NAPOLEON NC19-24F-I-B User manual

CS78421-548-754

IMPORTANT NOTE:

Read this manual carefully before installing

or operating your new air conditioning

unit. Make sure to save this manual for

future reference.

SPLIT-TYPE ROOM AIR CONDITIONER

Installation Manual

Aurora Series

All Model Numbers

Table of Contents

Installation Manual

Indoor Unit Installation........ 11

1. Select installation location.......................... 11

2. Attach mounting plate to wall....................

12

3. Drill wall hole for connective piping............

12

4. Prepare refrigerant piping...........................

14

5. Connect drain hose....................................

15

6. Connect signal cable..................................

17

7. Wrap piping and cables..............................

18

8. Mount indoor unit.....................................

18

Outdoor Unit Installation...

20

8

1. Select installation location.................. 20

2. Install drain joint................................

21

3. Anchor outdoor unit..........................

22

4. Connect signal and power cables.......23

Safety Precautions........................... 4

0

1

5

Accessories........................................ 6

2

4

Unit Parts.......................................... 10

3

Installation Summary - Indoor Unit........

Refrigerant Piping Connection........ 25

A. Note on Pipe Length................................................ 25

B. Connection Instructions –Refrigerant Piping............. 25

1. Cut pipe..............................................................

25

2. Remove burrs......................................................

26

3. Flare pipe ends....................................................

26

4. Connect pipes.....................................................

27

Air Evacuation................... 29

1. Evacuation Instructions...................... 29

2. Note on Adding Refrigerant...............30

Electrical and Gas Leak Checks........ 31

Test Run............................................ 32

European Disposal Guidelines........ 34

6

7

8

9

10

MC MC

Impedance Information.................. 35

11

 Page 4 

This symbol indicates that ignoring instructions may cause death or serious

injury.

This symbol indicates that ignoring instructions may cause moderate injury

to your person, or damage to your unit or other property.

Safety Precautions

Read Safety Precautions Before Installation

Incorrect installation due to ignoring instructions can cause serious damage or injury.

The seriousness of potential damage or injuries is classiﬁed as either a WARNING or CAUTION.

WARNING

CAUTION

WARNING

Do not modify the length of the power supply cord or use an extension cord to power the unit.

Do not

share the electrical outlet with other appliances. Improper or insufficient power supply

can cause fire or electrical shock.

When connecting refrigerant piping, do not

let substances or gases other than the specified

refrigerant enter the unit. The presence of other gases or substances will lower the unit’s capacity,

and can cause abnormally high pressure in the refrigeration cycle. This can cause explosion and

injury.

allow children to play with the air conditioner. Children must be supervised around the

unit at all times.

1.

Installation must be performed by an authorized dealer or specialist. Defective installation can

cause water leakage, electrical shock, or fire.

2.

Installation must be performed according to the installation instructions. Improper installation can

cause water leakage, electrical shock, or fire.

In North America,installation must be performed in accordance with the requirement of NEC and

CEC by authorized personnel only.)

3.

Contact an authorized service technician for repair or maintenance of this unit.

4.

Only use the included accessories, parts, and specified parts for installation. Using non-standard

parts can cause water leakage, electrical shock, fire, and can cause the unit to fail.

5.

Install the unit in a firm location that can support the unit’s weight. If the chosen location cannot

support the unit’s weight, or the installation is not done properly, the unit may drop and cause

serious injury and damage.

This symbol indicates that you must never perform the action indicated.

 Page 5 

WARNING

6.

For all electrical work, follow all local and national wiring standards, regulations, and the

Installation Manual. You must use an independent circuit and single outlet to supply power. Do

not connect other appliances to the same outlet. Insufficient electrical capacity or defects in

electrical work can cause electrical shock or fire.

7.

For all electrical work, use the specified cables. Connect cables tightly, and clamp them securely to

prevent external forces from damaging the terminal. Improper electrical connections can overheat

and cause fire, and may also cause shock.

8.

9.

10.

11.

All wiring must be properly arranged to ensure that the control board cover can close properly. If

the control board cover is not closed properly, it can lead to corrosion and cause the connection

points on the terminal to heat up, catch fire, or cause electrical shock.

