Altec SI-MAX Installation guide

Brand: Altec

Model: SI-MAX

Type: Installation guide

- 1 -

NOTINS0UK000009-V2.02

INSTALLATION MANUAL

Indoor siren self-powered

Version 2

Made in France

SI-MAX

Non contractual photo

SI-MAX is admitted to NF and A2P « 3 shields » in accordance with the standard NFC48-265 and with

the certification standard NF324-H58

with the number : 3130000280 -- Manufacturing unit : N° 122 P2

CNPP Certification (centre national de prévention et de protection):

http://www.cnpp.com

AFNOR Certification :

http://www.marque-nf.com

According to the continuous improvement of our products, the information contained in this guide may

be subject to change without notice. ATLS may not be held liable for any errors contained in this

document, nor incidental or consequential damages relating to the supply, the quality or use of this

document.

The products of the range ALTEC are designed and made in France by the company ATLS

SI-MAX and ALTEC are registered trademark of ATLS

- 2 -

DESCRIPTION

With its metal housing, the SI-MAX is the essential solution to deter all the intruders thanks to its very

high power sound!

In alarm, the SI-MAX draws its energy only in the backup battery to prevent damage of the charger of

the control panel.

An automatic limitation of the load current at 100 mA, even permits several sirens supplied by the

same control panel without risk.

The ISBC function (Intelligent System of Battery Charging) adjusts automatically the charging

voltage of the battery at 13,8V, the SI-MAX guarantees its full power even when the external power

supply delivers 12V only.

INSTALLATION

The SI-MAX is exclusively provided for an indoor use. It is fixed on

a vertical wall and flat surface greater than the surface of its box,

leaving at least 2 cm on each side. Fix the back plate of the SI-

MAX using 4 screws with cylinder head diameter of 4 to 5 mm (not

supplied).

The removal tamper is ensured by a screw of 60-70mm of length

and 4 to 5 mm of diameter (not supplied) that should be positioned

as shown against. It must be screwed into the wall until its head

comes into contact with the electronic circuit without forcing.

The opening tamper is ensured automatically by the slide switch

actuated by the screw cover.

It is imperative to test and verify the proper functioning of the

audible and the tampers after the installation.

It is strongly recommended to check periodically the proper tightening of connections and the status of

the backup battery and replace it if necessary.

WIRING

Backup battery

Power supply with current limiting battery

OV power supply

Blocking input 1 intrusion modulation

Blocking input 2 discontinuous modulation

Tamper circuit

Position of the screw for removal tamper

Switch for opening tamper

Switches of configuration

• Before wiring the tamper, check that the circuit does not exceed 60VDC/0,1A.

• Check the correct operation of the tamper after the installation by lifting the cover.

• If the equipment that drives the SI-MAX is not the same that the one which provides the

power, you have to connect the terminal « 0V » to this equipment to obtain a common

reference.

WARNING ! The SI-MAX will start to trigger only with the internal battery.

- 3 -

OPERATION

The SI-MAX has two blocking inputs that can be setup: the first (INPUT 1) triggers the modulation

of the intrusion alarm, the second (INPUT2) triggers the discontinuous modulation. The operating

mode of each input can be setup with 5 switches.

Function INPUT 1 (Intrusion modulation) INPUT 2 (Discontinuous modulation)

Position Switch 1 Switch 2 Switch 3 Switch 4 Switch 5

NEGATIVE

(1)

APPEAR

(1)

NEGATIVE

(1)

APPEAR

(1)

ACTIVATED

OFF POSITIVE DISAPPEAR POSITIVE DISAPPEAR

DEACTIVATED

(1) : operating mode non-authorized for installations certificated NF & A2P

By default, the « INPUT1 » is the only one that can trigger by disappear of a positive blocking signal,

« INPUT 2 » being disabled, the configuration switch N°5 must be set to ON in order to allow this

operation.

At power up, regardless the state of blocking inputs, the SI-MAX does not trigger. The inputs must first

be armed (return to a normal blocking state) during at least one second to permit every triggering.

If an input is set by appear, the SI-MAX triggers when the control voltage appears.

