Metos LL600 Operating instructions

Brand: Metos

Model: LL600

Type: Operating instructions

This manual is also suitable for

LL800
LLM800

HEATED PLATE

LLM

TYPE: 600, 800

Installation and Operation Manual

S/N: 045610/01 Rev.: 2.1

13.3.2006 Rev. 2.1

Dear Customer,

Congratulations on deciding to choose our appliance for your kitchen activities. You

made an excellent choice. We will do our best to make you a satisfied customer like thou-

sands of customers we have around the world.

Please read this manual carefully. You will learn correct, safe and efficient working meth-

ods in order to get the best possible benefit from the appliance. The instructions and hints

in this manual will give you a quick and easy start, and you will soon note how nice it is

to use this equipment.

All rights are reserved for technical changes.

You will find the main technical data on the rating plate fixed to the equipment. When you

need service or technical help, please let us know the serial number shown on the rating

plate. This will make it easier to provide you with correct service.

For your convenience, space is provided below for you to record your local service con-

tact information.

Service phone number:...............................................................................................

Contact person:....................................................................................................................

13.3.2006 Rev. 2.1

13.3.2006 Rev.

1. General .......................................................................................................... 1

1.1 Symbols used in the manual .......................................................................................... 1

1.2 Symbols used on the appliance ...................................................................................... 1

1.3 Checking the relationship of the appliance and the manual .......................................... 1

2. Safety .............................................................................................................. 2

2.1 Safe use of the appliance ............................................................................................... 2

2.2 Safety instructions in case of malfunction ..................................................................... 2

2.3 How to dispose of the appliance .................................................................................... 2

3. Functional description .................................................................................. 3

3.1 Intended use of the appliance ........................................................................................ 3

3.1.1 Use for other purposes ........................................................................................... 3

3.2 Control panel switches .................................................................................................. 3

3.3 Operating principle ........................................................................................................ 4

4. Operation instructions ................................................................................. 5

4.1 Operation procedures ..................................................................................................... 5

4.1.1 General ................................................................................................................... 5

4.1.2 How to use the hot plate ........................................................................................ 5

4.2 After use ........................................................................................................................ 6

4.2.1 Cleaning ................................................................................................................ 6

4.2.2 Service ................................................................................................................... 6

5. Installation ..................................................................................................... 7

5.1 Packing .......................................................................................................................... 7

5.2 Siting the hot plate ......................................................................................................... 7

5.3 Electricity connection .................................................................................................... 7

5.4 Test-run ......................................................................................................................... 7

6. Troubleshooting ............................................................................................ 8

7. Spare parts .................................................................................................... 9

7.1 Voltage codes .............................................................................................................. 11

7.2 Product codes ............................................................................................................... 11

8. Technical specifications .............................................................................. 19

13.3.2006 Rev.

13.3.2006 Rev. 2.1

General

1. General

Carefully read the instructions in this manual as they contain important information re-

garding proper, efficient and safe installation, use and maintenance of the appliance.

Keep this manual in a safe place for eventual use by other operators of the appliance.

The installation of this appliance must be carried out in accordance with the manufactur-

er’s instructions and following local regulations.

Persons using this appliance should ensure they are familiar with the proper and safe use

of it.

Switch off the appliance in case of failure or malfunction. Have the appliance serviced by

a technically qualified person authorized by the manufacturer and using original spare

parts.

Not complying with the above may put the safety of the appliance in danger.

1.1 Symbols used in the manual

This symbol informs about a situation where a safety risk might be at hand. Given instruc-

tions are mandatory in order to prevent injury.

This symbol informs about the right way to perform in order to prevent bad results, appli-

ance damage or hazardous situations.

This symbol informs about recommendations and hints that help to get the best perform-

ance out of the appliance.

1.2 Symbols used on the appliance

This symbol on a part informs about electrical terminals behind the part. The removal of

the part must be carried out by qualified persons only.

1.3 Checking the relationship of the appliance and the manual

The name plate of the appliance indicates the serial number of the appliance. If the man-

uals are missing, it is possible to order new ones from the manufacturer or the local rep-

resentative. When ordering new manuals it is essential to quote the serial number shown

on the rating plate.

13.3.2006 Rev. 2.1

Safety

2. Safety

2.1 Safe use of the appliance

Because the appliance has hot surfaces during normal use, the following warnings and in-

structions should be observed:

• During long-time operation even the frame of the appliance gets hot.

• The capability of the appliance to store and even out heat also keeps it hot for a

long time after switching it off.

• Depending on temperature setting, the surface of the plate can be burning hot. For

safe handling of dishes it is recommended to use heat protective gloves.

• Do not leave the appliance on for long periods totally without supervision.

2.2 Safety instructions in case of malfunction

In the event of fault or malfunction, switch the appliance off by unplugging the connection

cable from the socket. Contact an agent authorised by the manufacturer and use original

spare parts.

2.3 How to dispose of the appliance

Once the appliance has reached the end of its useful life, it must be disposed of in com-

pliance with local rules and regulations.

The best way of dealing with or recycling any substances which have a potentially adverse

impact on the environment is to dispose of them through a proper waste company.

13.3.2006 Rev. 2.1

Functional description

3. Functional description

3.1 Intended use of the appliance

The hot plates LL-600, LL-800 and LLM-800 are designed for holding the serving tem-

perature of foods and drinks.

3.1.1 Use for other purposes

Use of the hot plate for any other purpose than that mentioned above is prohibited.

The manufacturer shall not be held liable for any situations which may arise from failure

to comply with the warnings and instructions given in this manual.

3.2 Control panel switches

LL-600 and LL-800

1. Power regulator (position 0: power off, position 1: full power)

2. Yellow pilot light PLATE SWITCHED ON

13.3.2006 Rev. 2.1

Functional description

LLM-800

1. Power regulator (position 0: power off, position 1: full power)

2. Yellow pilot light PLATE SWITCHED ON

3. Switch for heating lamps (position 0: lamps off, position 1: lamps on)

3.3 Operating principle

The heat surface of the hot plate is heated by heating elements located under the surface.

Heat is distributed evenly on the heat surface by means of a heat transfer plate. The tem-

perature of the plate is steplessly controlled by a power regulator. The intervals of the

heating cycles (heating elements on) depend on how far clockwise the power regulator has

been turned. Full power is achieved by turning the power regulator to position 1. The heat-

ing elements are then continuously on (100 % power).

The yellow pilot light indicates that the plate has been switched on. The pilot light goes

out when you switch off the plate by turning the power regulator to position 0.

Since the power regulator is not thermostatically controlled, the surface temperature of the

hot plate seeks, depending on the set value, a so called equilibrium, which means that

thermal power received by the environment and products and thermal power released by

the appliance are the same. For this reason, the temperature of the hot plate may somewhat

vary depending on the load although the set values remain unchanged.

The LLM-800 model is equipped with a sneeze guard and two heating lamps. The heating

lamps have a separate ON/OFF switch on the front panel, fitted with a yellow pilot light.

321

13.3.2006 Rev. 2.1

Operation instructions

4. Operation instructions

4.1 Operation procedures

4.1.1 General

There is a slight smell of metal and thermal insulation when the plate is heated for the first

time. This is completely normal and disappears by heating.

4.1.2 How to use the hot plate

The power regulator functions both as a current switch and a temperature regulator. When

you turn the power regulator, the plate goes on and the yellow lamp lights up. The pilot

lamp is continuously on as long as the plate is switched on. The temperature will stepless-

ly increase while turning the power regulator clockwise. Full power is obtained by turning

the regulator on continuous duty (100 %) to position 1. The heating elements are then con-

tinuously on, so the surface temperature of the plate without load may rise even up to 160-

170°C. When you do not need the hot plate, switch it off by turning the power regulator

to position 0 (pilot lamp goes out).

The LLM-800 model has an ON/OFF switch for heating lamps on the front panel. When

not needed, the heating lamps should be turned off.

When empty, the surface plate is partly separate from the heat transfer plate, which means

that the surface temperature of the hot plate is lower than the set value. The weight of a

dish, however, causes the surface to press against the heat transfer plate, so the following

settings can be regarded as guiding temperatures:

• 1/4 turn: approx. 35°C

• 1/2 turn: approx. 75°C

• 3/4 turn: approx. 125°C

Depending on the temperature setting, the surface of the hot plate as well as the heating

lamps of the LLM-800 model can be extremely hot.

13.3.2006 Rev. 2.1

Operation instructions

4.2 After use

4.2.1 Cleaning

Use of a hose or pressure washer for cleaning the hot plate is forbidden.

When cleaning the hot plate, observe that the surface is hot quite a long time after use.

Hot plates are electrical appliances, which means that there are restrictions regarding

cleaning them with water. Cleaning is permitted only with a damp cloth to avoid water

getting into the air inlets. Depending on how dirty the hot plate is, use an alkaline sub-

stance which can be diluted in a spray bottle to loosen grease.

Do not use steel wool or abrasive pads in cleaning. Once a surface is scratched, dirt sticks

to it much more easily.

4.2.2 Service

This appliance does not contain parts which can be serviced by the user. Maintenance

must be carried out by an authorised agent.

In the event of fault or malfunction, switch the appliance off at the mains. Contact an agent

authorised by the manufacturer and use original spare parts.

