Simer 3075SS User manual

Brand: Simer

Model: 3075SS

Category: Water pumps

Type: User manual

Installation/Operation/Parts

For further operating, installation,

or maintenance assistance:

Call 1-800-468-7867

English . . . . . . . . . . . . . . Pages 2-6

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation,

l’installation ou l’entretien,

Composer le

1 (800) 468-7867

Français . . . . . . . . . . . Pages 7-11

Instalación/Operación/Piezas

Para mayor información sobre el

funcionamiento, instalación o

mantenimiento de la bomba:

Llame al 1-800-468-7867

Español . . . . . . . . . .Paginas 12-16

OWNER’S MANUAL

Submersible Sump Pumps

NOTICE D’UTILISATION

Pompes de puisard submersible

MANUAL DEL USUARIO

Bombas sumergible

de sumidero

MOD. 2957

293 Wright St., Delavan, WI 53115

Phone: 1-800-468-7867

1-800-546-7867

Fax: 1-800-390-5351

Safety 2

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

READ AND FOLLOW

SAFETY INSTRUCTIONS!

Carefully read and follow all safety instructions in this manual

and on pump.

This is the safety alert symbol. When you see this symbol

on your pump or in this manual, look for one of the fol-

lowing signal words and be alert to the potential for personal

injury.

warns about hazards that will cause serious per-

sonal injury, death or major property damage if ignored.

warns about hazards that can cause serious per-

sonal injury, death or major property damage if ignored.

warns about hazards that will or can cause

minor personal injury or property damage if ignored.

The word NOTICE indicates special instructions which are

important but not related to hazards.

Electrically powered sump pumps normally give many years of

trouble-free service when correctly installed, maintained, and

used. However, unusual circumstances (interruption of power to

the pump, dirt/debris in the sump, flooding that exceeds the

pump’s capacity, electrical or mechanical failure in the pump,

etc.) may prevent your pump from functioning normally. To pre-

vent possible water damage due to flooding, consult your dealer

about installing a secondary sump pump, a DC backup sump

pump, and/or a high water alarm. See the “Troubleshooting

Chart” in this manual for information about common sump

pump problems and remedies. For more information, see your

dealer or call customer service at 1-800-468-7867.

1. Know the pump application, limitations, and potential

hazards.

2. Disconnect the power before servicing.

3. Release all pressure within the system before servicing any

component.

4. Drain all the water from the system before servicing.

5. Secure the discharge line before starting the pump. An unse-

cured discharge line will whip, possibly causing personal

injury and/or property damage.

6. Check hoses for weak or worn condition before each use,

making certain that all connections are secure.

7. Periodically inspect the sump, pump and system compo-

nents. Keep free of debris and foreign objects. Perform rou-

tine maintenance as required.

8. Provide a means of pressure relief for pumps whose dis-

charge line can be shut-off or obstructed.

9. Personal Safety:

a. Wear safety glasses at all times when working with

pumps.

b. Keep work area clean, uncluttered and properly lighted –

replace all unused tools and equipment.

c. Keep visitors at a safe distance from work area.

d. Make workshop child-proof – with padlocks, master

switches, and by removing starter keys.

10. When wiring an electrically driven pump, follow all electri-

cal and safety codes that apply.

11. This equipment is only for use on 115 volt and is equipped

with an approved 3-conductor cord and 3-prong, grounding-

type plug.

Hazardous voltage. Can shock, burn or

cause death. To reduce the risk of electric shock, pull the

plug before servicing. Pump is supplied with a grounding

conductor and grounding-type attachment plug. Be sure it

is connected only to a properly grounded grounding-type

receptacle.

Where a 2-prong wall receptacle is encountered, it must be

replaced with a properly grounded 3-prong receptacle

installed in accordance with codes and ordinances that apply.

This pump has not been investigated for use in swimming

pool areas.

12. A ground fault circuit interrupter is recommended for use

with any electrical appliance submerged in water. Installation

and all wiring should be performed by a qualified electrician.

13. Make certain the power source conforms to the requirements

of your equipment.

SIMER warrants to the original consumer purchaser (“Purchaser”) of its products that they are free

from defects in material or workmanship.

If within twelve (12) months from the date of the original consumer purchase any such product

shall prove to be defective, it shall be repaired or replaced at SIMER’s option, subject to the terms

and conditions set forth below. Your original receipt of purchase is required to determine warran-

ty eligibility.

Exceptions to the Twelve (12) Month Warranty

Ninety (90) Day Warranty:

If within ninety (90) days from original consumer purchase any Drill Pump or MiniVac Pump shall

prove to be defective, it shall be replaced, subject to the terms set forth below.