This appliance can be used by children aged from 8 years and above and persons with reduced

Physical, sensory or mental capabilities or lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

CAUTION

For units that have an auxiliary electric heater, do not install the unit within 1 meter (3 feet) of

any combustible materials.

Do not

install the unit in a location that may be exposed to combustible gas leaks. If combustible

gas accumulates around the unit, it may cause fire.

Do not operate your air conditioner in a wet room such as a bathroom or laundry room. Too

much exposure to water can cause electrical components to short circuit.

1.

The product must be properly grounded at the time of installation, or electrical shock may occur.

2.

Install drainage piping according to the instructions in this manual. Improper drainage may cause

water damage to your home and property.

Note about Fluorinated Gasses

1.

This air-conditioning unit contains ﬂuorinated gasses. For specific information on the type of gas

and the amount, please refer to the relevant label on the unit itself.

2.

Installation, service, maintenance and repair of this unit must be performed by a certiﬁed

technician.

3.

Product uninstallation and recycling must be performed by a certiﬁed technician.

4.

If the system has a leak-detection system installed, it must be checked for leaks at least every 12

months.

5.

When the unit is checked for leaks, proper record-keeping of all checks is strongly

recommended.

In certain functional environments, such as kitchens, server rooms, etc., the use of specially designed

air-conditioning units is highly recommended.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

Name

Shape Quantity

1

(for cooling & heating

models only)

Clip anchor

Mounting plate ﬁxing

screw ST3.9 X 25

Remote controller

Fixing screw for remote

controller holder ST2.9 x 10

Remote controller holder

Dry battery AAA.LR03

Seal

Drain joint

Mounting plate

1

Accessories

The air conditioning system comes with the following accessories. Use all of the installation

parts and accessories to install the air conditioner. Improper installation may result in water

leakage, electrical shock and fire, or cause the equipment to fail.

5

2

1

Optional

Parts

2

 Page 6 

1

Owner’s manual

Installation manual

Remote controller

illustration

SPLIT-TYPE ROOM AIR CONDITIONER

CS78421-548-754

IMPORTANT NOTE:

Read this manual carefully before installing

or operating your new air conditioning

unit. Make sure to save this manual for

future reference.

Owner’s Manual

Aurora Series

All Model Numbers

SPLIT-TYPE ROOM AIR CONDITIONER

CS78421-548-754

IMPORTANT NOTE:

Read this manual carefully before installing

or operating your new air conditioning

unit. Make sure to save this manual for

future reference.

Installation Manual

Aurora Series

All Model Numbers

 Page 7 

Name

Shape Quantity

Parts you must purchase.

Consult the dealer about

the pipe size.

Connecting pipe

assembly

Liquid side

Gas side

Φ

6.35( 1/4 i n)

Φ9.52( 3/8in)

Φ12.7( 1/2in)

Φ 16( 5/8in)

IMPORTANT NOTE:

Read this manual carefully before installing

or operating your new air conditioning

unit. Make sure to save this manual for

future reference.

AIR CO ND I TI ON E R

RE MOT E C ONT R OL LER ILLU STRATI O N

Φ 19( 3/4in)

 Page 8 

Installation Summary - Indoor Unit

2

Installation

Overview

Select Installation Location

(Page 11)

Attach Mounting Plate

(Page 12)

Drill Wall Hole

(Page 12)

Determine Wall Hole Position

(Page 12)

1 2

3 4

12cm

(4.75in)

2.3m (90.55in)

12cm

(4.75in)

15cm (5.9in)

 Page 9 

Installation

Overview

Mount Indoor Unit

(Page 18)

STEP

8

Wrap Piping and Cable

(not applicable for some locations in the US )

(Page 18)

Connect Piping

(Page 25)

Connect Wiring

(Page 17)

Prepare Drain Hose

(Page 14)

5 6 7

8

9

 Page 10 

Unit Parts

3

Installation

Overview

NOTE ON ILLUSTRATIONS

Illustrations in this manual are for explanatory purposes. The actual shape of your indoor

unit may be slightly different. The actual shape shall prevail.

