2. WilTec
  3. 51704
51704

WilTec 51704 User manual

  • Hello, I have reviewed the user manual for the WilTec Scarifier 51704. This document includes the assembly steps for the device, a parts list, and an exploded view diagram. I'm ready to answer your questions about its assembly and features.
  • How do I attach the spring tine?
    What parts are used to connect the adjusting rod to the frame?
    What should I do if I have a suggestion for improvement or find a mistake?
Operation Manual
Scarifier
51704
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
The information contained in this document may alter at any time without previous notice. It is prohib-
ited to copy or spread any parts of this document in any way without prior written allowance. All rights
reserved.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously
or placing your order via the webshop.
E-mail: [email protected]
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15
To return orders for exchange, repair or for other purposes, please use the following address. Atten -
tion! To allow for a smooth execution of your complaint or return, it is important to contact our cus -
tomer service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [email protected]
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15
© by WilTec Wildanger Technik GmbH Item 51704 Page 2
http://www.WilTec.de
http://www.aoyue.eu 01 2021-1
http://www.teichtip.de
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instructions
carefully and make sure you have understood its content.
Keep these operation instructions safe.
Montage
1. Attach the spring tine (17) to the frame (8) by using the round head bolt M8×20 (16), the
hexagonal nut M8 (6) and the lock washer Ø8 (7), then tighten.
2. Attach the lift handle (1) to the frame (8) by using the hexagonal bolt M5×30 (5) and the
hexagonal nut M5 (15), then tighten.
3. Attach the adjusting rod (4) to the frame (8) by using the hexagonal bolt M8×25 (3), the
hexagonal nut M8 (6) and the lock washer Ø8 (7), then tighten.
4. Attach the adjusting frame (14) to the frame (8) by using a pin (9) and a hair cotter pin Ø3
(10).
5. Insert the plastic cap (18) to the adjusting frame (14).
6. Attach the connector (11) to the bracket (12) by using the hexagonal bolt M8×45 (13), the
hexagonal nut M8 (6) and the lock washer Ø8 (7), then tighten.
7. Attach the connector (11) to the bracket (12) by using a pin (9) and a hair cotter pin Ø3
(10).
8. Connect the adjusting steel block (2) with the adjusting rod (4), adjust them for working
depth.
9. The hexagonal bolt M8×25 (3), the hexagonal nut M8 (6) and the lock washer Ø8 (7) will
serve to connect the rake.
Parts list
№ Name Qty. № Name Qty.
1Lift handle 1 10 Hair cotter pin Ø3 2
2Adjusting steel block 1 11 Connector 1
3Hex bolt M8×25 6 12 Bracket 1
4Adjusting rod 1 13 Hex bolt M8×45 2
5Hex bolt M5×30 1 14 Adjusting frame 1
6Hex nut M8 22 15 Hex nut M5 1
7Lock washer Ø8 22 16 Round head bolt M8×20 15
8Frame 1 17 Spring tine 15
9Pin 2 18 Plastic cap 1
© by WilTec Wildanger Technik GmbH Item 51704 Page 3
http://www.WilTec.de
http://www.aoyue.eu 01 2021-1
http://www.teichtip.de
Explosion view
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions
manual require the written permission of WilTec Wildanger Technik GmbH.
© by WilTec Wildanger Technik GmbH Item 51704 Page 4
http://www.WilTec.de
http://www.aoyue.eu 01 2021-1
http://www.teichtip.de
/