Two (2) Year Warranty:

If within two (2) years from original consumer purchase, any 1/3 HP Submersible Sump Pump, or

Models 2330, 2300 or A5500, shall prove to be defective, it shall be repaired or replaced at

SIMER’s option, subject to the terms and conditions set forth below.

Three (3) Year Warranty:

If within three (3) years from original consumer purchase any 4” Submersible Well Pump, 1/2 HP

Submersible Sump Pump, or Booster Pump Model 3075SS shall prove to be defective, it shall be

repaired or replaced at SIMER’s option, subject to the terms and conditions set forth below.

Five (5) Year Warranty:

If within five (5) years from original consumer purchase any Pre-Charge water system tank shall

prove to be defective, it shall be repaired or replaced at SIMER’s option, subject to the terms and

conditions set forth below.

General Terms and Conditions

Purchaser must pay all labor and shipping charges necessary to replace product covered by this

warranty. This warranty shall not apply to acts of God, nor shall it apply to products which, in the

sole judgement of SIMER, have been subject to negligence, abuse, accident, misapplication, tam-

pering, alteration; nor due to improper installation, operation, maintenance or storage; nor to other

than normal application, use or service, including but not limited to, operational failures caused

by corrosion, rust or other foreign materials in the system, or operation at pressures in excess of

recommended maximums.

Requests for service under this warranty shall be made by returning the defective product to the

Retail outlet or to SIMER as soon as possible after the discovery of any alleged defect. SIMER will

subsequently take corrective action as promptly as reasonably possible. No requests for service

under this warranty will be accepted if received more than 30 days after the term of the warranty.

This warranty sets forth SIMER’s sole obligation and purchaser’s exclusive remedy for defective

products.

SIMER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT

DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WAR-

RANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT

EXTEND BEYOND THE DURATION OF THE APPLICABLE EXPRESS WARRANTIES PROVIDED

HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or lim-

itations on how long an implied warranty lasts, so the above limitations or exclusions may not

apply to you. This warranty gives you specific legal rights and you may also have other rights

which vary from state to state.

Simer Limited Warranty

SIMER • 293 Wright Street • Delavan, WI U.S.A. 53115

Phone: 1-800-468-7867 / 1-800-546-7867 • Fax: 1-800-390-5351

EMail: [email protected] • Web: http://www.simerpumps.com

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

General Information / Installation 3

14. Protect the electrical cord from sharp objects, hot surfaces,

oils, and chemicals. Avoid kinking the cord. Replace or

repair damaged or worn cords immediately.

15. Do not touch an operating motor. Motors can operate at

high temperatures.

16. Do not handle the pump or pump motor with wet hands or

when standing on a wet or damp surface, or in water.

Risk of electric shock. Can burn or kill. If your

basement has water or moisture on floor, do not walk on the

wet area until all power has been turned off. If the shut-off box

is in the basement, call electric company or hydro authority to

shut-off the service to house, or call your local fire department

for instructions. Failure to follow this warning can result in fatal

electrical shock.

17. DO NOT splice the electrical power cord.

18. DO NOT allow the electrical cord plug to be submerged.

19. DO NOT use extension cords. They are a fire hazard and

can reduce voltage sufficiently to prevent pumping and/or

damage motor.

20. Connect or wire the pump to an individual branch circuit

with no other outlets or equipment in the circuit. Size fuses

or circuit breakers according to the specifications.

DESCRIPTION

These 3/10 HP submersible sump pumps are designed for use in

home sumps. The units are equipped with a 3-prong grounding-

type power cord. The shaded-pole motors are oil filled and

sealed for cooler running. The sleeve bearings on the motor

shafts never need lubrication. The pumps include automatic

reset thermal protection.

SPECIFICATIONS

Power supply required.............................................115V, 60 HZ

Motor duty.................................................................Continuous

Liquid Temp. Range................................32° F-120° F (0°-49° C)

Individual Branch Circuit Required ...............................15 Amps

Discharge Adapter ..................................................1-1/4” MNPT

NOTICE: For continuous operation, the water depth must be at

least 5” (13cm), to prevent the motor from overheating.

NOTICE: This unit is not designed for applications involving salt

water or brine! Use with salt water or brine will void warranty.

PERFORMANCE

INSTALLATION

1. Install pump model number 2957-01 in a sump pit with a

minimum diameter of 9" (229mm) and pump model number

2955-01 in a sump pit with a minimum diameter of 11”

(279mm). Construct the sump pit of tile, concrete, steel or

plastic. Check the local codes for approved materials.

The pump should not be installed on clay, earth or sand sur-

faces. Clean the sump pit of small stones and gravel which

could clog the pump. Keep the pump suction housing clear

of debris.

2. Install the pump in the pit so the switch operating mecha-

nism has maximum possible clearance.

3. Install an in-line check valve to prevent flow backwards

through the pump when the pump shuts off.