Fig. 2.1

NOTE: The installation must be performed in accordance with the requirement of local and

national standards. The installation may be slightly different in different areas.

Wall Mounting Plate

Power Cable (Some Units)

Refrigerant Piping

Signal Cable

Remote Controller

Drainage Pipe

Louver

Remote controller Holder

(Some Units)

Functional Filter (On Front of

Main Filter - Some Units)

Front Panel

Outdoor Unit Power Cable

(Some Units)

1

2

3

4

5

6

7

8

9

10

11

1 2

1

2

3

4

6

7

8

9

10

11

Air-break switch

3

1

2

4

5

6

7

8

11

5

 Page 11 

Indoor Unit Installation

4

Installation Instructions – Indoor

Unit

PRIOR TO INSTALLATION

Before installing the indoor unit, refer to the

label on the product box to make sure that the

model number of the indoor unit matches the

model number of the outdoor unit.

Step 1: Select installation location

Before installing the indoor unit, you must

choose an appropriate location. The following

are standards that will help you choose an

appropriate location for the unit.

Proper installation locations meet the

following standards:



Good air circulation



Convenient drainage



Noise from the unit will not disturb other

people



Firm and solid—the location will not vibrate



Strong enough to support the weight of the

unit



A location at least one meter from all other

electrical devices (e.g., TV, radio, computer)

DO NOT install unit in the following

locations:

Near any source of heat, steam, or

combustible gas

Near ﬂammable items such as curtains or

clothing

Near any obstacle that might block air

circulation

Near the doorway

In a location subject to direct sunlight

NOTE ABOUT WALL HOLE:

If there is no ﬁxed refrigerant piping:

While choosing a location, be aware that you

should leave ample room for a wall hole (see

Drill wall hole for connective piping step)

for the signal cable and refrigerant piping

that connect the indoor and outdoor units.

The default position for all piping is the right

side of the indoor unit (while facing the unit).

However, the unit can accommodate piping to

both the left and right.

Indoor Unit

Installation

 Page 12 

Refer to the following diagram to ensure proper distance from walls and ceiling:

Step 2: Attach mounting plate to wall

The mounting plate is the device on which you

will mount the indoor unit.

1.

Remove the screw that attaches the mounting

plate to the back of the indoor unit.

2.

Place the mounting plate against the wall

in a location that meets the standards in

the Select Installation Location step. (See

Mounting Plate Dimensions for detailed

information on mounting plate sizes.)

3.

Drill holes for mounting screws in places that:

• have studs and can support the weight of

the unit

• correspond to screw holes in the mounting

plate

4.

Secure the mounting plate to the wall with

the screws provided.

5.

Make sure that mounting plate is flat against

the wall.

NOTE FOR CONCRETE OR BRICK WALLS:

If the wall is made of brick, concrete, or similar

material, drill 5mm-diameter (0.2in-diameter)

holes in the wall and insert the sleeve anchors

provided. Then secure the mounting plate to

the wall by tightening the screws directly into

the clip anchors.

Step 3: Drill wall hole for connective piping

You must drill a hole in the wall for refrigerant

piping, the drainage pipe, and the signal cable

that will connect the indoor and outdoor units.

1.

Determine the location of the wall hole based

on the position of the mounting plate. Refer

to Mounting Plate Dimensions on the

next page to help you determine the optimal

position. The wall hole should have a 65mm

(2.5in) diameter at least, and at a slightly

lower angle to facilitate drainage.

Indoor Unit

Installation

Fig. 3.1

12cm (4.75in)

or more

2.3m (90.55in) or more

12cm (4.75in)

or more

15cm (5.9in) or more

2.

3.

Place the protective wall cuff in the hole. This

protects the edges of the hole and will help

seal it when you finish the installation process.

CAUTION

When drilling the wall hole, make sure to

avoid wires, plumbing, and other sensitive

components.

Using a 65mm (2.5in) or 90mm(3.54in)

(depending on models )core drill, drill a

hole in the wall. Make sure that the hole

is drilled at

a slight downward angle, so

that the outdoor end of the hole is lower

than the indoor end by about 5mm to 7mm

(0.2-0.27in). This will ensure proper water

drainage. (See Fig. 3.2)

 Page 13 

Wall

Indoor Outdoor

mm7-5

(0.2-0.27in)

Fig.3.2

MOUNTING PLATE DIMENSIONS

Different models have different mounting plates.

In order to ensure that you have ample room to

mount the indoor unit, the diagrams to the right

show different types of mounting plates along

with the following dimensions:

•

Width of mounting plate

•

Height of mounting plate

•

Width of indoor unit relative to plate

•

Height of indoor unit relative to plate

•

Recommended position of wall hole (both

to the left and right of mounting plate)

•

Relative distances between screw holes

Indoor Unit

Installation

Fig. 3.2

101mm (4in)

179mm (7.05in)

136mm (5.35in)

37mm (1.45in)

290mm (11.4in)

49mm (1.95in)

Right rear wall

hole 65mm (2.5in)

Indoor unit outline

722mm (28.45in)

49mm (1.95in)

192mm (7.55in)

232mm (9.15in)

426mm (16.8in)

128mm (5.05in)

43mm (1.7in)

297mm (11.7in)

Left rear wall

hole 65mm (2.5in)

Right rear wall

hole 65mm (2.5in)

Indoor unit outline

802mm (31.6in)

43mm (1.7in)

144mm (5.65in)

58mm (2.3in)

319mm (12.55in)

57mm (2.25in)

40mm (1.55in)

Right rear wall

hole 65mm (2.5in)

Model C

965mm (38in)

138mm (5.45in)

34mm (1.35in)

Indoor unit outline

219mm (8.6in)

553mm (21.77in)

300mm (11.8in)

335mm (13.2in)

Left rear wall

hole 65mm (2.5in)

Right rear wall

hole 65mm (2.5in)

Model D

1080mm (42.5in)

53.5mm

(2.1in)

47mm (1.85in)

76mm(3in)

53.5mm (2.1in)

47mm (1.85in)

148.7mm

(5.85in)

151mm (5.95in)

174.3mm (6.85in)

Indoor unit outline

172mm (6.8in)

362mm (14.25in)

Left rear wall

hole 65mm (2.5in)

Right rear wall

hole 65mm (2.5in)

Model E

1259mm (49.55in)

Indoor unit outline

52mm (2.05in)

389mm (15.3in)

332mm (13.05in)

257mm (10.1in)

643.6mm (25.3in)

52mm (2.05in)

Correct orientation of Mounting Plate

517.4mm (20.37in)

348.4mm (13.7in)

Φ

NOTE: When the gas side connective pipe is

16mm(5/8in) or more, the wall hole should

be 90mm(3.54in).

 Page 14 

CAUTION

Be extremely careful not to dent or damage the piping while bending them away from the

unit. Any dents in the piping will affect the unit’s performance.

Step 4: Prepare refrigerant piping

The refrigerant piping is inside an insulating

sleeve attached to the back of the unit. You must

prepare the piping before passing it through the

hole in the wall. Refer to the Refrigerant Piping

Connection section of this manual for detailed

instructions on pipe ﬂaring and ﬂare torque

requirements, technique, etc.

1. Based on the position of the wall hole relative

to the mounting plate, choose the side from

which the piping will exit the unit.

2. If the wall hole is behind the unit, keep the

knock-out panel in place. If the wall hole is to

the side of the indoor unit, remove the plastic

knock-out panel from that side of the unit.

(See Fig. 3.3 ). This will create a slot through

which your piping can exit the unit. Use

needle nose pliers if the plastic panel is too

difficult to remove by hand.

3.

Use scissors to cut down the length of the

insulating sleeve to reveal about 15cm (6in)

of the refrigerant piping. This serves two

purposes:

• To facilitate the Refrigerant Piping

Connection process

• To facilitate Gas Leak Checks and enable

you to check for dents

4.

If existing connective piping is already

embedded in the wall, proceed directly to

the Connect Drain Hose step. If there is no

embedded piping, connect the indoor unit’s

refrigerant piping to the connective piping

that will join the indoor and outdoor units.

Refer to the Refrigerant Piping Connection

section of this manual for detailed instructions.

5.

Based on the position of the wall hole

relative to the mounting plate, determine the

necessary angle of your piping.

6.

Grip the refrigerant piping at the base of the

bend.

7.

Slowly, with even pressure, bend the piping

towards the hole. Do not dent or damage the

piping during the process.

NOTE ON PIPING ANGLE

Refrigerant piping can exit the indoor unit from

four different angles:

•

Left-hand side

•

Left rear

•

Right-hand side

•

Right rear

Refer to

Fig. 3.4 for details.

Fig. 3.3

Fig. 3.4

Indoor Unit

Installation

Knock-out Panel

 Page 15 

Step 5:Connect drain hose

By default, the drain hose is attached to the left-

hand side of unit (when you’re facing the back

of the unit). However, it can also be attached to

the right-hand side.

1.

To ensure proper drainage, attach the drain

hose on the same side that your refrigerant

piping exits the unit.

2.

Attach drain hose extension (purchased

separately) to the end of drain hose.

3.

Wrap the connection point firmly with Teflon

tape to ensure a good seal and to prevent

leaks.

4.

For the portion of the drain hose that will

remain indoors, wrap it with foam pipe

insulation to prevent condensation.

5.

Remove the air ﬁlter and pour a small amount

of water into the drain pan to make sure that

water ﬂows from the unit smoothly.

NOTE ON DRAIN HOSE

PLACEMENT

Make sure to arrange the drain hose

according to

Fig. 3.5.

DO NOT

kink the drain hose.

DO NOT

create a water trap.

DO NOT

put the end of drain hose in

water or a container that will collect

water.

PLUG THE UNUSED DRAIN HOLE

To prevent unwanted leaks you must plug

the unused drain hole with the rubber plug

provided.

CORRECT

Make sure there are no

kinks or dent in drain

hose to ensure proper

drainage.

NOT CORRECT

Kinks in the drain hose

will create water traps.

NOT CORRECT

Do not place the end

of the drain hose in

water or in containers

that collect water. This

will prevent proper

drainage.

NOT CORRECT

Kinks in the drain hose

will create water traps.

Fig. 3.5

Fig. 3.6

Fig. 3.7

Fig. 3.8

Indoor Unit

Installation

 Page 16 

BEFORE PERFORMING ELECTRICAL WORK, READ THESE REGULATIONS

1.

All wiring must comply with local and national electrical codes, and must be installed by a

licensed electrician.

2.

All electrical connections must be made according to the Electrical Connection Diagram

located on the panels of the indoor and outdoor units.

3.

If there is a serious safety issue with the power supply, stop work immediately. Explain your

reasoning to the client, and refuse to install the unit until the safety issue is properly resolved.

4.

Power voltage should be within 90-110% of rated voltage. Insufficient power supply can

cause malfunction, electrical shock, or fire.

5.

If connecting power to fixed wiring, install a surge protector and main power switch with a

capacity of 1.5 times the maximum current of the unit.

6.

If connecting power to fixed wiring, a switch or circuit breaker that disconnects all poles and

has a contact separation of at least 1/8in (3mm) must be incorporated in the fixed wiring. The

qualified technician must use an approved circuit breaker or switch.

7.

Only connect the unit to an individual branch circuit outlet. Do not connect another appliance

to that outlet.

8.

Make sure to properly ground the air conditioner.

9.

Every wire must be firmly connected. Loose wiring can cause the terminal to overheat,

resulting in product malfunction and possible fire.

10.

Do not let wires touch or rest against refrigerant tubing, the compressor, or any moving parts

within the unit.

11.

If the unit has an auxiliary electric heater, it must be installed at least 1 meter (40in) away

from any combustible materials.

Indoor Unit

Installation

WARNING

BEFORE PERFORMING ANY ELECTRICAL OR WIRING WORK, TURN OFF THE MAIN POWER

TO THE SYSTEM.

 Page 17 

Step 6: Connect signal cable

The signal cable enables communication between

the indoor and outdoor units. You must ﬁrst

choose the right cable size before preparing it for

connection.

