(-8:'89&3(/.4,?'=@

97&094;&3*35/&04)5&)=042:3&13*

34

Per attivare le funzioni associate ai

tasti è necessario imprimere sugli stessi

un piccolo impulso (poca forza per un

breve istante). Pressioni eccessive e

prolungate non attivano le funzioni

associate.

Interrogazione stato filtri:

Con la cappa in stand-by, premendo due

volte consecutivamente il tasto (in 1

secondo), appare il carattere se la

cappa è impostata a scarico d'aria, o il

carattere se la cappa è impostata a

ricircolo d'aria.

+*%++ !  ' &$+*  !

,-+% !""  #'( *,  ,

( & *+ 0+!+ ' &  5( *1,+ ,

+# +! 

n .*3&1*L=2=@40&5:9;&7)=2.

,?'0&2.(>=9*LK74)0&2.(>=8>(>?(=2.

>&;.*7&/?(=2.5.&8*084)C0;&8(>=(-147

K 4(>=8>(>*3.&40&5:3&1*L=:L=;&@

(.*5D*/;4)=>)4)&90.*2K74)0&

(>=8>(>?(*,4&1'4)*1.0&93*,45D=3:)4

2=(.&8>='

K .*3&1*L=:8:;&@8:(-=(->&'7:)>*E

>)7&5:/?(/*&1*>2.C0(>&/?(/*;.1

,493?8>2&90?

K 7>=2=(.:+.197A;9D:8>(>4;=(-3&1*L=

4(>=K(.@9&0L*9D:8>(>48&)>43=3&9=(-

K(.&3&(-4':)4;=)409A7=(-/*89

)489C5"=28&2=2>&54'.*,&8.C3.*'*>

5.*(>*E89;:>&5&1*3.&8.C.>&5*;3.&8.C

459=2&13*+:30(/434;&3.*:7>?)>*3.&

K %& $ + 5!   3.*:L=;&@&104-41:85.

7=9:8:3&51&89.04;=(-54;.*7>(-3.&(-

4;.*7>(-3.&24L*:1*(>2&94;.*3.:

(    7>*;.*97>=@;=89&7(>&/?(4

0:(-3.C3.*:L=;&@;413*,44,3.&

n(>=8>(>&@,:>.0.89*7:/?(*/*)=3.*

;4)?>)4)&90.*2)*1.0&93*,4K74)0&

(>=8>(>?(*,4>&5424(&;.1,493*/2.C0

0.*/8>2&90.4,:>.0A;89*7:/?(=(-3.*

3&1*L=:L=;&@K74)0A;)489&1..34<

"( $+ !+ %&  !") 

K &1*L=:L=;&@)*1.0&93*,4K74)0&

(>=8>(>?(*,4)489&1..34<3.*K(.*73*

,4

K (>=8>(>&@54;.*7>(-3.C)*1.0&93.*

541*7:/?(

K 41*(&2=3&8>K74)*0)4(>=8>(>*3.&

89&1..34<B

)7*8)480D&)&3.&>&2A;.*E>3&/):/*

8.C3&)4D?(>43*/'748>:7>*

"( $+ ! ' !"(     $"( 

! # %& "( 

K .*3&1*L=:L=;&@8:(-=(-8>2&9*0

K &1*L=:L=;&@)*1.0&93*,45D=3:)4

8>='

K .*3&1*L=:L=;&@K74)0A;0474>=/3=(-

0;&K3=(-(>=&10&1.(>3=(-

  5*%& "%"(  -%0"+ % (  

$ ! +( $&*( + 1,+"! 

!%& $ ' '& $ +*  !.

93

 . $  %# $ '

1. %>E@)?>A51'6/5*E@)?>A5*68@*;

<>)/@-'0@)<:>)?1D??'9/2'4/'2;(:+M

<>E@)?'0@)(+?6/+)?4/1

n &'6'254+M'8B<1/.'25-+45<+

?4')?4/+9/D4'-8?+<'0@'<+:1/21'3/4;:

65/).?-'9?+4/;35-@65<5*5<'A56'

8?+4/'

2. &'6535)@L8;(518D:'2;(:>365*5(

4>).L)/@-4@A6/+8L)/+F2'36> >9

3. %>3/+4/A.'25-+45<@M'8B<1D

*59:D64'<968?+*'M>?<>1E'M'8B<1'

.'25-+45<'

$3'=%:8?54+1

Uwaga: 568'<1'2'365<' >9

568?>:8?>3'4/'M'8B<1/659E;M>A9/D

)?>9:@9?3':1@

4. '45<5?'354:5<'A6/+8L)/+F2'36>

5. 5*E@)?>A4'45<5?'9/2'4/++2+1:8>)?

4+

<E@)?'0@)<:>)?1D

2;((+?6/+)?4/1

Ostrze¿enie: 0+L2/5L</+:2+4/+4/+

*?/'E'968'<*?/A)?>M'8B<1/?59:'E>

6568'<4/+?'354:5<'4+

#9?15*?+4/'

+L2/4'<>L</+:2')?;650'</'9/D



566;8+

C :

K ':8?85?*?/'EH/2:8>/;:8?>3'4/+I

8# &"'% &'&, %'&# 

% 

K *)/@A4'6/D)/+4'51'6/+4'51

3/4;:D<>)/@-'0@)<:>)?1D2;(

68?+E@)?'0@)<>E@)?4/1(+?6/+)?+F9:<'

'9:D64/+?'E@)?>A4'45<5

%68?>6'*1;+<+4:;'24>).<>0'L4/+F)?>

;9?15*?+F?<8B)/A9/D*59+8</9;12/+4:'

':8?2/9:')+4:8;39+8</95<>).

%68?>6'*1;?-E59?+4/'4'2+M>65*'A

4'9:D6;0@)+*'4+

 +#&,  % &/% / % %).% 

%8'?/+68?+E@)?+4/':>6;*?/'E'4/'5*685

<'*?'4/+65</+:8?' 8+)>81;2')0'65</+

:8?'3;9/?59:'A5*65</+*4/5

?3/+4/54+:'1M+5?4')?+4/+

4'9>)+4/',/2:8B<6':8?/49:8;1)0'

354:'M;

 8

5<>M9?@:'(+21D<>6+E4/A5*65</+*4/3/

*'4>3/"+?4'0*;0@9/D4'/*+4:>,/1')>04+0

:'(2/)?)+)?>2/65L)/@-4/D)/;18':>,/2:8'<

<+<4D:8?4/+0<4D)+51'6;

n ( &+ %* &" '3, %  '&%&)

&'&, /  #% &8 / , %* + #%

( " # $  !)'&, &&, % (&/$  )/

/%  $  / 5%  $ ( +( 

Page is loading ...

Siemens LC359KA70/01, LF 359 BA 80, LF359BA80/01 Owner's manual

Related papers

Other documents