Kogan KASTKSTM05A User guide

Brand: Kogan

Model: KASTKSTM05A

Category: Clothes steam cleaners

Type: User guide

5-IN-1 STEAM STICK

KASTKSTM05A

• Do not share the same power supply with other high-power appliances.

• Do not use in conjunction with any extension cords.

• Use the unit only as described in this guide.

• Do not immerse the unit, its power cord or any accessories in water or other liquid.

• Place the mop pad on the bottom of the mop head before use. The mop pad is used to

wipe the floor and helps protect the floor. The mop pad can be washed and reused.

• When finished cleaning, turn the steam off to prevent damage to the floor.

• Do not use any detergent or chemicals in the tank.

• When adding water, you must turn off the power switch and unplug the unit first.

• Do not place the power cord close to any hot surfaces or sources of heat.

• Do not touch the nozzle part while the unit is in use.

• Do not spray steam onto devices that contain electrical components.

• Do not allow children or anyone unfamiliar with the appliance to use the unit.

• The maximum amount of water added to the appliance is 250ml. When adding water,

pay attention to the cover buckle and avoid spills.

• Do no attempt to repair the product yourself. If you experience any fault or damage,

cease using it immediately and contact helpKogan.com for support.

• Unplug the appliance before performing any maintenance or cleaning.

SAFETY & WARNINGS

OVERVIEW

Power Cord

Water Tank Button

Main Body

Indicator Light

Button

Stream Switch

Button

Steam Adjustment

Button

Microfibre Pad

Wiper

Jet Nozzle

Copper Brush

Nylon Brush

Extension Rod

Mop Head

Water Ta n k

Jet Nozzle Installation

Align the jet nozzle with the air outlet head at

the front of the main unit, then rotate it until the

jet nozzle is firmly attached to the unit.

Nylon Brush Installation

Attach the small brush on the jet nozzle,

ensuring the brush is installed as illustrated to

the left. Otherwise, the installed brush will not

work properly.

Wiper Installation

Attach the wiper to the jet nozzle.

1. Plug the unit into a power outlet. The power indicator will flash as the unit heats up.

2. When the indicator stops flashing and turns solid (after about 20 seconds), the unit

has finished heating and you can press the steam switch button. To stop the

steam, press the switch button again.

3. Use the controls to adjust the steam strength as required.

Note: Ensure the steam is directed away from pets, plants or other electrical appliances.

OPERATION

Extension Pole Installation

Align the extension pole with the main body of the unit and then attach it by gently rotating

the extension pole into the main unit.

In the same way, the mop head can be connected to the extension pole and the extension

pole can be connected to the Jet Nozzle.

Water shortage

It is important to pay attention to the amount of water in the tank when using the steam

mop. If the water level is too low, no water will be transferred to the mop head. If the water

tank is left empty, severe damage can be caused to the unit.

WARNING:

• To avoid overheating, please unplug the unit when not in use. The

steamer will remain hot until unplugged.

• If using for a long period, ensure the steamer is stopped every 10 minutes

to allow the unit to cool down. Using for more than 10 minutes at a time

may result in overheating and damage.

Removing and Filling the Water Tank

Note: Ensure the unit is unplugged before filling the water tank.

Press the water tank button and remove the water tank.

Pull the tank cover up and remove the tank lid.

Add water to the tank.

Note: To e x t e n d t h e l i f e o f t h e u n i t , d i s t i l l e d w a t e r i s

recommended. Never add any chemicals or detergent to the

water tank.

Replace the water tank cover.

Hold the water tank button and insert the water tank into

the main unit.

Mop pad cleaning

• Clean regularly to avoid the spread of dirt and bacteria.

• When changing the mop pad, be careful not to touch the unit outlet with your hands to

avoid burns.

• To r e m o v e odour from mop pad, dissolve 2 tablespoons each of baking soda and salt

into a half a litre of water and let the mop pad stand in it for half a day. Half a cup of

vinegar can be used instead.

• The mop pad is machine washable and should only be air dried.

Note: When removing or replacing any accessories, ensure that the unit is unplugged and

no steam is being emitted. The unit needs to be cooled for 15 minutes after unplugging to

avoid burns.

Main unit

Wipe with a cloth which is dry or dampened with warm water and a touch of mild detergent.

Do not immerse the unit in water or other liquids.

Storage

Unplug the power cord, allow the unit to cool down and wipe it clean. Remove the mop,

wrap the power cord around the mop and store it in a dry, well ventilated place.

CLEANING & CARE

Rated voltage

240V

Rated power

1200W

Rated frequency

60Hz

Maximum amount of water

250ml

Continuous operation

10-25min

Issue

Solution

Unit not heating

Ensure the power switch is on and there is power from

the outlet

The unit does not emit steam

Check the water level in the water tank; add more if

needed

Unit spills water

The steam direction is not set properly; use the

controls to adjust the steam direction and strength

SPECIFICATIONS

TROUBLESHOOTING

NOTES

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com

Kogan KASTKSTM05A User guide

Brand: Kogan

Model: KASTKSTM05A

Category: Clothes steam cleaners

Type: User guide

Download PDF

report

Kogan KASTKSTM05A User guide

Kogan KASTKSTM05A User guide

Related papers

Other documents