Fortress Technologies FSAV10M16 User manual

Brand: Fortress Technologies

Model: FSAV10M16

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

* Before operating or installing the appliance, please read this manual and all the

safety instructions thoroughly and retain it for future reference.

Model: FSAV10M16 FSAV13M16 FSAV19M16

CONTENTS

SAFETY INSTRUCTION ..................................................................2

PARTS DESCRIPTION ...................................................................4

OPERATION INSTRUCTION ..........................................................6

MAINTENANCE INSTRUCTION .......................................................9

TROUBLESHOOTING .....................................................................11

SPECIFICATIONS .............................................................................13

WARRANTY ..................................................................................... 14

You can find many helpful information on how to use and maintain the air conditioner

properly. Just a little preventive care on the parts can extend the life of the air conditioner.

Read the troubleshooting tips before call the service centre. Many common problems can

be solved by the chart of troubleshooting tips.

Contact the authorised service technician for repair or maintenance of this unit.

Contact the authorised service technician for installation of this unit.

The air conditioner is not intended for use by person (including children) with reduced physical,

sensory or mental capabilities or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of appliance by a person responsible for their

safety.

Children should be supervised to ensure that they do not play with the air conditioner.

If the power cord is damaged, it must be replaced by the manufacturer, the authorised service

technician or a qualified person in order to avoid hazards.

Make sure the unit power and the circuit breaker are turned off before cleaning and maintenance.

CAUTION

Read This User Manual

PLEASE CONTACT AN INSTALLATION SPECIALIST FOR INSTALLATION

BEFORE OPERATION.

SAFETY INSTRUCTION

Please follow below instructions to prevent injury and property damage.

Meanings of symbols in this user manual.

WARNING

Always do this.

Never do this.

Do not change the power

cord length or share the

outlet with other appliances.

Ensure earthed effectively.

Disconnect the main power

if strange sounds, smell or

smoke comes from the unit.

Close the door while the

air conditioner is running.

Ventilate room before operating air

conditioner if there is a gas leakage from

another appliance.

It may cause electric shock or

fire due to heat generation.

Incorrect earthing may cause

electric shock.

It may cause fire or electric

shock.

It may affect the cooling or

heating effectiveness.

It may cause explosion, fire or burns.

It may cause electric shock.

It may cause failure of machine

or electric shock.

It may cause fire or electric

shock.

It may cause electric shock or fire.

If the power cord is damaged, it

must be replaced by the manufac-

turer or an authorised service

centre or a qualified person in order

to avoid a hazard.

This could damage your health.

Incorrect installation may cause

fire or electric shock.

It may cause electric shock.

It may cause an explosion or fire.

It may cause failure or electric shock.

Do not operate with wet

hands.

Do not allow water to run

into electric parts.

Do not put the power cord

close to any heating sources.

Do not operate or stop the unit by

switching on or off the power.

Do not damage or use an

unspecified power cord.

Do not direct airflow at

room occupants .

Always install circuit

breaker and a dedicated

power circuit.

Do not open the unit

during operation.

Do not put the power cord near

flammable gas or combustibles, such

as gasoline, benzene, thinner, etc.

Do not disassemble or modify the unit.

It may cause death or serious injury

Do not disassemble or modify the unit.

Ventilate room before operating air

conditioner if there is a gas leakage from

another appliance.

Ventilate room before operating air

conditioner if there is a gas leakage from

another appliance.

Connect with the power properly.

It may cause electric shock or fire.

CAUTION

When remove the air filter,

do not touch the metal parts

of the unit.

It may cause an injury.

Do not clean the unit when

power on as it may cause

fire , electric shock or injury.

Windows opened may cause

wetting of indoor and soaking

of household furniture.

Switch off the main power

and the circuit breaker before

cleaning and maintenance.

Stop operation and close

the window in storm or

hurricane.

Be careful when unpacking and

installing. Sharp edges could cause injury.

Do not clean the air

conditioner inner with water.

The insulation will be degraded

if water enter the unit . It may

cause an electric shock.

This could injure the pet or

the plant.

Do not put a pet or

plant to direct air flow.

Ventilate the room well when

used together with a stove,

etc.

An oxygen shortage may occur.

It may cause deterioration of

quality.

It may cause failure of product

or fire.

Do not use this air conditioner to

preserve precision devices, food,

pets, plants, and art objects.

