Santec KLASSICA 9570KL Operating instructions

Brand: Santec

Model: KLASSICA 9570KL

Category: Sanitary ware

Type: Operating instructions

This manual is also suitable for

KLASSICA COLLECTION

MODEL: 9570KL

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

Important : Please register your product online at www.santecfaucet.com within

30 days of purchase. Santec reserves the right to request additional documents

before servicing warranty requests.

0 1

MODEL: 9570KR

MODEL: 9570KT

BIDET

Vacuum Br eaker

NOTE: See diagram on next page for removing and reinstalling the

complete trim.

Remove the complete trim from the Vacuum Breaker valve.

Insert Vacuum Breaker valve up from below and reinstall complete trim

except for the handle cap. Make sure to install the black plastic lock

nut in the position shown in the diagram on the next page. Snugly

tighten down the black plastic lock nut and trim cylinder by hand

tightening only.

until it stops. Pop the handle cap into the handle with the “spritzer”

icon facing frontwards or at the 6 o’clock position (see handle cap

diagram below).

supply lines.

Hole size for the spout and Handle Trim is a minimum of 1-1/4” and a

maximum of 1-1/2”.

Vacuum Breaker Installation

1 2

Spritzer

Handle Cap

9570 KL, KR, KT _ _

Black plastic lock nut

Trim Cylinder

Handle

Screw

Handle Cap

Black Soft Seating China Seals

White Nylon Slip Washer

Vacuum Breaker Valve

Elbow

Wye

Complete Trim

9570KL, KR, KT _ _

Han dle Tr i m

Remove the Valve Body Mounting Hardware from the valve body. Slip

appropriate hole next to the vacuum breaker (HOT-left & COLD-right).

Apply a ring of silicone caulking around the handle hole on the bidet

top. DO NOT USE PLUMBER’S PUTTY, WHICH CAN DAMAGE FINISH.

Connecting Hoses toward Wye Connector.

For proper handle turning direction, install the handle with the “COLD”

blue label at the right side of the sink (front view) and the handle with

the “HOT” red label at the left side of the sink.

HANDLE TRIM IS READY FOR DROP-IN INSTALLATION. DO NOT

DISASSEMBLE HANDLE TRIM.

Handle Trim Installation (1)

Valve Body

Mounting Hardware

Washer

Brass Lock Nut

Wye c onnecting hoses

0 5

9570KL, KR, KT _ _

From beneath of the bidet, screw the Valve Body Mounting Hardware

back onto the valve body. First the washer, then the brass lock nut.

Align the lever or cross handle properly against the vacuum breaker

the Inlet Hoses to the Supply Lines. Tighten to avoid leakage.

Han dle Tr i m

Washer

Brass lock nut

Handle Trim Installation (2)

Inlet Hose

Supply Line

0 60 6

9570KL, KR, KT _ _

Sprit z e r

Apply a ring of silicone caulking around the hole designated for Spritzer

Slip Spritzer through the appropriate hole in bidet. From underneath

attach the Rubber Washer, Metal Washer and Shank Lock Nut. Tighten

Attach 24” hose from Spritzer to bidet elbow and tighten both ends

Spritzer Installation

Bidet

Basin

Rubber washer

Shank lock nut

Metal washer

Hou sin g

Basket

Wash e r

Spritzer Assembly

Spri tzer

Front View

9570KL, KR, KT _ _

Pop U p Drai n

Remove Drain Flange and Drain Plug from pop-up assembly.

Apply a ring of silicone caulking to underside of Drain Flange. Do not use

Insert the threaded end of the assembly up from below and into the pop up

drain hole.

Completely thread the drain body into the Drain Flange and align with the Ball

Rod Hole facing back. Then tighten lock nut from below. Clean excess silicone

with paper towel.

Pop Up Drain Installation (1)

Drain Plug

Drain Flange

Ball Rod Hole

Gasket

Washer

Lock nut

9570KL, KR, KT _ _

Remove the Brass Lock Nut, Rubber Washer and Metal Washer from the

lift rod assembly. Insert Lift Rod Flange into designated hole and

reassemble the Metal Washer, Rubber Washer and Brass Lock Nut from

below the bidet basin. Firmly tighten the Brass Lock Nut to secure Lift

Rod Flange.

Insert the Lift Rod into Lift Rod Flange from above.

P op Up D rai n

Pop Up Drain Installation (2)

Metal Washer

Rubber Washer

Brass Lock Nut

Lift Rod

Lift Rod Flange

9570KL, KR, KT _ _

Insert Drain Plug into Drain Flange. Make sure the adjustable eye-screw

it.

Insert Ball Rod Washer into drain body followed by the Ball Rod, 2nd

Washer and Ball Rod Nut. Tighten the Ball Rod Nut until snug.

Gently push the Horizontal Ball Rod down to place the plunger in the

up position.

Connect the Lift Rod with the Ball Rod using the Pop-up connection and

tighten securely with screwdriver.

Test Pop-up for smooth operation and adjust if necessar y.

Drain plug

Drain tube

Lift rod

Pop-up connection

Pop Up Dr a i n

Pop Up Drain Installation (2)

Ball rod

assembly

(ball rod, ball rod

nut, & 2 washers)

9570KL, KR, KT _ _

Flu s h T h e Lin e

After all connections have been made from inlet supplies to angle

stops, remove Spritzer Housing, Basket and Washer (see Spritzer

Installation on page 5).

Open both hot and cold valves. Slowly open angle stops from below

Turn water off and reinstall Spritzer Housing, Basket and Washer.