13.3.2006 Rev. 2.1

Installation

5. Installation

5.1 Packing

The LL-600 and LL-800 models are delivered in cardboard boxes. The adjustment pads

and fixing screws come in a plastic bag.

The LLM-800 model, assembled in the factory, is packed in a wooden box. The heating

lamps are delivered with the appliance, in packages.

5.2 Siting the hot plate

Adjust the legs so that the hot plate stands steadily on the worktop. The legs can be slightly

adjusted by turning the screws on the legs, either clockwise or anticlockwise. When fixing

the legs, be careful that the connection cable does not get jammed under the plate.

To prevent damage, the top of the hot plate must not be used as a worktop on a construc-

tion site or during installation.

5.3 Electricity connection

Before connecting the appliance to the mains, make sure that the connection cable is not

damaged. Connect the plug to an earthed 230V socket.

All information needed to connect the hot plate is to be found on the name plate, the con-

nection diagram and the installation drawings.

5.4 Test-run

Please read the operation instructions before using the appliance.

Test the appliance once it has been connected to the mains electricity.

Check that

• the yellow pilot lamp lights up when the hot plate is switched on by turning the

power regulator

• the plate warms up. When empty, the surface plate is partly separate from the heat

transfer plate, so temperature differences may be felt when touching the surface by

hand

• the heating lamps and the yellow pilot light for the ON/OFF switch turn on when

the lamps are switched on.

13.3.2006 Rev. 2.1

Troubleshooting

6. Troubleshooting

If the appliance fails to work, check to ensure

• that it has been used according to the instructions

• that the electric plug has been connected

• that the circuits breakers (fuses) on the distribution board are in working order.

Ask a qualified person to check overload protection.

Should the hot plate still not work, contact an authorised agent. Before phoning, make

sure you have at hand the appliance type and serial number to be found on the name plate

on the bottom of the appliance.

13.3.2006 Rev. 2.1

Spare parts

7. Spare parts

General parts and electric components13

General parts and electric components15

Sneeze guard, illumination ..................17

13.3.2006 Rev. 2.1

Spare parts

13.3.2006 Rev. 2.1

Spare parts

7.1 Voltage codes

7.2 Product codes

Voltage Voltage code

A3/N/PE∼400/230V 50Hz

B ∼250V 16A 50Hz

C3/N/PE∼380/220V 50Hz

D3/PE∼200V 50-60Hz

F2/PE 220−240V 50Hz

G3/N/PE∼415/240V 50Hz

H3/PE∼230V 50Hz

I3/PE∼220V 60Hz

J3/PE∼380 50Hz

K3/PE∼400V 50Hz

L3/PE∼415V 50Hz

M3/PE∼440V 60Hz

N3/PE∼460V 60Hz

O3/PE∼480V 60Hz

P 1/N/PE~220-240V 50Hz

R 2/PE~220-230V 60Hz

S3/N/PE∼400/230V 50Hz

T3/PE∼230V 60Hz

U 1/N/PE~100V 50-60Hz

Product code Full name

Model codes

LL Heated plate LL

LLM Heated plate LLM

Type codes

600 600

800 800

13.3.2006 Rev. 2.1

Spare parts

13.3.2006 Rev. 2.1

Spare parts

LL=LL, LLM=LLM

600=600, 800=800

F=2/PE 220−240V 50Hz, P=1/N/PE~220-240V 50Hz

ID Code Model Type Voltage Description

Module:General parts and electric components

10 3594585 LL 600 Sheating

10 3594578 LL 800 Sheating

10 3672107 LLM 800 Sheating

20 3594546 LL 600 Heat distributor

20 3594497 LL 800 Heat distributor

20 3672115 LLM 800 Heat distributor

30 3594521 LL 600 Support plate

30 3594514 LL 800 Support plate

30 3672117 LLM 800 Support plate

40 3594602 LL 600 F,P Heating element 500W, E1

40 3594602 LL,LLM 800 F,P Heating element 500W, E1, E2

50 3594539 LL 600 Isolation

50 3594507 LL 800 Isolation

50 3672114 LLM 800 Isolation

60 3594553 LL 600 Framework

60 3594472 LL 800 Framework

60 3672106 LLM 800 Framework

70 3750369 LL,LLM Mains cable, X2

80 K382520 LL 600 Strain reliever

80 K382520 LLM 800 Strain reliever

90 3594627 Rubber foot

13.3.2006 Rev. 2.1

Spare parts

Page is loading ...

Metos LL600 Operating instructions

Brand: Metos

Model: LL600

Type: Operating instructions

This manual is also suitable for

LL800
LLM800

Download PDF

report

Metos LL600 Operating instructions

This manual is also suitable for

Metos LL600 Operating instructions

Related papers

Other documents