Turn off the main power

when not using the

unit for a prolonged period.

If water enters the unit, turn the unit off and switch

off the circuit breaker. Isolate supply by taking the

power-plug out and contact a qualified service

technician.

It may cause failure of

appliance or accident.

Appearance may be

deteriorated due to change

of product color or

scratching of its surface.

Do not put anything

around air-inlets or inside

the air-outlet.

Do not use strong deter-

gent such as thinner but

use a soft cloth.

If bracket is damaged, it may

cause damage due to falling

of unit.

It may cause fire or electric

shock.

Ensure the installation bracket of

the outdoor appliance is not damaged

due to prolonged exposure.

Do not put anything on the

power cord and ensure that the

power cord is not compressed.

Operation without filter may

cause failure.

It contains contaminants and

could make you sick.

Ensure the air filter is inserted

securely. Recommended clean

the filter once every two weeks.

Do not drink water drained

from air conditioner.

It may cause injury or damage to property

8. Connection pipe

9. Connection cable

10. Pressure valve

Outdoor unit

1. Front panel

2. Air inlet

3. Air filter

4. Air outlet

5. Horizontal louver

6. Vertical louver

7. Display panel

Indoor unit

RUN indicator

The indicator will illuminate when the air

conditioner is in operation.

TIMER indicator

The indicator will illuminate when TIMER

setting is ON.

DEFROST i

ndicator

The indicator will illuminate when the air

conditioner starts defrosting automatically

or when the warm air control feature is

activated in heat mode.

Digital display

The temperature settings will be displayed

when the air conditioner is in operation.

Displays the error signal.

PARTS DESCRIPTION

Indicator

NOTE:

All the pictures in this manual are for

explanation purposes only. Your air conditioner

may be slightly different. The actual shape shall

be prevailed.

Defrost

Run Timer

Special functions

Vertical swing function

After the appliance starts up, users can control the vertical louver swing by the remote control.

Refrigerant Leakage Detection

The digital display will appear EC when the outdoor unit detects refrigerant leakage.

SELF CLEAN (Anti-mildew function)

When turning off the unit on COOL, DRY mode, the air conditioner will continue operating for

about 7-10 minutes at LOW fan speed. If turning off the unit on HEAT mode, it will continue

operating for about 30 seconds at LOW fan speed. This will help to dry up the condensed

water inside the evaporator, and prevent the breeding of mildew.

Under Anti-mildew operation, do not restart the air conditioner until the unit is completely off.

NOTE: This manual does not include Remote Control Operations, see the

<<REMOTE CONTROL USER MANUAL>> packed with the unit for details.

Follow Me function (Second temperature sensor)

Air conditioner is usually provided one sensor for temperature automation. This product is

specially provided extra sensor on the remote control for appropriate temperature usage for

the users.

OPERATION INSTRUCTIONS

Manual control button

Suspension bars

Manual control button

AUTO/COOL

Manual operation

Operating temperature

Manual switch

Mode

Temperature

Room temperature

Outdoor temperature

1. Optimum performance will be achieved within these operating temperatures.If the air

conditioner is used out of the above conditions, certain safety protection features

may come into operation and cause the unit to function abnormally.

2. If the air conditioner runs for a long time in cooling mode and the humidity is high,

condensed water may drip out of the unit. Please sets the vertical louver to its

maximum angle (vertically to the floor), and set HIGH fan mode.

NOTE:

COOL

HEAT DRY

0 50

-15 30 0 50

Open and lift the front panel up to an angle

until it remains fixed with a clicking sound.

Press the manual control button once will

lead to AUTO operation. If press the button

twice within five seconds, the unit will be

operated under COOL mode. To turn off the

unit, press the button continuously.

Close the panel firmly to its original

position.

It can only be used when the remote control

is disable or maintenance necessary.

Once remote control resume operation, use

the remote control directly.

CAUTION:

The unit must be turned off before operating

by the manual control button.

HEAT mode cannot be activated by the manual

control button.

17 C~32 C

0 C~30 C

10 C~32 C

Manual operation can be used temporarily in case the remote control is disable or

maintenance necessary.

Air flow direction control

Adjust the air flow direction properly. Otherwise it

might cause discomfort or cause uneven room

temperatures.

Adjust the horizontal/vertical louver by the remote

control.

To set the horizontal/vertical air flow direction

Perform this function while the unit is in operation.

Use the remote control to adjust the air flow direction.

The vertical/horizontal louver changes approximately 6

degree in angle for each press, the louver can also be set

to swing up, down, left and right automatically.

Please refer to the REMOTE CONTROL USER MANUAL

for details.

IMPORTANT: Do not put your fingers into the panel of

blower and suction side.

The high-speed fan inside may

cause danger.

Do not operate the air conditioner for long periods with

the air flow direction set downward in COOL or DRY

mode. Otherwise, condensation may occur on the

surface of the horizontal louver causing moisture to

drop on to the floor or on furnishings.

When the air conditioner is switched on immediately

after it was stopped, the horizontal louver might not

move for approximately 10 seconds.

Open angle of the horizontal louver should not be set

too small, as COOLING or HEATING performance may

be impaired due to too restricted air flow area.

Do not move the horizontal louver manually. Otherwise

the horizontal louver will be out of sync.

During operation, do not operate with horizontal louver

in closed position to block the air outlet.

When the air conditioner is connected to the power

(initial power), the horizontal louver may generate a

sound for 10 seconds, this is a normal operation.

CAUTION

(Horizontal louver)

Range

(Vertical louver)

How the air conditioner works

1 hour

Set

Temperature

Set

Temperature

COOL mode

HEAT mode

SLEEP operation

1 hour

SLEEP operation

7 hours timer off

AUTO mode

When you set the air conditioner in AUTO mode, it will

automatically select COOL, HEAT or FAN mode

operation depending on the temperature you have

selected and the room temperature.

The air conditioner will control the room temperature

automatically around the temperature point set by you.

If the AUTO mode is uncomfortable, you can set

desired conditions manually.

SLEEP mode

When you press SLEEP button on the remote control

during COOL, HEAT or AUTO mode , the air conditioner

will automatically increase (COOL) or decrease (HEAT)

per hour for the first 2 hours, then hold steadily for

the next 5 hours, and switch off afterwards.

This mode saves energy and brings comfort at night.

DRY mode

COOL mode

The temperature setting are adjustable between 17 C to

30 C . Cooling begins automatically when the room

temperature around 1 C above the set point, and stops

when the room temperature around 1 C below the set

point. The fan will remain running.

HEAT mode

The temperature setting are adjustable between 30 C to

17 C . Heating begins automatically when the room t

emperature around 1 C below the set point, and stops

when the room temperature around 1 C above the set

point. The fan will remain running.

The fan speed will be automatically controlled under the

dry mode.

During the dry mode, if the room temperature is

lower than 10 C, the compressor will stop operation

and restart until the room temperature is above

12 C.

5 hours

Cleaning the Grille, Case and Remote Control

Wipe the indoor unit with a dry cloth if it is dirty.

Do not use a chemically treated cloth or duster to

clean the unit.

Do not use benzine, thinner, polishing powder, or

similar solvents for cleaning. These may cause

the plastic surface to crack or deform.

CAUTION

MAINTENANCE INSTRUCTION

Turn the unit off before cleaning. To clean and wipe

with a soft and dry cloth. Do not use bleach or abrasives.

NOTE: Supply power must be disconnected before

cleaning the indoor unit.

Filter Handle

Cleaning the air filter

A clogged air filter reduces the cooling / heating efficiency of

this unit. Clean the filter every 2 weeks is recommended.

1. Lift the indoor unit panel up to an angle until a click sound

is heard.

2. Hold the handle of the air filter and lift it up slightly

to take it out from the filter holder, then pull it

downwards.

3. Remove the air filter from the indoor unit.

NOTE

Checks before operation

When the unit is not in use for a prolonged period,

please perform the following.

(1) Operate the FAN mode for about half a day to dry inside

of the unit.

(2) Stop the air conditioner and disconnect the power.

Remove the batteries from the remote control.

(3) The outdoor unit requires periodic maintenance

and cleaning. Do not attempt to do this yourself.

Contact your dealer or service provider.

Check if the wiring is broken off or disconnected.

Check if the air filter is installed.

Check if the air outlet or inlet is blocked after the

air conditioner has not been used for a prolonged

period.

Do not touch the metal parts of the unit when

removing the air filter. Injuries can occur when

handling sharp metal edges.

Do not use water to clean inside the air conditioner.

Exposure to water can destroy the insulation and

lead to possible electric shock.

