QRSDTLY30220VOHIEV4

VEVOR QRSDTLY30220VOHIEV4, DT4 User manual

  • Hello! I've reviewed the user manual for the VEVOR DT4 electric ceramic oven. This oven has some interesting features like its silent operation, independent heating zones, and timed shutdown. I'm ready to answer any questions you have about its use, setup, or safety precautions.
  • How do I turn on the device?
    How do I lock the device?
    What does the 'H' warning indicate?
Model: DT4
Description: the generator is silent and fan free. It adopts high-power relay
motherboard without heating output. When the heating temperature reaches
the upper limit of the set value of the program, the electric pottery plate stops
working, and starts working when it is lower than the lower limit, so as to ensure
the constant temperature of the furnace surface is set at the set temperature,
and the energy saving efficiency is high.
MENU
ON/OFF
UP
DOWN
LOCKTIMER
1. Power on: when connected to the power supply, there will be a sound drop,
and all the displays will shine at the same time.
2. On/off button: press the button for 0.5 seconds to enter the standby mode.
The power indicator is on, and the four furnace areas are displayed.
(When there is no operation in the standby state for 10 seconds, the four
furnace areas will no longer be displayed. When there is no operation in 2 minutes,
it will automatically exit the standby state and return to the shutdown state.
Standby state is as shown below:
3. Heating: For example, if you want to heat the lower left furnace area, press it in
the standby state, there will be a sound and the digital display is 0, indicating that
the furnace area has been selected successfully, and then adjust the desired
firepower gear according to the number of the sliding area below. Heating is
completed, this furnace area is double-ring heating The default mode is the inner
ring. When the mode is on or this furnace area is selected, press the middle
single/double ring switch button and the indicator light on the side will turn on,
indicating that the heating of the two rings has been turned on at the same time.
(Single/double ring heating mode can be switched according to the above method)
34
3.1. Left upper furnace Ø165 heating area: single ring heating,
power 240V/1000W □ / 1600W
3.2. Lower left furnace Ø230 heating zone: double ring heating,
power 240V/2200W □ / 2000W
3.3. Right upper furnace Ø270*165 special-shaped plate heating area:
double ring heating, power 240V/2200W□ / 2000W
3.4. Right lower furnace Ø165 heating area: single ring heating,
power 240V/1000W □ / 1600W
4. Fire control: select the furnace area, slide or click the number below, it can be
adjusted from 1 to 9 sections. Press 0 to stop heating of selected burner.
5. Lock: Long press the button for 2 seconds to lock or unlock with one sound,
and the indicator light of the child lock will light up and display LO. The child lock
can be operated under shutdown or standby state and heating state. When locking,
it is not allowed to select the furnace area and adjust the fire timing, but you can
press the on/off button.
The successful locking is shown in the figure below:
6. Timing: This function is to set the shutdown time. In the heating mode, select the
furnace area and then press the timing button to enter the timing preset, and the
corresponding timing indicator light will prompt. Then adjust the sliding area to set
the shutdown time, you can also press the number directly, such as: first press the
number 3 and then press the number 8 is 38 minutes. Multiple furnace areas can be
set for different shutdown times at the same time.
When shown in the figure, the upper left furnace area:
7. Panel high temperature warning: there is residual temperature on the rear
furnace panel, and the warning shows H. Be careful of scalding your hands.
8. Product size and precautions:
8.1. The product size is 770*520*78mm(30.3*20.47*3.07 inches). The thickness
of the product is 55mm(2.16 inches) if the foot is not included.
8.2. Open roar size 757*500*150mm (29.8*19.68*5.9 inches)
Note: if the product is used on the table, because the bottom of the use process
will produce temperature, please use high temperature resistant flame retardant
material for the table such as marble....... And so on.
56
9. Code:
E1------- to control the temperature sensor on the lampboard is open
E2------- control the short circuit of the temperature sensor on the lampboard
or the temperature around the lampboard is too high
E4------- furnace temperature sensor temperature does not change within 3 minutes.
Connecting wire/tray terminal is loose.
H-------- Warning of residual temperature on panel (there is explanation
in Article 7 of normal reminder)
H-------- thermocouple open circuit (standby and shutdown state will always flash
and the corresponding furnace area is not heated)Lo------- Locked state (article
5 is explained)
10. Simple faults and troubleshooting: the furnace head is always
heated at any gear, and the relay does not jump (thermocouple short circuit or
motherboard fault)
1515
78
910
POWER SUPPLY INSTALLATION DRAWING
Electrical diagram of the beautiful line (black, white, green E)
This figure is only for three-phase power in the United States, and the voltage
between two live lines is 240VAC
Three core cable machine connection drawing
2 4 0 V 4 0 A
L 1 L 2
E
L2L 1
The leakage switch
Earth wire
Leakage switch of power supply box
L 1 L 2
220-2 4 0 V A C
Electric ceramic oven power cord
black white green
black white green
2 2 0 V 4 0 A
LN
E
NL
The leakage switch
Earth wire
Leakage switch of power supply box
LN
2 2 0 V A C
Electric ceramic oven power cord
black white green
black white green
Electrical diagram of the beautiful line (black, white, green E)
This chart is only applicable to 220 V single-phase power countries in
Europe and China
Three core cable machine connection drawing
Earth wire Earth wire
/