Star Trac E Series Stepper E-ST Owner's manual

Brand: Star Trac

Model: E Series Stepper E-ST

Type: Owner's manual

620-7862 C

Page 1 of 7

STAR TRAC FITNESS™

E-SERIES INTEGRATED WIRELESS

RECEIVER KIT

OPERA T I ON MA N UA L

620-7862 C

Page 2 of 7

REGULATORY INFORMATION

FCC

When used in conjunction with the appropriate Star Trac cardio equipment, The MYE WIRELESS RECEIVER HAS

been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC rules.

Under the FCC guidelines, operation is subject to the following two guidelines: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

EUROPEAN DIRECTIVES

This product, when used in conjunction with the approved cardio equipment, conforms to the requirements of

the European Council directives:

 89/336/ECC, Electromagnetic Compatibility

 92/590/EEC, General Product Safety Directives

 73/23/EEC, Electrical equipment Low Voltage Safety Directive

620-7862 C

Page 3 of 7

INTRODUCTION

The MYE ST-C9 (900 MHz) / ST-C8 (800 MHz) Wireless Receiver allows users to listen to a variety of

wall mounted TV’s connected to 900/800MHz Transmitters.

CONTROL BUTTONS

POWER BUTTON

Turns Main Console ON/OFF

UP/DOWN BUTTONS

Wireless Receiver Mode:

Scrolls though programmed TV numbers (preset transmitters)

DISPLAY CHAN Icon illuminates – Channel Number illuminates 1, 2, 3 etc.

TV Icon illuminates

UP/DOWN BUTTONS

Increases or decreased the volume as selected by the user.

DISPLAY Bar graph depicting volume level in all modes

Note- Volume will default to mid-low level after user unplugs headphone.

HIDDEN KEY under

the MYE logo

620-7862 C

Page 4 of 7

EQ BUTTON

Allows the user to scroll between preset equalizer tones. Each time the button is pressed a new EQ

name will light up (the previous will disappear).

DISPLAY EQ Icon always illuminated

Flat, Bass illuminated one at a time

MUTE BUTTON

When the button is pressed the first time the audio MUTES. Pressed a second time turns Mute OFF

and audio comes back ON.

DISPLAY Mute Icon appears when turned ON

Mute Icon disappears when MUTE is OFF

LCD INFORMATION

VOLUME

LEVEL

INDICATOR

CHANNEL

ICON

CURRENT

CHANNEL

MUTE “ON”

FREQUENCY

DETECTED IN

AUTO PROGRAM

MODE

EQ PRESETS

620-7862 C

Page 5 of 7

SET UP INSTRUCTIONS

Transmitter PROGRAMMING MODES (900MHz Version)

During installation the controller must be programmed to lock the TV transmitters. The product is

backwards compatible with all other brands of transmitters so there will be a total of five different

programming modes. In each mode the receiver will automatically scroll through the frequency

bandwidth and “lock-in” the transmitters. Due to spurious emissions and possible missed transmitters,

a manual mode that enables the installer to select individual transmitter channels (each channel is a

designated frequency) and “lock” or “erase” any given channel is also provided.

NOTE: 863MHz version will only have three program modes P-1 for MYE and P-2 for Enercise /

Cardio Theater and P-3 to Audeon.

1: To enter transmitter program mode: Press CHANNEL DOWN and VOLUME UP buttons

simultaneously for three seconds. After three seconds the unit will enter program mode.

DISPLAY- “P-1” will pop up on the display after 3 seconds.

2: To select program mode press CH “+” to select one of the program modes.

DISPLAY (900MHz) P-1, P-2, P-3, P-4, P-5

P-1 = MYE Entertainment Transmitter Mode

P-2 = Cardio Theater LCS Mode

P-3 = Cardio Theater / Enercise xTV Mode

P-4 = BroadcastVision Mode Series 1

P-5 = BroadcastVision Mode Series 2

DISPLAY (863MHz) P-1, P-2, P-3

P-1 = MYE Entertainment 800MHz Transmitter Mode

P-2 = Cardio Theater 800 / Enercise 800

P-3 = Audeon 800

3: To automatically scan and “lock-in” transmitters press the HIDDEN KEY under the MYE logo.