When cleaning the unit, please ensure the

power and the circuit breaker are turned off.

Caution

Air freshening filter

4. Remove the air filter and air freshening filter from its

support frame.

(The air freshening filter include : Tea polyphenols /

Cold catalyst filter . The removing and installation

methods are slightly different, see the pictures marked

on the left. (Clean the air freshening filter at least

once a month is recommended.)

5. Clean the air filter and air freshening filter with a vacuum

cleaner or water, then dry them in a cool and dry place.

6. Install the air freshening filter back into position.

Insert the upper portion of the air filter back into the

unit, make sure that the left and right edges line

up correctly, and place the air filter back into position.

The following events may occur during normal operation.

1. Compressor protection

The compressor cannot restart for 3-4 minutes after it stops.

2. Defrosting

Frost may be generated on the outdoor unit during heat cycle when the outdoor temperature is

low and the humidity is high resulting in lower heating efficiency of the air conditioner.

During this condition, the air conditioner will stop heating operation and start defrosting

automatically.

The time to defrost may vary from approximately 4 to 10 minutes according to the outdoor

temperature and the amount of frost built up on the outdoor unit.

3. White mist coming out from the indoor unit

White mist may come out due to a large temperature difference between the air inlet and air

outlet on COOL mode in an indoor environment that has a high relative humidity.

White mist may come out due to moisture generated from defrosting process when the air

conditioner restarts in HEAT mode operation after defrosting.

4. Low noise of the air conditioner

You may hear a low hissing sound when the compressor is running or has just stopped running.

It is the sound of the refrigerant flowing or coming to stop.

You can also hear a low "squeak" sound when the compressor is running or has just stopped

running. This is caused by heat expansion and cold contraction of the plastic parts in the unit

when the temperature is changing.

A noise may happen due to louver restoring to its original position when the power is turned on.

5. Dust is blown out from the indoor unit.

This is a normal condition when the air conditioner has not been used for a prolonged period or

during first use of the unit.

6. A peculiar smell comes out from the indoor unit.

This is caused by the indoor unit giving off smells permeated from building material, furniture,

or smoke.

7. The air conditioner turns to FAN mode from COOL or HEAT mode.

When indoor temperature reaches the temperature setting on the air conditioner, the compressor will

stop automatically, and the air conditioner will turn to FAN mode. The compressor will start again

when the indoor temperature rises on COOL mode or falls on HEAT mode to the set point.

TROUBLESHOOTING

9. Water leakage

Water leakage may generate on the surface of the indoor unit when cooling in a high

relatively humidity (relative humidity higher than 80%). Adjust the horizontal louver to

the maximum air outlet position and select HIGH fan speed.

10. Heat mode

The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit

during heating operation. When the outdoor temperature falls, heat drawn in by the air

conditioner will decrease accordingly. At the same time, heat loading of the air conditioner

will increase due to larger difference between indoor and outdoor temperature. If a

comfortable temperature can't be achieved by the air conditioner, we suggest you use a

supplementary heating device.

11. Auto-restart function

Power failure during operation will stop the unit completely.

When the power restores, the unit will restart automatically with all the previous settings preserved

by the memory function.

8. The air conditioner runs function after turning off the unit.

When turning off the unit under COOL and DRY mode, the air conditioner will run

function for 7-10 minutes.

then the operation will be stopped and the unit will turn off automatically.

Anti-mildew

If turning off the unit when HEAT mode, the unit will continue operating for about 30 seconds

at LOW fan speed,

Stop the air conditioner immediately if one of the following faults occur. Disconnect the

power and contact the service center.

Fuse blows frequently or circuit breaker trips frequently.

Other objects or water penetrate inside the air conditioner.

The remote control does not work or works abnormally.

Trouble

Malfunctions

Unit does not

start

The cooling /

heating efficiency

is not very well

while air flowing

out from the air

conditioner

Cause

Power cut

Unit unplugged

Fuse may be blown

Battery in the remote control may

be exhausted

The time you have set with the timer

is incorrect

Wait for the power to be restored.

Check if the plug is securely in the wall

receptacle.

Replace the fuse.

Replace the battery.

Wait or cancel the timer setting.

Set the temperature correctly. For

detailed method, please refer to the

Remote Control User Manual .

Clean the air filter.

Close the doors or windows.

Clear obstructions away first, then

restart the unit.

Wait.

