- 1 -
Quick Installation Guide
Version 1.0
Power-over-Ethernet Interface Cards
PoE-i211 & i214
Form Factor Ethernet Controller PoE PSE Controller
PCI Express
®
x1 Intel
®
Ethernet Controller
i210IT
Linear Tech LTC4266C
♦ Technical Support
If you have any technical difculties, please consult the user’s manual rst at:
ftp://ftp.arbor.com.tw/pub/manual
Do not hesitate to contact our customer service at the following addresses if your problem
persists.
http://www.arbor.com.tw
E-mail: info@arbor.com.tw
♦ Declaration of Conformity
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions : (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Copyright® 2013 All Rights Reserved. 4040021100100P
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
- 2 -
Packing List
Before starting with the installation, make sure the following items are shipped:
or
PoE-i211
PoE-i214
One PoE-i211 or PoE-i214
Power-over-Ethernet interface
card
One Driver CD
One Quick Installation Guide
One Power Cable
(for PoE-i214 only)
Ordering Information
PoE-i211 Single-channel PoE card
PoE-i214 4-channel PoE card with power cable
Specications
Form Factor PCI Express
®
x1
Dimensions (W x D) 168 x 111 mm (6.61” x 4.37”)
Ethernet Controller
Intel
®
i210IT, One Intel
®
i210IT Ethernet Controller (PoE-i211)
Intel
®
i210IT, Four Intel
®
i210IT Ethernet Controllers (PoE-i214)
PCI Express
®
Switch PLX PEX8608 PCI Express
®
switch (for PoE-i214 only)
PoE PSE Controller Linear Tech LTC4266C
Cable Requirement CAT-5e or CAT-6 cable, maximum 100 meters
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
- 3 -
OS Support
Windows XP Embedded, Windows 7 Professional, Windows 8
Ubuntu 11.10 above
Linux distributions with kernel 3.0 above
Power
Power Requirement
For PoE-i211 (1 x Ethernet port):
• Maximum 1.6A @ 3.3 VDC from PCI Express bus
• Maximum 2.8A @ 12 VDC directly from PCI Express bus
For PoE-i214 (4 x Ethernet ports):
• Maximal 2.4A @ 3.3VDC from PCI Express bus
• Maximal 5.6A @12VDC, directly from 4 pin AT/ATX power connector
Power consumption
Typical: 5W
Maximum: 65W w/ 4 x PoE power load
PoE Power Output
802.3af compliant (802.3AT type 1)
Powered Device (PD) auto detection
Power Level Classication: Class 0, 1, 2 ,3
15.4W@48VDC power output (per port)
Environmental
Operating Temp. -40ºC ~ 85ºC (-40ºF ~ 185ºF)
Storage Temp. -40ºC ~ 85ºC (-40ºF ~ 185ºF)
Operating Humidity 0%~95% @ 85°C (non-condensing)
Regulatory & Safety
Hipot 1.5KV
Surge ± 2KV surge protection
Conformity CE, FCC Class A, RoHS
Find Drivers on CD
O.S. Driver Path
Windows 32 bit (XP, 7, 8) \PROWin32\APPS\PROSETDX\Win32\DxSetup.exe
Windows 64 bit (XP, 7, 8) \PROWinx64\APPS\PROSETDX\Winx64\DxSetup.exe
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
- 4 -
Board Dimensions - PoE-i211
Unit: mm
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
- 5 -
Board Dimensions - PoE-i214
Unit: mm
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
- 6 -
Location Diagram - PoE-i211
3 2
14
1
PSYIN1
LLED1
Location Diagram - PoE-i214
3 2
14
1
1
1
1
PSYIN1
LLED1
LLED2
LLED3
LLED4
Jumpers & Connectors
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
- 7 -
Pin Assignment
PSYIN1
Function: External power-in
Connector type: Right angle DIP power
connect with post.
Power Input: 9VDC to 36VDC
Pin Desc. Pin Desc.
1 GND 3 VinB
2 GND 4 VinA
► Pin 1 and Pin 2 are negative voltage.
► Pin 3 and Pin 4 are positive voltage,
12VDC to 36VDC.
LLED1,2,3,4
1
Function: Extends LAN LED
Connector type: 1x4-pin header
• LLED1
Pin Desc.
1 LAN1_LED_1000-
2 LAN1_LED_100-
3 LAN1_LEDPWR
4 LAN1_LED_ACT_
• LLED2
Pin Desc.
1 LAN2_LED_1000-
2 LAN2_LED_100-
3 LAN2_LEDPWR
4 LAN2_LED_ACT_
• LLED3
Pin Desc.
1 LAN3_LED_1000-
2 LAN3_LED_100-
3 LAN3_LEDPWR
4 LAN3_LED_ACT_
• LLED4
Pin Desc.
1 LAN4_LED_1000-
2 LAN4_LED_100-
3 LAN4_LEDPWR
4 LAN4_LED_ACT_
► Pin 1 is Giga LED. Pin 2 is Mega LED. Pin
1 and Pin 2 are using double-anode type
LED.
► Pin 3 is active LED Hi. Pin 4 is active LED
Low
3 2
14
Pin Assignment
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
- 8 -
This page is intentionally left blank.
Russia: LLC “ID Solution”, +7 495 545 3283,
www.idsolution.ru
/
