AMP Lighting AAL-1013-B-BZ-R1 Installation guide

Type
Installation guide

This manual is also suitable for

AMP Lighting AAL-1013-B-BZ-R1 is a low voltage landscape lighting fixture designed for outdoor use. It features a MR16 lamp with a maximum wattage of 20 watts, providing ample illumination for pathways, gardens, and other outdoor areas. The fixture is made of durable materials and is built to withstand harsh weather conditions. It comes with a stake for easy installation in the ground and can be adjusted to provide the desired lighting angle. The AMP Lighting AAL-1013-B-BZ-R1 is a versatile and efficient lighting solution for enhancing the ambiance and safety of your outdoor space.

AMP Lighting AAL-1013-B-BZ-R1 is a low voltage landscape lighting fixture designed for outdoor use. It features a MR16 lamp with a maximum wattage of 20 watts, providing ample illumination for pathways, gardens, and other outdoor areas. The fixture is made of durable materials and is built to withstand harsh weather conditions. It comes with a stake for easy installation in the ground and can be adjusted to provide the desired lighting angle. The AMP Lighting AAL-1013-B-BZ-R1 is a versatile and efficient lighting solution for enhancing the ambiance and safety of your outdoor space.

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP
®
Low Voltage Landscape Lighting
AMP
®
AggregatePro Spotlight
AAL-1013-XX-B-BZ
AMP
®
AggregatePro Spotlight
AAL-1013-XX-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
[email protected] • 813.978.3900
Product Dimensions
–3–
1
Package Contents
Remove Glare Guard
A. (1) Fixture
B. (1) Stake
7”
3”
2”
Loosen the set screw and
remove the glare guard from
the xture.
Glare
Guard
Set Screw
Fixture
INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP
®
AggregatePro Spotlight
AAL-1013-XX-B-BZ
Remove Lens
Install Lamp
Loosen the lens and remove it from
the xture.
Fixture
Lens
Socket
Fixture
Insert the lamp with the correct
wattage and type marked on the
xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare
hands. Use soft cloth to handle lamp.
MR16 Lamp
[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP
®
AggregatePro Spotlight
AAL-1013-XX-B-BZ
Install Lens
Install Glare Guard
Place the lens over the lamp and
thread onto the xture.
Lens
Fixture
Attach the glare guard back onto
the lens and secure with the set
screw. Tighten until snug.
Fixture
Glare
Guard
Set Screw
INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
AMP
®
AggregatePro Spotlight
AAL-1013-XX-B-BZ
Install Stake
Board
Stake
Soil
Ground
Determine the desired location for
mounting the xture. Hammer the
stake into the ground until ange
of stake is ush to grade. To avoid
damage to the stake, place a board
on top of the stake while hammering.
NOTE: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
7
Install Fixture to Stake
Fixture
Stake
Pigtail
Clear away an area in the
ground at the wireway slot
on top of the stake. Lay the
luminaire pigtail into the
wireway slot and screw the
xture on to the stake. Tighten
until snug.
Wireway Slot
–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Lamp
Strip both the leads from the luminaire pigtail. Using two wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors
8
Install Fixture to Stake
Loosen the set screw on glare guard, remove the glare guard and the lens
to expose the lamp. Replace it with the correct wattage and type marked
on the xture label. Then reinstall the lens and glare guard and tighten
with the set screw.
IMPORTANT: Lamp must be protected from moisture and dust at all times.
Always reinstall the lens and glare guard when moved.
IS-AAL-1013-XX-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP
®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AMP Lighting AAL-1013-B-BZ-R1 Installation guide

Type
Installation guide
This manual is also suitable for

AMP Lighting AAL-1013-B-BZ-R1 is a low voltage landscape lighting fixture designed for outdoor use. It features a MR16 lamp with a maximum wattage of 20 watts, providing ample illumination for pathways, gardens, and other outdoor areas. The fixture is made of durable materials and is built to withstand harsh weather conditions. It comes with a stake for easy installation in the ground and can be adjusted to provide the desired lighting angle. The AMP Lighting AAL-1013-B-BZ-R1 is a versatile and efficient lighting solution for enhancing the ambiance and safety of your outdoor space.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI