Salter Labs 7100 Operating instructions

Type
Operating instructions

Salter Labs 7100 is a disposable, single-patient-use device for use in healthcare facilities and home care. The humidifier is used to provide additional humidity to supplemental oxygen therapy. It is available with either a 3 PSI or 6 PSI safety pop-off valve. The humidifier can be used with a flowmeter, concentrator, or liquid tank. It has a maximum water level marking and a minimum water level marking. The humidifier should be washed with warm soapy water every 14 days and rinsed thoroughly with distilled or boiled water. It is recommended to replace the humidifier every 30 days.

Salter Labs 7100 is a disposable, single-patient-use device for use in healthcare facilities and home care. The humidifier is used to provide additional humidity to supplemental oxygen therapy. It is available with either a 3 PSI or 6 PSI safety pop-off valve. The humidifier can be used with a flowmeter, concentrator, or liquid tank. It has a maximum water level marking and a minimum water level marking. The humidifier should be washed with warm soapy water every 14 days and rinsed thoroughly with distilled or boiled water. It is recommended to replace the humidifier every 30 days.

Home
Use
Bubble Humidifier Instructions for Use
and Cleaning Instructions
Instructions for Use
1. Wash hands and remove bubble humidier from package.
2. Unscrew lid and add water to the Maximum Level marking
on the side of the bottle. Sterile, distilled or boiled water is
recommended.
3. Replace lid and ensure lid is screwed on tight.
4. Attach bubble humidier to oxygen source, i.e. owmeter,
concentrator, liquid tank.
5. Test for leaks (A). Turn the ow to 6 LPM and block the
outlet port on the bubble humidier. An alarm should sound in
5 seconds or less. If not, check connections.
6. Attach oxygen tubing to the outlet port (B) and adjust ow to
prescribed setting.
7. Apply interface, i.e. nasal cannula or oxygen mask, to patient.
8. If water level drops to Minimum level marking on bottle, add
more water.
The Bubble Humidifier is a disposable, single-patient
use device for use in health care facilities and home care.
The humidifier is used to provide additional humidity to
supplemental oxygen therapy and is available with either a
3 PSI or 6 PSI safety pop-off valve.
7100 Bubble Humidifier- 3 PSI Pop-off | 7600 Bubble Humidifier- 6 PSI Pop-off
MAXIMUM
Pressure
relief alarm
Pressure
relief port
Maximum
water level
Minimum
water level
Diffuser
Oxygen
outlet port
MINIMUM
Oxygen source
O
2
Source
MAXIMUM
MINIMUM
(A)
MAXIMUM
MINIMUM
Oxygen
Tubing
To
Patient
O
2
Source
(B)
Cleaning Instructions
9. Every 14 days, wash your bubble humidier with warm
soapy water.
10. Rinse thoroughly with distilled or boiled water.
11. Recommend replacing Bubble Humidier every 30 days.
Note Tap Water Use: If using Tap Water in your bubble
humidier or rinsing with Tap Water aer cleaning, wash the
bubble humidier every 3 days.
Final Setup
The Bubble Humidifier is a disposable, single-patient use device for
use in health care facilities and home care.”
Bubble Humidifier Instructions for Use and Cleaning
Instructions (continued)
Your setup may vary slightly depending on what system you use for your oxygen source.
SLML-110 Rev A 042014
  • Page 1 1
  • Page 2 2

Salter Labs 7100 Operating instructions

Type
Operating instructions

Salter Labs 7100 is a disposable, single-patient-use device for use in healthcare facilities and home care. The humidifier is used to provide additional humidity to supplemental oxygen therapy. It is available with either a 3 PSI or 6 PSI safety pop-off valve. The humidifier can be used with a flowmeter, concentrator, or liquid tank. It has a maximum water level marking and a minimum water level marking. The humidifier should be washed with warm soapy water every 14 days and rinsed thoroughly with distilled or boiled water. It is recommended to replace the humidifier every 30 days.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI