Campomatic FRZ360N Owner's manual

GB

ENGLISH

Installation, use and maintenance instructions

GB

2

913

STANDARDS-WARNINGS AND RECOMMENDATIONS

Thank you for purchasing one of our appliances.

Please read these notes thoroughly as they have been written to help you obtain the maximum performance

from the appliance.

The quality of the appliance is guaranteed as each one of our products is fully tested as it comes off the

production line.

Use the appliance and you will see just how much satisfaction you will get.

This product complies with current European safety standards governing electrical appliances.

It has been subjected to thorough and meticulous testing to assess its safety and reliability.

Before using the appliance, read this manual carefully as it will tell you what to do and what not to do.

Improper use of the appliance can be dangerous, above all for children.

Before connecting the appliance, make sure that the data on the rating plate complies with that of the domestic

supply.

Do not dispose of the recyclable packing materials in an unauthorised manner.

Take them to an appropriate plant for recycling.

The electrical safety of this appliance is only guaranteed when it has been connected to a mains supply with an

efﬁ cient earthing system as provided for by law.

Mod. A Mod. B

GB

3

913

STANDARDS-WARNINGS AND RECOMMENDATIONS

This is an important safety requirement and must be complied with.

In case of doubt, have the mains supply checked by a qualiﬁ ed electrician.

As with any other electrical appliance, a few fundamental rules must be observed during use:

• do not touch the appliance with wet or damp hands or feet.

• do not pull the power cable to remove the plug from its socket.

• do not expose the appliance to atmospheric agents.

• do not allow the appliance to be used by unsupervised children.

• do not plug-in or unplug the appliance using wet hands. - before carrying out any cleaning or maintenance

operation, disconnect the appliance from the mains supply by either unplugging it or switching the mains power

supply off at the main switch:

• in the case of a fault or malfunction, switch off the appliance and do not attempt any repairs.

This appliance is marked as complying with European Directive 2002/96/EC, Waste Electrical and Electronic

Equipment (WEEE).

Make sure that the product is disposed of in a correct manner. The user is obliged to contribute towards preventing

any negative consequences for health and the environment.

The symbol afﬁ xed to the product or accompanying documents signiﬁ es that the product must not be treated

as normal domestic refuse, but must be delivered to an authorised collection centre to enable the electric and

electronic equipment to be recycled.

Mod. A Mod. B

GB

4

913

STANDARDS-WARNINGS AND RECOMMENDATIONS

When disposing of the appliance, comply with local waste disposal regulations. For further information on the

treatment, recovery and recycling of this product, refer to the appropriate ofﬁ ces, local domestic waste collection

service or the retailer from where the appliance was purchased.

WARNING! At the end of the useful life of an appliance that makes use of R 600a refrigeration gas (isobu-

tane) and ﬂ ammable gas in the insulation foam, it must be made safe prior to being transported to the

place of disposal. To do this, refer to the retailer or the appropriate local authority.

WARNING! When installing the appliance, consideration must be given to the climatic category of the

product itself. The climatic category of the appliance is written on the rating plate. The appliance will

function correctly within the ambient temperature range in the table for the particular climatic category.

WARNING! Make sure that the ventilation openings in the appliance body or built-in units are not ob-

structed.

WARNING! if the appliance is to be left unused for a long period of time, e.g. holidays, it must be unplugged,

emptied, cleaned and dried. The door must be left open to prevent the formation of bad smells.

WARNING: Do not damage the cooling circuit.

GB

5

913

DESCRIPTION OF THE APPLIANCE

Upright units are large capacity domestic appliances for freezing, storing and refrigerating any types of food.

The load-bearing STRUCTURE has been fabricated in steel panels which have been treated and electrostatically

painted to resist mistreatment and to ensure that its “new” look remains unaltered over time. The INSULATION

MATERIALS have been specially selected to ensure that the INTERNAL temperature remains constant and to pro-

vide maximum storage space. The internal STORAGE SPACE has been designed to store any type of food thanks

to the easily removable shelves.

1 CONTROL PANEL

2 FREEZER DRAWERS

3 FREEZER DRAWERS

4 NO-FROST VENTILATION

5 INSTRUCTION BOOK

6 ICE TRAY

7 SPACERS

8 HINGE

9 PLINTH COVER PLATE

5

6

8

9

7

1

2

3

4

1

2

3

4

Mod. A

Mod. B

GB

6

913

REMOVING THE TRANSPORT PROTECTION DEVICES

Check that the appliance is undamaged.