Inappropriate temperature setting

Air filter is blocked

Doors or windows are open

Air inlet or outlet of indoor or

outdoor unit has been blocked

Compressor 3 minutes

protection has been activated

If the trouble persists, please contact the customer service center.

Be sure to inform them of the detailed malfunctions and the unit model.

Notes: Do not attempt to repair the unit yourself.

Always consult an authorised service provider.

Solution

OPERATION indicator or other indicators continue flashing and

it cannot be fixed by restarting the air conditioner.

If one of the following code appears on the display area :

E0,E1,E2,E3.....or P0,P1,P2,P3......

TYPES

BODY DIMENSION(mm)

(W x H x D)

WIRING SIZE

(mm )

FSAV10M16

FSAV13M16

835x280x198

3*1.0

FSAV19M16

990x315x218

3*1.5

INDOOR

OUTDOOR

770x555x300

800x554x333

SPECIFICATIONS

WARRANTY

1.The product has 2 years warranty from the date of purchase.

2.The warranty shall not apply:

A.to any product subjected to misuse, alteration, act of God, improper handling, improper

transport, improper testing or unauthorized repair;

B.to cosmetic problems or defects which result from normal wear and tear under ordinary

use yet not affecting the performance or use of the product;

C.if the product is disassembled or altered;

D.to any packing, transportation, export / import tax or any related expenses.

Within warranty coverage period, all checking, repair and spare parts cost will be waived for

those defects arising from normal usage. Free replacements of spare parts do not include

the following:

Any filter, outer cabinet, plastics accessories

Product not used for personal or domestic purpose

3.CUSTOMER MUST PRESENT THE SALES INVOICE OR RECEIPT FOR 2 YEARS

WARRANTY SERVICES.

4.All require for service, please contact Fortress Service Centre Hotline, Tel: 2555 -5788

NOTES

This appliance must be plugged or connected into a specific 220-240V socket. Please

make sure the plug is fully plugged-in before use. Do not use any adapter or extension cord.

This appliance is a high energy consumption product, please do not use it with other high

energy consumption products in the same supply socket.

THE APPLIANCE IS FOR HOUSEHOLD USE ONLY.

ENVIRONMENT

Do not throw away the appliance with the normal household waste at the end

of its life, but hand it in at an official collection point for recycling. By doing this,

you help preserving the environment.

IMPORTANT NOTICES

IN NO EVENT SHALL OUR COMPANY OR THE SUPPLIER BE LIABLE TO YOU OR ANY OTHER

PARTY FOR ANY DIRECT, INDIRECT, GENERAL SPECIAL, INCIDENTAL, CONSEQUENTIAL,

EXEMPLARY OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE

THE PRODUCT (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR INJURY, LOSS OF

PROPERTY, BUSINESS PROFITS, BUSINESS INTERRUPTION) OR FROM ANY BREACH

OF WARRANTY, EVEN IF OUR COMPANY OR SUPPLIER HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. IN NO CASE SHALL OUR COMPANY OR SUPPLIER'S

LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE PRODUCT.

Specifications, designs and dimensions are subject to change without prior notice.