At the triggering of any blocking input, the alarm is activated for a period of 31 minutes or until the

return to a normal state of the corresponding input.

« INPUT 1 » has the priority and can interrupt the alarm triggered by the « INPUT 2 » and start the

intrusion modulation.

SAFETY INSTRUCTIONS

• During the tests, wear a hearing protective helmet or hold you at a reasonable distance

of the SI-MAX.

• Do not perform any operation on SI-MAX in stormy weather.

• Use only the type of the batteries indicated on the specifications table

Destruction of the batteries

The backup battery for the SI-MAX is not supplied by ATLS. However, do not dispose of batteries in

your trash, it is forbidden to cremate, bury them or throw them into landfills. Dispose batteries

according to the current laws and regulations. Please contact relevant authorities for further

information on the arrangements taking place in your country to collect, to recycle and to dispose of

used batteries.

Destruction of the product

As required by the WEEE (Waste Electrical and Electronic Equipment), electrical and electronic

equipment must be disposed separately from normal household garbage to promote their re-

use, recycling and other forms of recovery, as well as limit the amount of waste requiring

disposal and thereby reduce the landfill. When disposing of such products, please follow the

instructions of local authorities and / or check with your provider when purchasing a new

product.

- 4 -

WARRANTY

ATLS provides a guarantee of 5 years from the date of the manufacture.

The year and month of manufacture appear on the label serial number placed

inside the device.

The warranty does not cover non-functional damage such as scratches, broken by

a fall or shock or degradation caused by abnormal use.

The guarantee applies only to cards and electronic assemblies and does not cover damage caused by

natural or artificial surges.

The guarantee applies only if the electronic part has not been dismantled, disturbed or transformed.

The warranty is strictly limited to repair or exchange parts that we found defective.

Return costs are still born by the sender.

The detention of equipment under warranty won’t give rise to any compensation for any reason

whatsoever.

The responsibility of A.T.L.S. is limited to the repair of products and do not extend to the

consequences of their use, their implementation or their non-functioning.

TECHNICAL FEATURES

Voltage on +12V CHARGE :

from 12,0 to 14,5 VDC

Output voltage on +BAT :

13.8 VDC (+/-0.2 Vdc)

Residual ripple allowed :

250mV

Consumption in standby :

5 mA

Autonomy in internal battery :

72 hours

Duration of the alarm :

31 minutes

Consumption in alarm & sound power :

(with INPUT1, after 3mn, the sound power given

decreases to increase the autonomy)

INPUT 1 : 1.7A 114 dBa at 1m. / 3mn.

1.0A 110 dBa at 1m. / 28mn.

INPUT 2 : 0.2A 103 dBa at 1m.

Control voltage max. « INPUT 1 / 2 » :

16 VDC (0,1mA)

Triggering voltage « INPUT 1 / 2 » :

Disappear : <1VDC (positive) / 6VDC (negative)

Appear : >6VDC (positive) / <1VDC (negative)

Reset voltage « INPUT 1 / 2 » :

Disappear : >6VDC (positive) / <1VDC

(negative)

Appear : <1VDC (positive) / >6VDC (negative)

Degree of protection :

IP 31 IK 08

Environment :

Class II – General indoor

Operating temperature :

-10°C to +55°C

Cable type for the connection:

Cable 3 pairs rigid : Ø >= 0,5mm

flexible : Ø >= 0,2mm

Type of backup batteries:

12V 2.1Ah YUASA NP2.1-12FR

12V 2.1Ah YUCELL Y2.1-12FR

12V 2.0Ah POWERSONIC PS 1220 V0

12V 2.2Ah ELECKSON BEL120022

12V 2.3Ah ACD ST20

12V 2.3Ah SUNLIGHT SP 12-2.1V0

Electromagnetic compatibility: in accordance with the norms NF EN 50130-4 and NF EN 55022

Electric security: in accordance with the norm EN 60950-1 + A11

Altec SI-MAX Installation guide

Altec SI-MAX Installation guide

Altec SI-MAX Installation guide

Related papers

Other documents