2. Axxess
  3. AX-ALOC10

Axxess AX-ALOC10 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Axxess AX-ALOC10 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
AX-ALOC10
AX-ALOC10
AX-ALOC10
AX-ALOC10
AX-ALOC10
AX-ALOC10
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
The AX-ALOC10 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 30
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers. This device is most commonly
installed in the trunk when a subwoofer system is being added
to
the OEM stereo system. Please refer to the wiring diagram
for the input connection details.
Wire Color & Function: The audio and power input wire colors
are an EIA standard for car stereo applications as follows.
INPUT HARNESS
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK = Reference Ground (-)
(REFERENCE GROUND OPTIONAL IF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ALOC10. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ALOC10 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 30
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers. This device is most commonly
installed in the trunk when a subwoofer system is being added
to the OEM stereo system. Please refer to the wiring diagram
for the input connection details.
Wire Color & Function: The audio and power input wire colors
are an EIA standard for car stereo applications as follows.
INPUT HARNESS
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK = Reference Ground (-)
(REFERENCE GROUND OPTIONALIF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ALOC10. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ALOC10 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 30
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers. This device is most commonly
installed in the trunk when a subwoofer system is being added
to the OEM stereo system. Please refer to the wiring diagram
for the input connection details.
Wire Color & Function: The audio and power input wire colors
are an EIA standard for car stereo applications as follows.
INPUT HARNESS
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK = Reference Ground (-)
(REFERENCE GROUND OPTIONALIF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ALOC10. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ALOC10 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 30
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers. This device is most commonly
installed in the trunk when a subwoofer system is being added
to the OEM stereo system. Please refer to the wiring diagram
for the input connection details.
Wire Color & Function: The audio and power input wire colors
are an EIA standard for car stereo applications as follows.
INPUT HARNESS
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK = Reference Ground (-)
(REFERENCE GROUND OPTIONALIF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ALOC10. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ALOC10 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 30
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers. This device is most commonly
installed in the trunk when a subwoofer system is being added
to the OEM stereo system. Please refer to the wiring diagram
for the input connection details.
Wire Color & Function: The audio and power input wire colors
are an EIA standard for car stereo applications as follows.
INPUT HARNESS
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK = Reference Ground (-)
(REFERENCE GROUND OPTIONALIF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ALOC10. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
The AX-ALOC10 should be installed on a stereo’s speaker
output wires or the output wires on an OEM amplier of up to 30
watts per channel. These wires can be found behind the stereo
in the dash, on the outside of an OEM amplier, or on the input
terminals on the OEM speakers. This device is most commonly
installed in the trunk when a subwoofer system is being added
to the OEM stereo system. Please refer to the wiring diagram
for the input connection details.
Wire Color & Function: The audio and power input wire colors
are an EIA standard for car stereo applications as follows.
INPUT HARNESS
WHITE = LEFT Front (+) Input
WHITE/BLACK = LEFT Front (-) Input
GRAY = RIGHT Front (+) Input
GRAY/BLACK = RIGHT Front (-) Input
BLACK = Reference Ground (-)
(REFERENCE GROUND OPTIONALIF NOISE IS PRESENT)
NOTE: Be sure that all audio input connections are polarized or
in phase with each other. That is, the positive output wires from
the audio source need to be connected to the corresponding
positive input wires of the AX-ALOC10. The same goes for the
negative audio wires. Failure to do this will result in poor bass
response and low quality audio.
AX-ALOC10
AX-ALOC10
AX-ALOC10
AX-ALOC10
AX-ALOC10
AX-ALOC10
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
1-800-221-0932
axxessinterface.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
1-800-221-0932
axxessinterface.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
1-800-221-0932
axxessinterface.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
1-800-221-0932
axxessinterface.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
1-800-221-0932
axxessinterface.com
The AX-ALOC10 is designed to convert speaker level
audio to line level audio. This allows for the installa-
tion of line level products such as ampliers, EQs and
crossovers on systems that do not have RCA line level
outputs.
Features:
30 Watts Maximum Input, 6:1 Step Down with Fixed
Outputs, Gold Flashed RCAs, Attractive & Durable
Enclosure.
2 CHANNEL, FIXED LINE-OUTPUT CONVERTER
The AX-ALOC10 is designed to convert speaker level
audio to line level audio. This allows for the installa-
tion of line level products such as ampliers, EQs and
crossovers on systems that do not have RCA line level
outputs.
Features:
30 Watts Maximum Input, 6:1 Step Down with Fixed
Outputs, Gold Flashed RCAs, Attractive & Durable
Enclosure.
2 CHANNEL, FIXED LINE-OUTPUT CONVERTER
The AX-ALOC10 is designed to convert speaker level
audio to line level audio. This allows for the installa-
tion of line level products such as ampliers, EQs and
crossovers on systems that do not have RCA line level
outputs.
Features:
30 Watts Maximum Input, 6:1 Step Down with Fixed
Outputs, Gold Flashed RCAs, Attractive & Durable
Enclosure.
2 CHANNEL, FIXED LINE-OUTPUT CONVERTER
The AX-ALOC10 is designed to convert speaker level
audio to line level audio. This allows for the installa-
tion of line level products such as ampliers, EQs and
crossovers on systems that do not have RCA line level
outputs.
Features:
30 Watts Maximum Input, 6:1 Step Down with Fixed
Outputs, Gold Flashed RCAs, Attractive & Durable
Enclosure.
2 CHANNEL, FIXED LINE-OUTPUT CONVERTER
The AX-ALOC10 is designed to convert speaker level
audio to line level audio. This allows for the installa-
tion of line level products such as ampliers, EQs and
crossovers on systems that do not have RCA line level
outputs.
Features:
30 Watts Maximum Input, 6:1 Step Down with Fixed
Outputs, Gold Flashed RCAs, Attractive & Durable
Enclosure.
2 CHANNEL, FIXED LINE-OUTPUT CONVERTER
The AX-ALOC10 is designed to convert speaker level
audio to line level audio. This allows for the installa-
tion of line level products such as ampliers, EQs and
crossovers on systems that do not have RCA line level
outputs.
Features:
30 Watts Maximum Input, 6:1 Step Down with Fixed
Outputs, Gold Flashed RCAs, Attractive & Durable
Enclosure.
2 CHANNEL, FIXED LINE-OUTPUT CONVERTER
/