䆺乫࠶億ߧ≓₏

֯⭘䃚᰾ᴨ

ර

ර㲏

FSAV10M16 FSAV13M16 FSAV13M16

֯⭘ᡆᆹ㼍ᵜ⭒૱ࡽˈ䃻Ԅ㍠䯡䆰ᵜ䃚᰾ᴨˈ৺ᡰᴹᆹޘ⌘᜿һ丵ˈі䃻࿕ழ؍ᆈˈ

ԕۉᰕᖼ৳㘳ḕ䯡Ǆ



ⴞⴞ䤴䤴



ᆹᆹޘ⌘᜿һ丵



⭒⭒૱䴦䴦ԦԦӻ㍩



᫽᫽֌䃚᰾



؍؍伺ᤷ⽪



⯁⯁䴓ሿⲮ、



㾿㾿Ṭ㺘



؍؍⭘ᵏ䋷ᯉ





䯡䆰ᵜ֯⭘䃚᰾ᴨ

ᵜ֯⭘䃚᰾ᴨᨀ׋Ҷ䁡ཊᴹ䰌ߧ≓₏Ⲵ↓⻪֯⭘㠷؍伺ሖ⭘ᨀ⽪ˈਚ㾱〽࣐⌘᜿ˈ

ቡ㜭ᔦ䮧ߧ≓₏Ⲵ֯⭘༭ભǄ൘⯁䴓ሿⲮ、ѝˈਟԕ᢮ࡠ䁡ཊᑨ㾻୿乼Ⲵ䀓⊪ᯩ⌅Ǆ

㚟㎑㏝؞ѝᗳࡽˈ䃻ݸ☿㿭⯁䴓ሿⲮ、Ǆ



ἧ䓐ࡽˈ䃻㚟㎑ሸ䮰Ⲵᢰ㺃Ӫ଑䙢㹼ᆹ㼍Ǆ



⌘᜿



x 䃻㚟㎑ᦸ℺Ⲵᢰ㺃Ӫ଑䙢㹼㏝؞ᡆ؍伺ᵜ⭒૱Ǆ

x 䃻㚟㎑ᦸ℺Ⲵᢰ㺃Ӫ଑ᆹ㼍ᵜ⭒૱Ǆ

x 䲔䶎ᴹᆹޘӪ଑Ⲵᤷሾᡆ঄ࣙлˈі⻪؍֯⭘㘵Ⲵᆹޘˈ੖ࡷᵜ₏ಘнਟ⭡ނㄕǃ

㋮⾎⯵Ӫǃ⇈⯮Ӫ༛৺৽៹䙾ធѻӪ༛֯⭘Ǆ

x ࠷य䇃ނㄕᢺ⧙ߧ≓₏Ǆ

x 䴫Ⓚ㐊ਚ㜭⭡ᔐᯩᦸ℺Ⲵᢰ㺃Ӫ଑ᡆ਼⁓ਸ䋷ṬⲴᢰ㺃Ӫ଑䙢㹼ᴤᨋˈԕݽⲬ⭏

᜿ཆǄ

x ␵▄ᡆ؍伺ࡽˈ䃻ݸ䰌ᦹ䴫Ⓚ㠷׋䴫ᯧ䐟ಘǄ

ᆹޘ⌘᜿һ丵



⛪䚯ݽ䙐ᡀԫօӪ䓛ۧᇣԕ৺䋑⭒ᨽཡˈ䃻䚥ᆸԕлᤷᕅǄ



Ƶᵜ֯⭘䃚᰾ᴨᡰ֯⭘ㅖ㲏Ⲵਜ਼㗙ྲл˖



࠷यว㹼Ǆ



ᗵ丸ว㹼Ǆ



ਟ

ਟ㜭䙐ᡀ↫ӑᡆ㘵೤䟽ۧᇣ



[䴫䴫Ⓚ㐊ннਟ䶐䘁ਟ⟳≓

億ᡆ᱃⟳⢙ˈྲ⊭⋩ǃ

㤟ǃ〰䟻ࣁㅹ

⮦⮦ߧ≓₏䙻㹼ᱲˈ䃻䰌к䮰

デ

[нਟᨽ༎䴫Ⓚ㐊㐊ᡆ֯⭘

нㅖਸ㾿ṬⲴ䴫Ⓚ㐊

ƽ੖ࡷਟ㜭ሾ㠤⠶⛨ᡆ⚛

⚭

ƽ੖ࡷᴳᖡ丯㼭ߧᡆ㼭᳆᭸

᷌

ƽ੖ࡷᴳሾ㠤䀨䴫ᡆ⚛⚭

ƽྲ᷌䴫Ⓚ㐊ᐢ㏃ᨽ༎ˈ

ᗵ丸⭡㼭䙐୶ǃᐢ㏃ᦸ

℺Ⲵ㏝؞ѝᗳᡆ㘵ਸ䋷

ṬⲴӪ༛䙢㹼ᴤᨋˈԕ

ݽ䙐ᡀড䳚

[нਟᴤ᭩䴫Ⓚ㐊㐊䮧ᓖᡆ

㠷ަԆ䴫ಘޡ⭘ᨂᓗ

[᡻ᵚᬖҮˈнਟ᫽֌ߧ≓₏

[䘱付ਓн㾱ⴤ᧕ሽ㪇ᡯ

䯃ޗⲴӪ

ƽ੖ࡷᴳഐ⛪䙾⟡㘼ሾ㠤

䀨䴫ᡆ⚛⚭

ƽ੖ࡷᴳ䀨䴫

ƽ੖ࡷᴳᴹᨽڕᓧ

ġ 䃻䃻ᗵ丸⻪ᇊ᧕ൠ࿕⮦

[н㾱ᔴ★ᑦ䴫䜘ԭ

उउᗵᆹ㼍ᯧ䐟ಘԕ৺ሸ

䮰Ⲵ䴫Ⓚ䴫䐟

ƽ᧕ൠн⮦ਟ㜭ሾ㠤䀨䴫

ƽ੖ࡷਟ㜭ᕅ䎧ߧ≓₏᭵䳌

ᡆ䀨䴫

ƽᆹ㼍н⮦ᴳሾ㠤⚛⚭ᡆ

䀨䴫

ġ ྲྲ᷌ߧ≓₏ࠪ⨮ᙚ㚢ǃ

⮠ણᡆ㘵߂➉ˈ䃻・ণ

ᯧ䴫

[䴫Ⓚ㏛нਟ䶐䘁⟡Ⓚ

䃻य䘿䙾䮻䰌䴫Ⓚ᫽֌ᡆ

ڌ→ᵜ₏

[ߧߧ≓₏䙻䕹ᱲˈн㾱ᢃ

䮻₏䓛

ƽ੖ࡷਟ㜭ሾ㠤⚛⚭ᡆ䀨

䴫

ƽ੖ࡷਟ㜭ሾ㠤⚛⚭ᡆ䀨䴫

ƽ੖ࡷਟ㜭䀨䴫

ྲྲ ᷌ ᴮ ㏃ ࠪ ⨮ ➔ ≓ ⋴

┿ˈ֯⭘ߧ≓₏ࡽ䃻ݸ

ሽᡯ䯃䙢㹼䙊付

ġ 䃻䃻࿕ழ䙓᧕䴫Ⓚ

[нਟ᣶নᡆ᭩㼍ߧ≓₏

ƽ੖ࡷਟ㜭ሾ㠤⠶⛨ǃ⚛

⚭ᡆ⠂ۧ

ƽ੖ࡷਟ㜭ሾ㠤䀨䴫ᡆ⚛⚭

ƽ੖ࡷਟ㜭ሾ㠤᭵䳌ᡆ䀨

䴫





᝾᝾֋







ਟ㜭䙐ᡀۧᇣᡆ䋑⭒ᨽཡ



[᣶᣶䲔オ≓䙾☮☮㏢ᱲˈн

㾱᧕䀨ߧ≓ ₏Ⲵ 䠁ኜ

䜘ԭ

[н㾱⭘≤␵⍇ߧ≓₏ޗ䜘

⮦㠷᳆⡀ㅹа䎧䎧֯

⭘ᱲˈ㾱؍ᤱᡯ䯃

䙊付㢟ྭ

ƽ੖ࡷᴳਇۧ

ƽྲ᷌ᴹ≤䙢ޕߧ≓₏ˈᴳ

ᖡ丯㎅㐓࣏㜭ˈਟ㜭ሾ㠤

䀨䴫

ƽ੖ࡷᴳࠪ⨮㕪≗



␵ ▄ ᡆ ㏝ ؞ ߧ ≓ ₏

ࡽˈ㾱䰌ᦹ䴫Ⓚˈі䰌

䮹ᯧ䐟ಘ

[н㾱ᢺሥ⢙ᡆἽ⢙↓ሽ䘱

付ਓ

[н㾱࡙⭘ߧ≓₏ֶ؍

䆧㋮ᇶܰಘǃ؍ᆈ伏

૱ǃ➗亗ሥ⢙㠷Ἵ⢙ǃ

؍㇑㰍㺃૱ㅹ

ƽ䙊䴫ᱲн㾱␵▄ߧ≓

₏ˈ੖ࡷਟ㜭ሾ㠤⚛⚭

ᡆ䀨䴫ˈ䙐ᡀӪ䓛ۧᇣ



ƽ੖ࡷᴳሽሥ⢙ᡆἽ⢙䙐ᡀ

ۧᇣ

ƽ੖ࡷਟ㜭䙐ᡀ䋑⢙ਇ

ᨽ

⣲付᳤䴘ᱲˈ䃻䰌ᦹߧ

≓₏і䰌䮹デᡦ

[н㾱伢⭘ߧ≓₏ⲴⲴߧࠍ≤

 䮧䮧ᵏн֯⭘ߧ≓₏ᱲ

䃻䰌ᦹѫ䴫Ⓚ䮻䰌

ƽ↔ᱲᢃ䮻デᡦᴳሾ㠤

ᇔޗ▞★ˈі䇃ےާਇ

▞

ƽ≤ѝਜ਼ᴹ䴌䌚ˈᴳ֯Ӫ⭏

⯵

ƽ੖ࡷਟ㜭ሾ㠤⭒૱᭵

䳌ᡆ⚛⚭

[н㾱൘䙢≓ਓ䱴䘁ᡆ

ᧂ≓ਓޗ䜘 ᭮㖞 ԫօ

⢙Ԧ

⻪⻪؍᭮ᯬᇔཆⲴᆹ㼍ᷦн

ᴳഐ⛪䮧ᵏཆ䵢㘼ਇᨽ

उउᗵപᇊྭ

䨢㯋忶

☮

㏢ˈᔪ䆠⇿ޙᱏᵏ␵▄

а⅑

ƽ੖ࡷᴳሾ㠤ߧ≓₏᭵

䳌ᡆ᜿ཆ

ƽྲ᷌ᆹ㼍ᷦਇᨽˈߧ≓₏

ਟ㜭ໞлˈ䙐ᡀ⹤༎

ƽн࣐オ≓䙾☮㏢䙻

䕹ˈਟ㜭ሾ㠤᭵䳌

[н㾱֯⭘〰䟻ࣁㅹᕧ

࣋␵▄ࣁˈਚ㜭֯⭘Ү

ᐳ

[нн㾱൘䴫Ⓚ㐊кк᭮㖞ԫօ

⢙૱ˈ⻪؍䴫Ⓚ㐊⋂ᴹ㻛

ᬐ༃

 

ƽਟ㜭ᴳሾ㠤ߧ≓₏㽚

㢢ǃ㺘䶒㻛࡞㣡ˈ⹤༎

ཆ㿰

䮻㇡৺ᆹ㼍ᱲᗵ丸ሿ

ᗳˈ䤂࡙䚺㐓ᇩ᱃䙐

ᡀۧᇣ



ƽ੖ࡷᴹ⚛⚭ᡆ䀨䴫ড䳚



ྲ᷌ߧ≓₏䙢≤ˈ䃻俜к

䰌䮹ߧ≓₏৺ᯧ䐟ಘǄ

ᤄࠪ䴫Ⓚᨂ九ˈі㠷ਸ

䋷ṬⲴ㏝؞ᢰ㺃Ӫ଑㚟

㎑



λλЈ

⭒

⭒૱䴦Ԧӻ㍩

࠻ϣᐒ

ࡰҢᐩ

࠻ϣᐒ

1. ߻य़݈

2. Ε॥α

3. ޜ਻ၸᘠᆛ

4. р॥α

5. Нѳଌ॥ယ

6. ࠟޔଌ॥ယ

7. ᡉҢࡀჿ

࠻Ѧᐒ

8. ೱௗᆅၰ

9. ೱௗႝጕ

10. ᓸΚሚ

ຏǺ

ҁ䁃ܴਜϣޑ܌ԖკТѝٮୖԵǶாޑհ਻

ᐒёૈౣԖόӕǴ΋ཷаჴނࣁྗǶ

ࡰҢᐩ

ନᗩᗩࡰҢҢᐩ˄Defrost˅˅Ǻ

Ԝᐩߝଆਔж߄հ਻ᐒςԾ୏໒௴ନ

ᗩ

фૈ܈ς௴୏ཪ਻௓ڋфૈǶ

ၮբࡰࡰҢᐩ(Run)ǺǺ

Ԝᐩߝଆਔж߄հ਻ᐒ҅ӧၮբύ

ۓਔ೛೛ۓࡰҢᐩ(Timer)ǺǺ

Ԝᐩߝଆж߄ۓਔ

೛ۓς௴୏Ƕ

ᡉҢࡀჿǺǺ

հ਻ᐒၮբਔᡉҢྕࡋ೛ۓǶ

ᡉҢࡺምжဦǶ

࠻ѦѦᐒ

Page is loading ...

Fortress Technologies FSAV10M16 User manual

Brand: Fortress Technologies

Model: FSAV10M16

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

Download PDF

report

Fortress Technologies FSAV10M16 User manual

This manual is also suitable for

Fortress Technologies FSAV10M16 User manual

Related papers

Other documents