INLET HOSEINLET HOSE

WARNING

: Do not clean your SANTEC product with ammonia (Window cleaner), bleach, soaps, acids,

abrasives, harsh polishes, harsh cleaners, a coarse surfaced cloth, coarse sponge, or any type of scouring

Polished & Satin 24K Gold :

The Karat mark states the percentage of pure gold -- 24K is 100 percent gold. As one of

the Earth's most precious metals, gold is the most supple and malleable of all metals. Gold-plated faucets scratch easily. To

clean, wipe down with a dry soft cloth after each use. Gold surfaces should be coated with a thin layer of non-abrasive carnauba

wax or liquid car wax up to 3 or 4 times per year. This will prevent water spotting and water deposit buildup. We recommend

using SANTEC’s Polish which has been formulated to clean and seal, leaving behind a protective coating th

at will resist

tarnishing and improve water repellency.

Antique Bronze :

Antique bronze simulates the antiquity of Old-World craftsmanship with a golden base color and a blend

of dark undertones. To clean, wipe down with a dry soft cloth after each use. Antique Bronze should be coated with a thin layer

of non-abrasive carnauba wax or liquid car wax up to 3 or 4 times per year. We recommend using SANTEC’s Polish which has

been formulated to clean and seal, leaving behind a protective coating that will resist tarnishing and improve water repellency.

Oil Rubbed Bronze :

Oil-rubbed bronze simulates the antiquity of Old-World craftsmanship with its warm, dark brown

color and copper undertones. To clean, wipe down with a dry soft cloth after each use. Oil-rubbed bronze should be coated with

a thin layer of non-abrasive carnauba wax or liquid car wax up to 3 or 4 times per year. We recommend using SANTEC Polish

which has been formulated to clean and seal, leaving behind a protective coating that will resist tarnishing and improve water

repellency.

Polished Chrome:

use. A non-abrasive all-metal cleaner can then be applied to restore the shine. The surface can also be coated with a thin layer of non-abrasive

carnauba wax or liquid car wax. This will prevent water spotting and water deposit buildup. We recommend using SANTEC’s Polishwhich

has been formulated to clean and seal, leaving behind a protective coating that will resist tarnishing and improve water repellency.

Polished and Satin Nickel

Thank you for making SANTEC a part of your lifestyle and luxury spa experience. Our products have been created as works of

CLE AR CO ATED F I N ISHES

N O N-CLE AR COATED FINISHE S

F INISH C ARE INFORMATIO N

PLEASE REGISTER YOUR PRODUCT ONLINE FOR WARRANTY SERVICES

www.santecfaucet.com/registration

SANTEC

A non-abrasive all-metal cleaner can then be applied to restore the shine. The surface can also be coated with a thin layer of non-abrasive

carnauba wax or liquid car wax. This will prevent water spotting and water deposit buildup. We recommend using SANTEC’s Polishwhich

has been formulated to clean and seal, leaving behind a protective coating that will resist tarnishing and improve water repellency.

use.

This warranty does not cover:

SANTEC res

erves the right to examine any product claimed defective prior to any warranty claim being accepted or processed,

state.

Damage due to negligence, accident, abuse, improper installation, or improper maintenance such as, but not limited to: heat

from soldering during installation, the use of plumber’s putty, damage from tools used during installation, the use or exposure

to chemicals or cleaning products either abrasive or non-abrasive, or the use of any cleaning tool or product other than a

altered or used in a manner not typical for the product.

Loss, damages, or expense, incidental or consequential whatsoever, originating from the purchase, installation, use, repair,

failure, or replacement of any

SANTEC pro

duct or part, allowed by law.

Commercial and/or Industrial installations and use of the product.

This warranty does not include labor, travel charges, or any costs incurred for repair, removal, installation, servicing,

diagnosing, or handling of either defective or replacement parts.

SANTEC is committed to enhancing your bathroom experience by creating luxury products that will provide enduring

satisfaction. Every

effort has been made to satisfy the highest standards of design and production, to create lasting peace of

mind for our customers. We provide the following limited warranties on our products:

Limited Warranty against all manufacturer’s defects and tarnish.

Finishes:

Mechanical:

A Lifetime Limited Warranty is provided on parts to be free from failure related to defects in materials and

workmanship.

SANTEC

cartridges carry a Five (5) Year Limited Warranty against manufacturer’s defects.

This warranty extends to the original consumer purchaser only and extends for as long as the original purchaser owns the

product and the home in which the product is installed.

Please read ‘WHAT IS COVERED BY OUR WARRANTY’ and ‘EXCLUSIONS AND LIMITATIONS OF WARRANTY’ sections to

understand what is and what is not covered. Please have ready the proof of purchase (original sales receipt), description of the

problem, and carefully package the product or defective part with postage prepaid.

Then, please contact your local

SANTEC

Showroom or write to

SANTEC

Technical Services.

L IFET I ME LIMITE D WARRANTY

L ENGTH OF WA RRAN TY & WHO IS COVE RED BY O U R WARRANTY

WHAT IS COVERED BY OUR WA RRANTY

E X C LUSIO NS AND LI MITATIONS OF WARRANTY

T O OB TAIN WARRAN TY SER VICE

SANTEC

Access should be provided to the roman tub valves for future service or repair to valves and piping. Under no

circumstances will Santec Faucet, Inc. be liable for anycosts associated with the removal of materials for future

access to the tub valves or piping for service or repair.

Santec KLASSICA 9570KL Operating instructions

Brand: Santec

Model: KLASSICA 9570KL

Category: Sanitary ware

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Santec KLASSICA 9570KL Operating instructions

This manual is also suitable for

Santec KLASSICA 9570KL Operating instructions

Related papers

Other documents