Viking Range P30CBF4SS Installation guide

Brand: Viking Range

Model: P30CBF4SS

Type: Installation guide

Installation Guide

Range/Rangetop Rear Island Trim / Backguard / High Shelf Accessories

Range Curb Base Fronts

Rear Trim Accessories

MODELS BACKGUARD HIGH SHELF CURB BASE

C/VGCC530

C/VDSC530

C/VESC530

C/VISC530

C/VGRT530

P30BG8SS

B30HS24SS P30CBF4SS

C/VGCC536

C/VDSC536

C/VGRT536

P36BG8SS B36HS24SS P36CBF4SS

C/VGCC548

C/VDSC548

C/VGRT548

P48BG8SS B48HS24SS P48CBF4SS

C/VGCC560

C/VDSC560

C/VGRT530

P601BG8SS B60HS24SS P60CBF4SS

C/RVGR3301

C/RVDR3301

C/RVER3301

RD301BG6SS

N/A

P30CBF4SS

(Illustration II)

Grasp the trim on each end and carefully place in the channels (B) located at each rear corner of the

product. Align the screw holes (A) at each end of the trim device with the holes (A) in each rear channel

of the product. Secure with the 4 enclosed screws.

RANGETOP

REAR VIEW

RANGE REAR

VIEW

(Illustration I)

HIGH SHELF

Rear Trim Accessories

ATTACHING REAR TRIM (Illustration I)

ATTACHING SHELF ON HIGH-SHELF (Illustration II)

All rear trim devices are installed in the same basic way.

Place the top rolled edge (X) over the front lip of the high-shelf back trim and secure with the 4

enclosed screws, two at each end.

WARNING

To reduce the risk of fire or injury to

persons, check to make sure all packaging

has been removed from the outside and

inside parts of the rear trim device before

installing. MAKE SURE ALL CORRUGATED

MATERIAL IS REMOVED FROM INSIDE

THE HIGH SHELF.

Once you determine whether or not your product needs the provided spacers, the backguard is ready

to be attached. Simply slide the backguard down onto the rear of the unit behind the spacers and

attach using the (4) screws provided. (See Figure 4)

C/VGCC560 ranges require that two 1” standoff spacers be attached to the back of the range when

using a range with a backguard against a combustible surface. (See Figure 3)

Figure 3

Backguards come equipped with Nylon Spacers (See Figure 1), which are needed to space the

range off a combustible wall a prescribed safe distance.

Note: If the back wall is Non-

Combustible, these spacers can be

removed. (See Figure 2)

These spacers can also be removed if used with any of

the models* listed below:

• C/VGCC530

• C/VDSC530

• C/VDSC536

• C/VGRT530

• C/VGRT536

ATTACHING BACKGUARD (Illustration III)

Figure 1

(Illustration III)

Figure 2

*If you have one of these models, the spacers are not

required, even if with a combustible wall.

Rear Trim Accessories

IMPORTANT: USE OF ISLAND TRIM WITH AND WITHOUT 6” (15.2 CM) CLEARANCE.

Normal installation for island trim on either a range or rangetop is in an island/peninsula or where there is a

minimum clearance of 6”(15.2 cm) to any type of wall at the rear of the unit. Ranges and rangetops with an

island trim installation can be installed at zero clearance to the rear wall as long as the wall is non-combustible.

The responsibility for ensuring that the rear wall is non-combustible and heat resistant lies with the individual

owner and/or end user. Only in those cases where the island trim is installed with 6” (15.2 cm) of minimum

clearance to a rear wall, or when a truly non-combustible material is used, will the warranty apply. In no case will

Viking Range, LLC accept responsibility for any claims which may result from heat damage against a rear wall,

including cosmetic damage. It is the total responsibility of the owner/end user to ensure that the material

utilized in such applications is not only non-combustible, but is also truly heat-resistant.

Figure 4

Rear Trim Accessories

ATTACHING ISLAND TRIM

Curb Bases

Alternate Curb Base View

for Custom Ranges

STANDARD CURB BASE FRONT

1. The standard curb base front (A) is completely assembled.

2. Remove the assembly from the carton and simply clip onto the front range legs.

3. The assembly is adjustable about 2” (5.1 cm) front to back so that alignment with the cabinet

toe front is possible. Loosen brackets on each side, but allow snug fit. Clip assembly onto

range legs; determine front to back setting; remove, tighten bolts, and reattach.

Important Note: The range must be installed as specified in the range installation guide for proper

airflow when using the standard curb base.

CUSTOM CURB BASE FRONT

1. Remove the standard curb base front assembly from the carton.

2. Remove the front (A) from the mounting assembly (B).

3. Attach locally supplied front (C) to the mounting assembly (B) and simply clip onto the front

range legs.

Important Note: The locally supplied front must not be any taller than 3-1/8” (7.9 cm) tall. Fronts taller

than 3-1/8” (7.9 cm) could obstruct the airflow.

4. The assembly is adjustable about 2” (5.1 cm) front to back so that alignment with the cabinet

toe front is possible. Loosen brackets on each side, but allow snug fit. Clip assembly onto

range legs; determine front to back setting; remove, tighten bolts, and reattach.

Curb Bases

Important Note: The range must be installed as specified in the range installation guide for proper

airflow when using the custom curb base.

Viking Range, LLC

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information

call 1-888-845-4641

F1448O EN

(073115)

Viking Range P30CBF4SS Installation guide

Viking Range P30CBF4SS Installation guide

Viking Range P30CBF4SS Installation guide

Related papers

Other documents