2. Artec
  3. TUBE5

Artec TUBE5, TUBE5C Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Artec TUBE5 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
TUBE5H & TUBE5C Guitar Amplifier
OPERATING INSTRUCTIONS
TUBE5H
- OUT PUT POWER : 5W (RMS)
- VALVES: 12BH7 x 1 , 12AX7 x 1
- DIMENSIONS : w454 X d228 X h185(mm)
- WEIGHT : 7.8 (kg)
- FUSE : 100V~120V : T2A,250V
220V~240V : T1A,250V
T110
- DIMENSIONS : w454 X d248 X h407mm)
- WEIGHT : 12 (kg)
- SPEAKER : 10” x 1(16 Ohm)
- POWER RATING : 40WATTS
TUBE5C
- OUT PUT POWER : 5W (RMS)
- VALVES: 12BH7 x 1 , 12AX7 x 1
- SPEAKER : 10”x 1 (16 ohm)
- DIMENSIONS : w454 X d248X h389(mm)
- WEIGHT : 14 (kg)
- FUSE : 100V~120V : T1A,250V
220V~240V : T0.5A,250V
SPECIFICATIONS
Front Panel
CONTROL FUNCTIONS
TUBE5H
Front Panel
CONTROL FUNCTIONS
TUBE5C
1. POWER
This power switch is used to turn the amplifier on and off.
You should always turn this switch on before turning on the Stand switch.
2. STANDBY
Always turn this switch on at least 30 seconds after the power switch on.
3. SHAPE
Shape works in Conjunction with Equalizer controls.
4. TREBLE
Treble control
5. MIDDLE
Mid-range control
6. BASS
Bass control
7. VOLUME
Volume control of clean channel
8. CH/SEL
Channel select switch (drive when push) volume control of drive channel.
9. VOLUME
Volume control of drive channel
10. GAIN
This control set the amount of compression and distotion from the amplifier.
11. INPUT
Input plug your guitar in here.
12. LEVEL
This switch sets the effects loop to +4dBV / -10dBV.
13. RETURN
Serial loop return
14. SEND
Serial loop send
15. FOOT SWITCH
The supplied footswitch is connected here
16. 1 x 8Ω
The output marked “1x8 Ohm ” is for the connection of either a single 8 Ohm ectension cabinet.
17. 2 x 16Ω
The output marked “2x16 Ohm ” is for the connection of either two16 Ohm ectension cabinet.
18. 1 x 16Ω
The output marked “1x16Ohm ” is for the connection of either a single 16 Ohm ectension cabinet.
19. PHONES
Phone jack (speaker is off when plug in)
20. AC INPUT
Power Input Connector
1. POWER
This power switch is used to turn the amplifier on and off.
You should always turn this switch on before turning on the Stand switch.
2. STANDBY
Always turn this switch on at least 30 seconds after the power switch on.
3. SHAPE
Shape works in Conjunction with Equalizer controls.
4. TREBLE
Treble control
5. MIDDLE
Mid-range control
6. BASS
Bass control
7. VOLUME
Volume control of clean channel
8. CH/SEL
Volume control of clean channel
9. VOLUME
Volume control of drive channel
10. GAIN
This control set the amount of compression and distotion from the amplifier.
11. INPUT
Input plug your guitar in here.
12. LEVEL
This switch sets the effects loop to +4dBV / -10dBV.
13. RETURN
Serial loop return
14. SEND
Serial loop send
15. FOOT SWITCH
The supplied footswitch is connected here
16. 1 x 8Ω
The output marked “1x8 Ohm ” is for the connection of either a single 8 Ohm ectension cabinet.
17. 2 x 16Ω
The output marked “2x16 Ohm ” is for the connection of either two16 Ohm ectension cabinet.
18. 1 x 16Ω
The output marked “1x16Ohm ” is for the connection of either a single 16 Ohm ectension cabinet.
19. PHONES
Phone jack (speaker is off when plug in)
20. AC INPUT
Power Input Connector
Rear Panel
Rear Panel
/