4. Install the discharge plumbing.

A. When using rigid pipe, use plastic pipe. Wrap the dis-

charge pipe thread with Teflon

tape. Screw the pipe

into the pump discharge port hand tight +1 – 1-1/2 turns.

NOTICE: Do not use ordinary pipe joint compound on

plastic pipe. Pipe joint compound can attack plastics.

NOTICE: Thread the discharge pipe into the pump body

carefully to avoid stripping or crossing threads.

B. If a flexible discharge hose is used, make sure the pump

is secured in the sump to prevent movement. Do not use

a flexible discharge pipe in any permanent installation.

Risk of flooding. Can cause personal

injury or property damage. Failure to secure pump may

allow pump movement, switch interference and prevent

pump from starting or stopping.

NOTICE: The discharge piping should be as short as pos-

sible to reduce pipe friction losses. Discharge pipe diam-

eter should be equal to or larger than the discharge size

of the pump. Smaller pipe diameters will restrict the

capacity of the pump and reduce performance.

C. Secure the discharge line before starting the pump.

To reduce motor noise and vibrations, a short length of

rubber hose (e.g. radiator hose) can be connected into

the discharge line near the pump using suitable clamps.

If the pump discharge line is exposed to outside sub-

freezing atmosphere, the portion of the line exposed

must be installed so any water remaining in the pipe will

drain to the outfall by gravity. Failure to do this can

cause any water trapped in the discharge line to freeze

which could result in damage to pump.

E.I. DuPont de Nemours and Company Corporation.

Individual Switch Setting

Model Motor Max. Branch Circuit Cord in inches (mm)

Number HP Load Amps Required (Amps) Length

On Off

2957-01 3/10 10.0 15 8’ 7” (178) 2” (51)

2957-03 3/10 10.0 15 8’ 7” (178) 2” (51)

MOTOR, SWITCH, & CORD SPECIFICATIONS

GPM (LPM) AT TOTAL FEET (m)

5101520

Model (1.5m) (3m) (4.6m) (6.1m)

CAPACITY GALLONS(L)/MINUTE

2957-01 29 27 21 12 25 Ft.

2957-03 (110) (102) (80) (45) (7.6m)

No flow

at height

shown

below

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Installation / Electrical / Operation 4

5. Power Supply: These pumps are designed for 115 V., 60 Hz.,

operation and require a minimum 15 amp individual branch

circuit. Both the pump and switch are supplied with 3-wire

cord sets with grounding-type plugs. The switch plug is

inserted directly into the outlet and the pump plug inserts

into the opposite end of switch plug.

Hazardous voltage. Can shock, burn or cause

death. Pump is supplied with a grounding conductor and

grounding-type attachment plug. To reduce the risk of elec-

tric shock, be certain that it is connected only to a properly

grounded, grounding type receptacle such as a grounded

water pipe or a properly grounded metallic raceway or

ground wire system. Ground terminal on pump cord plug is

provided for your protection. DO NOT REMOVE!

A ground fault circuit interrupter is recommended for use

with any electrical appliance submerged in water. For instal-

lation of such a circuit, consult a licensed electrician.

6. After the piping and the check valve (if needed) have been

installed, the unit is ready for operation

7. Check the operation by filling the sump with water and

observing pump operation through one complete cycle.

Risk of flooding. Can cause personal injury

and/or property damage. Failure to make this operational

check may lead to flooding and premature failure.

OPERATION

Risk of electric shock. Shock can burn or kill.

Do not handle a pump or pump motor with wet hands or when

standing on wet or damp surface, or in water.

1. Keep the pump inlet screen clear.

2. The shaft seal depends on water for lubrication. Do not

operate the pump unless it is submerged in water as the

seal may be damaged if the pump is allowed to run dry.

3. The motor is equipped with an automatic reset thermal pro-

tector. If the temperature in the motor should rise unduly,

the switch will cut off all of the power before any damage

can be done to the motor. When the motor has cooled suf-

ficiently, the switch will reset automatically and restart the

motor. If the protector trips repeatedly, the pump should be

removed and checked for the cause of the difficulty. Low

voltage, long extension cords, a clogged impeller, very low

head or lift, etc., could cause cycling. Refer to the

Troubleshooting Chart on Page 5 for additional information.

4. Periodically inspect the pump, system components and

sump for debris and foreign objects. Keep the sump free of

all refuse. Perform routine maintenance as required.

Risk of flooding. Flooding can cause personal

injury or property damage. This pump comes with the auto-

matic float switch mounted on the motor cover ready for oper-

ation. Do not change switch settings. Refer to the “Motor,

Switch & Cord Specifications” chart for switch settings.

MAINTENANCE

To Clean the Pump Screen:

NOTICE: Attempting to disassemble motor will void warranty.

Risk of electrical shock. Shock can burn or kill.

Always unplug the pump from the power source before servic-

ing any system component. Do not lift pump by power cord.

1. Disconnect power before servicing.

Risk of Electric shock. Shock can burn or

cause death. When servicing the system always disconnect

power cord from the electrical outlet.

2. Loosen the discharge pipe.

3. Use the pump handle to lift the pump out of the sump pit

and place the pump on a clean level surface.

4. To clean the screen, remove the three screws holding the

screen to the pump base (See Figure 1), remove and rinse

off the screen.

5. Re-install the screen and the screws.

6. Put the pump back into the sump pit.

7. Re-install the discharge pipe.

8. Check the system operation by filling the basin with water

and observing the pump’s operation through one complete

cycle.

Flood hazard. May cause personal injury or prop-

erty damage. Failure to make this operational check can lead to

improper operation, premature pump failure and flooding.

Install Switch

on Pump

Screen

screws (3)

Screen

Anti-

Airlock

Valve

Figure 1 – To clean the Screen and Anti-airlock Valve

and to attach Float Switch.

Operation / Maintenance / Troubleshooting 5

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

To Replace the Vertical Float Switch:

NOTICE: The float must be able to complete its entire cycle

without interference from any other object.

1. Mount the bracket on the switch housing with the bracket

mounting screws. See Figure 2.

2. Mount the float and the float rod stop on the rod.

3. Slide the rod up through the bracket and into the slot in the

bottom of the switch housing. Fasten the rod into the

switch housing with the pin. See Figure 2.

Make sure the pin holds the float rod in the

switch housing; otherwise the pump will not shut off.

NOTICE: Pull gently on the rod to make sure that it cannot

come out of the switch housing.

4. Mount the switch assembly on the pump with the screws

provided.

5. Run the pump through one complete cycle to verify switch

operation is correct and that nothing interferes with the

switch’s operation.

Flood hazard. May cause personal injury or prop-

erty damage. Failure to make this operational check can lead to

improper operation, premature pump failure and flooding.

AIRLOCKS:

When a pump airlocks, it runs but does not move any water.

An airlock will cause the pump to overheat and fail.

This pump has a small hole in the side of the pump housing.

See Figure 1. This is an anti-airlock valve. If you suspect an air-

lock, insert a hat pin or a pipe cleaner into the anti-airlock hole

to clean out the debris.

Troubleshooting

SYMPTOM PROBABLE CAUSE(S) CORRECTIVE ACTION

Pump won’t start or run. Blown fuse. If blown, replace with fuse of proper size.

Low line voltage. If voltage under recommended minimum, check size of wiring from

main switch on property. If OK, contact power company or hydro authority.

Defective motor. Replace pump.

Defective float switch. Replace float switch.

Float obstructed. Remove obstruction.

Pump starts and stops Backflow of water from piping. Install or replace check-valve.

too often.

Faulty float switch. Replace float switch.

Pump won’t shut off. Defective float switch. Replace float switch.

Restricted discharge Remove pump and clean pump and piping.

(obstacle in piping).

Float obstructed. Remove obstruction.

Pump operates but Low line voltage. If voltage under recommended minimum, check size of wiring from main

delivers little or no water. switch on property. If OK, contact power company or hydro authority.

Worn or plugged impeller. Replace pump.

Anti airlock vent hole is plugged. Clean out the vent hole with a hat pin or pipe cleaner.

Piggy-back

Plug

Switch

Housing

Bracket

Rod

Stop

Bracket

Mounting

Screws

Float

Be sure the pin

holds the rod

in switch

housing;

otherwise the

pump will not

shut off.

Figure 2 – Replace the Float Switch.

Repair Parts 6

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Anti-airlock

hole

Key Part

No. Description Qty. 2957-01 2957-03

1 Power Cord 1 227-264-B-TSU 227-264-B-TSU

2 Screws, Handle, Screen, Clamp 5 670-646 670-646

3Vertical Float Switch Assembly 1 Pkg 208 Pkg 208

4 Adapter 1 229-014 229-014

5 Cover, Motor Assembly 1 ** **

6 Inlet Screen 1 667-013 667-013

7 Handle 1 383-147-B 383-147-B

REPAIR PARTS LIST

** If the motor fails, replace the pump.

( ) Indicates a different quantity is required for each model number.

Page is loading ...

Simer 3075SS User manual

Brand: Simer

Model: 3075SS

Category: Water pumps

Type: User manual

Download PDF

report

in other languages

français: Simer 3075SS Manuel utilisateur
español: Simer 3075SS Manual de usuario

Simer 3075SS User manual

Simer 3075SS User manual

in other languages

Related papers

Other documents