DISPLAY- will show transmitter numbers being scanned in order of frequencies (1, 2, and 3, etc., up

to 32 or 52 for the 900MHz). The total number of channels will correspond to the program mode

selected.

When Scan is complete the controller will default to the first transmitter channel that was found.

DISPLAY- PRESET ICON illuminates

CHAN Icon illuminates

TV (transmitter) Number illuminates

Note: the auto scan may be skipped and the installer may go directly to the manual scan (step 4) by

pressing the EQ button instead of pressing the HIDDEN KEY under the MYE logo.

4: The installer may now scroll through all channels to determine if a transmitter was missed or a

spurious emission was picked up. Then “add or delete” a specific transmitter number.

Press CHANNEL UP/DOWN buttons to scroll through all TV (transmitter) numbers within the specified

transmitter mode. Example: Cardio Theater xTV Mode will scroll through a total of 32 channels (each

channel directly relates to a specific frequency).

DISPLAY- PRESET Icon will appear when a specific transmitter channel is programmed. When a

particular transmitter channel is not programmed the PRESET Icon will not appear.

620-7862 C

Page 6 of 7

To Add or Delete a specific transmitter channel press the HIDDEN KEY under the MYE logo. Each

time the button is pressed it will add or delete a transmitter channel.

DISPLAY- the PRESET ICON “ON” or “OFF” signifies transmitter channel is added or deleted.

5: To exit program mode press “EQ” button. The display will blank briefly and the unit will default to

first transmitter channel programmed.

DISPLAY- TV Icon illuminates

CHAN Icon illuminates

TV number illuminates

Important Note Regarding Transmitter Channel Program Modes:

The Enercise/Cardio Theater Transmitter Frequency Chart have been provided below for reference.

You will note that the frequencies are set in a particular order starting at number 1 through 32. In most

cased the installers will connect the first transmitter to the first TV and set it to #1. They will move

forward to TV number 2 setting transmitter to #2 and so on. There are instances where a particular

frequency is not performing correctly due to various reasons (spurious emissions, interference from

other sources etc.). So as an example if the installer is at TV 4 but Transmitter channel #4 is not

performing, the installer simply moves to the next Transmitters channel, in this case #5, he/she will

then continue on from there. So in essence a typical 5 TV installation may look like this:

TV-1 / Transmitter Channel #1

TV-2 / Transmitter Channel #2

TV-3 / Transmitter Channel #3

TV-4 / Transmitter Channel #5*

TV-5 / Transmitter Channel #6

In this case we had to skip Transmitter channel #4 due to a problem.

However regardless of the Transmitter channels added or deleted, we must always show the actual

TV numbers in correct sequence. In the case above the wall mounted TV’s will have number signs

under each TV starting at 1 and ending with 5. This is the same method used in our last

Enercise/Cardio Theater software.

Frequency

905

905.6

906.2

906.6

923.6

907.6

924.4

908.8

925.6

910

910.6

911.2

911.8

912.4

913.4

913.8

914.2

915

915.4

916.2

917

917.4

917.8

918.4

919

919.6

920.6

921

921.4

921.8

922.6

923

620-7862 C

Page 7 of 7

TROUBLESHOOTING:

RECEPTION RANGE

To change the controller reception to Near/Far, make sure the controller off. Press and hold down the

VOLUME UP button, then press and release the POWER button. Continue holding the VOLUME UP

button for three seconds until ‘LO’ is displayed on the console. This configures the Controller for

“Near” reception. If this procedure is repeated, the display will indicate ‘HI’ and the Controller will be

configured for “Far” reception. The factory default setting is “Far”.

Star Trac E Series Stepper E-ST Owner's manual

Star Trac E Series Stepper E-ST Owner's manual

Star Trac E Series Stepper E-ST Owner's manual

Related papers

Other documents