The retailer must be informed of any damage to the appliance within 24 hours of delivery.

1 Remove the protection from the door gasket.

The protection is used to protect the gasket during transport.

The protection must be removed in order to ensure that the door seal functions correctly.

1

GB

7

913

POSITIONING AND INSTALLING THE APPLIANCE

2b

2a

2c

2b2

2d

1 Once the appliance has been unpacked, check that the mains voltage is the same as that indicated on the rating

plate.

2 If the door opening direction is as required, go to Point

3 Otherwise, reverse the position of the hinges.

To do this, carefully place the appliance on its back. Use spacers to prevent crushing the condenser pipes and

damaging the compressor unit.

2a Remove the plinth by pulling it.

2b Remove the lower hinge and unscrew pin (A).

2c Remove the door by pulling downwards.

2d Unscrew the upper pin and screw it in on the opposite side.

A

2b3

GB

8

913

POSITIONING AND INSTALLING THE APPLIANCE

2e Replace the door.

2f Fit the pin from the lower hinge onto that supplied, then ﬁ t the hinge and tighten the door.

2g Replace the hole plugs in the plinth with those supplied.

2h Replace the plinth by pushing it.

REVERSING THE VERTICAL HANDLE

If the appliance is delivered with the vertical handle already ﬁ tted and the door opening direction needs to be

changed, the handle itself must also be moved as follows:

2i Remove the handle by unscrewing the two ﬁ xing screws.

2l Remove the hole plugs on the opposite side of the door by pressing them lightly.

2m Rotate the handle 180° and ﬁ t it in place using the two ﬁ xing screws. Insert the plugs in the holes left on the

opposite side.

FITTING THE VERTICAL HANDLE

If the appliance is supplied with a separate vertical handle, it can be ﬁ tted as follows:

2i Take the handle and screws supplied.

2i Position the handle over the holes and ﬁ x it in position using the screws supplied.

2e

2g

2n

2h

2p

2f

GB

9

913

3 Level the fridge by adjusting the feet.

When installing the appliance, remember the following:

A Do not install it near to sources of heat such as heaters, radiators, cookers, etc. or in direct sunlight.

B Position the appliance in a dry well-ventilated location.

C Do not install the appliance in non-ventilated spaces such as wall niches.

D After the appliance has been placed in its ﬁ nal position, leave it for about an hour before connecting it to the

power supply.

E Make sure that the appliance is working properly before placing any food in it.

F Leave a space of at least 5 cm between the top of the appliance and any wall cupboards.

G Some appliances are ﬁ tted with rear wheels to enable them to be moved easily.

WARNING: DO NOT INSTALL THE APPLIANCE NEAR TO ANY HEAT SOURCES AND LEAVE A GAP OF AT LEAST

5 CM ABOVE IT

POSITIONING AND INSTALLING THE APPLIANCE

3

I

GB

10

913

ELECTRICAL CONNECTION

Check that the mains voltage complies with that indicated on the rating plate located on the bottom left of the

freezer compartment.

If the mains socket does not have an earth connection or if the plug is not suitable for the mains supply system,

refer to a qualiﬁ ed electrician.

Do not use adapters or extension leads, as these may overheat and burn.

Warning: this appliance must be earthed

If the appliance has been ﬁ tted with a non-rewirable plug of the incorrect type for the mains socket, cut off the

plug and ﬁ t a new one. The removed plug must be thrown away. Inserting an unsuitable plug into a 13 Amp socket

is likely to cause an electrical hazard. When a non rewirable plug or rewirable 13 Amp (BS1363) plug is used, it

must be ﬁ tted with a 15 Amp ASTA approved (BS1362) fuse. If any other type of plug is used it must be wired

as follows.

Connect the GREEN & YELLOW wire to the earth terminal marked with the letter “E” or earth symbol, or col-

oured green or green & yellow.

Connect the BLUE wire to the neutral terminal marked with the letter “N” or coloured black.

Connect the BROWN coloured wire to the live terminal marked with the letter “L” or coloured red.

Green and

Yellow to Earth

Blue to

Neutral

13 amp Fuse

Brown

to Live

Cord

Clamp

GB

11

913

DESCRIPTION OF THE CONTROL PANEL

Figure 1 shows the Display in normal position, while ﬁ gure 2 shows the active position

T1 “ECO” BUTTON

T2 “ALARM-RESET” BUTTON

T3 “SUPER” BUTTON

T4 “FREEZER TEMPERATURE CONTROL” BUTTON

S1 “ECO” SYMBOL

S2 “DOOR OPEN AUDIBLE ALARM-RESET” BUTTON

S3 “SUPER” SYMBOL

S4 DOOR SYMBOL

S5 SYMBOL INDICATING:

- ACTUAL INTERNAL TEMPERATURE

- PROGRAMMED TEMPERATURE

- FRIDGE “OFF”

USING THE COMPARTMENT

The temperature inside the compartment is regulated automatically by an electronic system according to that set

by the user. The temperature must be set taking into account the frequency of the door opening, the quantity of

food on the shelves and the ambient temperature.

WARNING: If the appliance is switched off then back on again immediately, the compressor will start-up

after approximately half an hour. This is part of the normal operation of the appliance

USING THE FREEZER COMPARTMENT Mod. A

S1 S2 S3 S4 S5

T1 T2 T3 T4

Fig.1

Fig.2

GB

12

913

SWITCHING ON THE APPLIANCE

Close the door, insert the plug in the mains socket and set the required temperature. Allow the fridge to run empty

until the set temperature appears on the display, then place the food in the compartment and close the door.

T4 SETTING THE TEMPERATURE

To start the appliance, press button “T4” for at least 0.5 seconds To stop the appliance, press button “T4” for 4

seconds. The symbol “—” (ﬁ g. a) will appear on the display. During normal operation, the display will indicate

the internal temperature with the symbol “S5” (ﬁ g. b). The display indicates the values of the internal temperature

between +20°C and -40°C. Temperatures higher than +20°C (e.g. +21°C) are indicated by the letter “H” (ﬁ g. c).

The temperature can be set between -18 and -24 °C.

PROGRAMMING AND ADJUSTING THE TEMPERATURE

Press button “T4” once. The programmed temperature will ﬂ ash for 6 seconds (ﬁ g. d). When button “T4” is re-pressed,

the temperature setting changes. The temperature reduces by 1°C for each clock down to -24°C, after which the display

restarts from -18°C. The new setting will be memorised after “S5” stops ﬂ ashing.

CHECKING THE PROGRAMMED TEMPERATURE

Press button “T4” once. The programmed temperature “S5” will ﬂ ash for 6 seconds (ﬁ g. d), after which the actual

temperature inside the compartment will be displayed. The programmed functions will stay in the memory even in the

case of a power cut or when the appliance is disconnected from the mains supply

USING THE FREEZER COMPARTMENT Mod. A

T4

S5

Fig.a

Fig.b

Fig.c

Fig.d

T4

S5

GB

13

913

USING THE FREEZER COMPARTMENT Mod. A

Fig.e

Fig.f

T3

S3

T3

S3

T1

S1

T1

S1

Fig.g Fig.h

S5

T2

S2

“SUPER” FUNCTION “S3”

The “SUPER” function is used for quick freezing of food and must be activated at least 3 hours before placing

the food in the freezer.

The compressor will function continuously for “28 hours”. When button “T3” is pressed, the symbol “S3”

lights up. The “SUPER” function switches off automatically after 28 hours. It can also be switched off manually at

any time by re-pressing button “T3” (ﬁ g. e).

“ECO” S1 FUNCTION

In order to save energy, the freezer is equipped with a button “T1” “ECO” which automatically sets the temperature

at -18°C and lights up the symbol “S1” (ﬁ g. f). To switch off the “ECO” function, press button “T1”. The

symbol will disappear from the display (ﬁ g. a).

“HIGH TEMPERATURE ALARM” FUNCTION

This appliance is ﬁ tted with a dual alarm system (pre-alarm and alarm).

Pre-alarm (-11°C) If the temperature inside the freezer rises and reaches -11°C, the value on the display ﬂ ashes

(visual alarm) (ﬁ g. g).

Alarm If the temperature inside the freezer rises to above +1°C (the food will start to thaw), the background of

the display will change to red, the symbol “ ” will be displayed (see “S2”, ﬁ g. h) and the highest temperature

value reached by the food will ﬂ ash. This alarm will be memorised even in the case of an interruption in the power

supply. To restart the appliance, press the “RESET” button (ﬁ g. h).

GB

14

913

IMPORTANT

- If the Alarm is activated (red background on the display), the food should be consumed immediately.

If it is not possible to determine the precise time that the food started thawing, it is advisable to throw away all

the food kept in the freezer in order to avoid any health risks.

- Under no circumstance should food that has started to thaw be refrozen.

- Do not store frozen food for longer than the recommended time period.

Possible causes

- An excessive amount of food has been placed in the freezer (see freezing method)

- The door has been left open

- There is a power cut

- The appliance is faulty

USING THE FREEZER COMPARTMENT Mod. A

Fig.h

T2

S2

GB

15

913

DOOR OPEN ALARM AND RESET FUNCTION “S4-S2”

Opening the door activates both the audible alarm RESET “S2” and the door open symbol on the display

“S2” “S4”. 40 seconds after the door has been opened, the door open alarm is activated. The alarm can be silenced

either by pressing the RESET button (ﬁ g. i) for 0.5 seconds, or by closing the door. To deactivate symbol “S4”,

close the door.

FREEZING FRESH FOOD

The freezer has two distinct compartments:

-

The upper compartments “A” are used for freezing fresh food.

-

The lower drawers are used exclusively for storing frozen food.

-

For optimum freezing, the quick-freeze function must be activated at least 3 hours before placing the food in

the freezer.

Prepare the food to be frozen in small portions (max 1 kg). Wrap the food in purpose-made polythene or aluminium

foil, if possible airtight. Make a note of the date of freezing on the wrap and place it in the freezer drawer.

To make freezing easier and more efﬁ cient, follow the recommendations given below:

- The maximum quantity of fresh food to freeze is reported in kg/24 hrs on the rating plate inside the fridge located on the

left alongside the fruit and veg box.

- Divide the food to be frozen into small portions for ease of freezing and eventual thawing.

- Do not place fresh foods to be frozen in direct contact with already frozen foods as this may cause a rise in tem-

perature in the already frozen product.

USING THE FREEZER COMPARTMENT Mod. A

A

Fig.i

S2

S4

S2

S4

T2

GB

16

913

DESCRIPTION OF THE CONTROL PANEL

Figure 1 shows the Display in normal position, while ﬁ gure 2 shows the active position

T1 “ECO” BUTTON

T2 “SUPER” BUTTON

T3 “FREEZER TEMPERATURE CONTROL” BUTTON

S1 “ECO” SYMBOL

S2 “SUPER” SYMBOL

S3 DOOR SYMBOL

S4 SYMBOL INDICATING:

- ACTUAL INTERNAL TEMPERATURE

- PROGRAMMED TEMPERATURE

- FRIDGE “OFF”

USING THE COMPARTMENT

The temperature inside the compartment is regulated automatically by an electronic system according to that set

by the user. The temperature must be set taking into account the frequency of the door opening, the quantity of

food on the shelves and the ambient temperature.

WARNING: If the appliance is switched off then back on again immediately, the compressor will start-up

after approximately half an hour. This is part of the normal operation of the appliance

USING THE FREEZER COMPARTMENT Mod. B

T2 T3T1

S1

S2

S3-S4

Fig. 2

Fig. 1

GB

17

913

SWITCHING ON THE APPLIANCE

Close the door, insert the plug in the mains socket and set the required temperature. Allow the fridge to run empty

until the set temperature appears on the display, then place the food in the compartment and close the door.

T3 SETTING THE TEMPERATURE

To start the appliance, press button “T3” for at least 0.5 seconds To stop the appliance, press button “T3” for 4

seconds. The symbol “—” (ﬁ g. a) will appear on the display. During normal operation, the display will indicate

the internal temperature with the symbol “S3” (ﬁ g. b). The display indicates the values of the internal temperature

between +20°C and -40°C. Temperatures higher than +20°C (e.g. +21°C) are indicated by the letter “H” (ﬁ g. c).

The temperature can be set between -18 and -24 °C.

PROGRAMMING AND ADJUSTING THE TEMPERATURE

Press button “T3” once. The programmed temperature will ﬂ ash for 6 seconds (ﬁ g. d). When button “T3” is re-pressed,

the temperature setting changes. The temperature reduces by 1°C for each clock down to -24°C, after which the display

restarts from -18°C. The new setting will be memorised after “S3” stops ﬂ ashing.

CHECKING THE PROGRAMMED TEMPERATURE

Press button “T3” once. The programmed temperature “S3” will ﬂ ash for 6 seconds (ﬁ g. d), after which the actual

temperature inside the compartment will be displayed. The programmed functions will stay in the memory even in the

case of a power cut or when the appliance is disconnected from the mains supply

USING THE FREEZER COMPARTMENT Mod. B

T3

S3

Fig.a

Fig.b

Fig.c

Fig.d

T3

S3

GB

18

913

“SUPER” FUNCTION “S2”

The “SUPER” function is used for quick freezing of food and must be activated at least 3 hours before placing

the food in the freezer. The compressor will function continuously for “28 hours”. When button “T2” is pressed,

the symbol “S2” lights up. The “SUPER” function switches off automatically after 28 hours. It can also be

switched off manually at any time by re-pressing button “T2” (ﬁ g. e).

TEMPERATURE ALARM FUNCTION

The temperature alarm is activated when the temperature inside the freezer compartment is higher than -12°C

(e.g. -11) and is signalled by the ﬂ ashing display (ﬁ g. g).

Possible causes

-

An excessive amount of food has been placed in the freezer (see freezing method)

- The door has been left open

- There is a power cut

- The frost layer has reached a thickness of 3-4 millimetres (see defrosting)

- The appliance is faulty

“ECO” S1 FUNCTION

In order to save energy, the freezer is equipped with a button “T1” “ECO” which automatically sets the temperature at

-18°C and lights up the symbol “S1” (ﬁ g. f). To switch off the “ECO” function, press button “T1”. The symbol

will disappear from the display (ﬁ g. a).The ECO and Super functions cannot be used at the same time

USING THE FREEZER COMPARTMENT Mod. B

Fig.e

Fig.f

Fig.g

T2

S2

T2

S2

T1

S1

T1

S1

S3

GB

19

913

“S3” DOOR OPEN ALARM FUNCTION

Once the door has been opened for 10 seconds, the “ “ symbol runs across the display (ﬁ g. h). 40 seconds

after the door has been opened, the audible door open alarm will sound: both the display and audible alarm will

cease once the door has been closed.

FREEZING FRESH FOOD

The freezer has two distinct compartments:

-

The upper compartments “A” are used for freezing fresh food.

-

The lower drawers are used exclusively for storing frozen food.

-

For optimum freezing, the quick-freeze function must be activated at least 3 hours before placing the food in

the freezer.

Prepare the food to be frozen in small portions (max 1 kg). Wrap the food in purpose-made polythene or aluminium

foil, if possible airtight. Make a note of the date of freezing on the wrap and place it in the freezer drawer.

To make freezing easier and more efﬁ cient, follow the recommendations given below:

- The maximum quantity of fresh food to freeze is reported in kg/24 hrs on the rating plate inside the fridge located

on the left alongside the fruit and veg box.

- Divide the food to be frozen into small portions for ease of freezing and eventual thawing.

- Do not place fresh foods to be frozen in direct contact with already frozen foods as this may cause a rise in tem-

perature in the already frozen product.

USING THE FREEZER COMPARTMENT Mod. B

A

Fig.h

S3

GB

20

913

RECOMMENDATIONS:

NEVER place ice cubes in the mouth or eat ice-lollies that have just been taken out of the freezer, as these can

cause ice burns.

DO NOT place sealed containers containing liquids such as soft-drinks or similar in the freezer.

Hot foods and drinks must be allowed to cool before being placed in the freezer.

STORING FROZEN FOOD

It is impossible to accurately predict the effective storage period for frozen food in that this varies considerably

according to the nature of the food itself.

To be safe, always follow the instructions reported on the packaging of frozen food products.

ICE-CUBE PRODUCTION

Fill the ice-tray 3/4 full with water. Place it in the sliding drawer (where ﬁ tted) in the freezer compartment.

GENERAL ADVICE:

Make sure that the packaging is intact and that there are no damp marks or swelling, in that these indicate that

the frozen product may already have deteriorated.

Any food that has started to thaw out must not under any circumstances be re-frozen.

Do not store frozen foods for longer than the recommended time period.

USING THE FREEZER COMPARTMENT

Page is loading ...

Campomatic FRZ360N Owner's manual

This manual is also suitable for

Campomatic FRZ360N Owner's manual

Related papers

Other documents