Cable Types

•

Indoor Power Cable

(if applicable):

H05VV-F or H05V2V2-F

•

Outdoor Power Cable:

H07RN-F

•

Signal Cable: H07RN-F

Minimum Cross-Sectional Area of

Power and Signal Cables

Other Regions

Rated Current of

Appliance (A)

Nominal Cross-Sectional

Area (mm²)

> 3 and ≤ 6 0.75

> 6 and ≤ 10 1

> 10 and ≤ 16 1.5

> 16 and ≤ 25 2.5

> 25 and ≤ 32 4

> 32 and ≤ 40 6

CHOOSE THE RIGHT CABLE SIZE

The size of the power supply cable, signal

cable, fuse, and switch needed is determined

by the maximum current of the unit. The

maximum current is indicated on the nameplate

located on the side panel of the unit. Refer to

this nameplate to choose the right cable, fuse,

or switch.

TAKE NOTE OF FUSE SPECIFICATIONS

The air conditioner’s circuit board (PCB) is

designed with a fuse to provide overcurrent

protection. The speciﬁcations of the fuse

are printed on the circuit board, such as:

T3.15A/250VAC, T5A/250VAC, etc.

1.

Prepare the cable for connection:

a.

Using wire strippers, strip the rubber jacket

from both ends of signal cable to reveal

about 40mm (1.57in) of the wires inside.

b.

Strip the insulation from the ends of the

wires.

c.

Using wire crimper, crimp u-type lugs on

the ends of the wires.

PAY ATTENTION TO LIVE WIRE

While crimping wires, make sure you clearly

distinguish the Live (“L”) Wire from other wires.

2. O

pen front panel of the indoor unit.

3.

Using a screwdriver, open the wire box cover

on the right side of the unit. This will reveal

the terminal block.

Terminal block

Wire cover

Screw

Cable clamp

WARNING

4.

Unscrew the cable clamp below the terminal

block and place it to the side.

5.

Facing the back of the unit, remove the plastic

panel on the bottom left-hand side.

Fig. 3.9

Indoor Unit

Installation

The Wiring Diagram is located

on the inside of the indoor unit’s

wire cover.

North America

Appliance Amps (A)

AWG

10 18

13 16

18 14

25 12

30 10

ALL WIRING MUST PERFORMED STRICTLY

IN ACCORDANCE WITH THE WIRING

DIAGRAM LOCATED ON THE INSIDE OF THE

INDOOR UNIT S WIRE COVER.

’

 Page 18 

6. Feed the signal wire through this slot, from

the back of the unit to the front.

7. Facing the front of the unit, match the wire

colors with the labels on the terminal block,

connect the u-lug and and firmly screw each

wire to its corresponding terminal.

CAUTION

DO NOT MIX UP LIVE AND NULL WIRES

This is dangerous, and can cause the air

conditioning unit to malfunction.

8.

After checking to make sure every connection

is secure, use the cable clamp to fasten the

signal cable to the unit. Screw the cable clamp

down tightly.

9.

Replace the wire cover on the front of the

unit, and the plastic panel on the back.

NOTE ABOUT WIRING

Step 7: Wrap piping and cables

Before passing the piping, drain hose, and the

signal cable through the wall hole, you must

bundle them together to save space, protect

them, and insulate them.

1.

Bundle the drain hose, refrigerant pipes, and

signal cable according to Fig. 3.10.

Indoor Unit

Space behind unit

Refrigerant piping

Drain hose

Signal wire

Insulation tape

DRAIN HOSE MUST BE ON BOTTOM

Make sure that the drain hose is at the bottom

of the bundle. Putting the drain hose at the

top of the bundle can cause the drain pan

to overﬂow, which can lead to ﬁre or water

damage.

DO NOT INTERTWINE SIGNAL CABLE WITH

OTHER WIRES

While bundling these items together, do not

intertwine or cross the signal cable with any

other wiring.

2.

Using adhesive vinyl tape, attach the drain

hose to the underside of the refrigerant pipes.

3.

Using insulation tape, wrap the signal wire,

refrigerant pipes, and drain hose tightly

together. Double-check that all items are

bundled in accordance with Fig. 3.10.

DO NOT WRAP ENDS OF PIPING

When wrapping the bundle, keep the ends

of the piping unwrapped. You need to access

them to test for leaks at the end of the

installation process (refer to Electrical Checks

and Leak Checks section of this manual).

Step 8: Mount indoor unit

If you installed new connective piping to the

outdoor unit, do the following:

1.

If you have already passed the refrigerant

piping through the hole in the wall, proceed

to Step 4.

2.

Otherwise, double-check that the ends of the

refrigerant pipes are sealed to prevent dirt or

foreign materials from entering the pipes.

3.

Slowly pass the wrapped bundle of refrigerant

pipes, drain hose, and signal wire through the

hole in the wall.

4.

Hook the top of the indoor unit on the upper

hook of the mounting plate.

5.

Check that unit is hooked firmly on mounting

by applying slight pressure to the left and

right-hand sides of the unit. The unit should

not jiggle or shift.

6.

Using even pressure, push down on the

bottom half of the unit. Keep pushing down

until the unit snaps onto the hooks along the

bottom of the mounting plate.

7.

Again, check that the unit is ﬁrmly mounted

by applying slight pressure to the left and the

right-hand sides of the unit.

Fig. 3.10

Indoor Unit

Installation

THE WIRING CONNECTION PROCESS MAY

DIFFER SLIGHTLY BETWEEN UNITS.

 Page 19 

If refrigerant piping is already embedded in

the wall, do the following:

1.

Hook the top of the indoor unit on the upper

hook of the mounting plate.

2.

Use a bracket or wedge to prop up the unit,

giving you enough room to connect the

refrigerant piping, signal cable, and drain

hose. Refer to Fig. 3.11 for an example.

Fig. 3.11

Fig. 3.12

Move to left or right

30-50mm

(1.2-1.95in)

30-50mm

(1.2-1.95in)

Indoor Unit

Installation

3.

Connect drain hose and refrigerant piping

(refer to Refrigerant Piping Connection

section of this manual for instructions).

4.

Keep pipe connection point exposed to

perform the leak test (refer to Electrical

Checks and Leak Checks section of this

manual).

5.

After the leak test, wrap the connection point

with insulation tape.

6.

Remove the bracket or wedge that is propping

up the unit.

7.

Using even pressure, push down on the

bottom half of the unit. Keep pushing down

until the unit snaps onto the hooks along the

bottom of the mounting plate.

UNIT IS ADJUSTABLE

Keep in mind that the hooks on the mounting plate are smaller than the holes on the back of the

unit. If you ﬁnd that you don’t have ample room to connect embedded pipes to the indoor unit, the

unit can be adjusted left or right by about 30-50mm (1.25-1.95in), depending on the model. (See

Fig. 3.12

.)

 Page 20 

Outdoor Unit Installation

5

Outdoor Unit

Installation

evoba )ni42( mc06

60cm (24in)

on right

30cm (12in)

on left

200cm (79in)

in front

30cm (12in)

from back wall

Installation Instructions – Outdoor

Unit

Step 1: Select installation location

Before installing the outdoor unit, you must

choose an appropriate location. The following

are standards that will help you choose an

appropriate location for the unit.

Proper installation locations meet the

following standards:



Meets all spatial requirements shown in

Installation Space Requirements (Fig. 4.1)



Good air circulation and ventilation



Firm and solid—the location can support the

unit and will not vibrate



Noise from the unit will not disturb others



Protected from prolonged periods of direct

sunlight or rain

DO NOT

install unit in the following locations:

Near an obstacle that will block air inlets

and outlets

Near a public street, crowded areas, or

where noise from the unit will disturb others

Near animals or plants that will be harmed

by hot air discharge

Near any source of combustible gas

In a location that is exposed to large

amounts of dust

In a location exposed to a excessive amounts

of salty air

Fig. 4.1

Page is loading ...

NAPOLEON NC19-24F-I-B User manual

This manual is also suitable for

NAPOLEON NC19-24F-I-B User manual

in other languages

Related papers

Other documents