Neff B4AVH1AH0B Installation guide
- Category
- Kitchen & houseware accessories
- Type
- Installation guide
en Safety
2
Table of contents
USER MANUAL
1 Safety....................................................................2
2 Preventing material damage ...............................4
3 Environmental protection and saving en-
ergy .......................................................................5
4 Familiarising yourself with your appliance ........6
5 Accessories..........................................................9
6 Before using for the first time ...........................10
7 Basic operation ..................................................11
8 Steam..................................................................11
9 Time-setting options..........................................13
10 Programme.........................................................15
11 Childproof lock...................................................16
12 Rapid heating .....................................................16
13 Basic settings.....................................................17
14 HomeConnect ...................................................18
15 Cleaning and servicing......................................20
16 Cleaning function...............................................23
17 Shelf supports....................................................24
18 Appliance door...................................................24
19 Troubleshooting.................................................28
20 Disposal..............................................................30
21 Customer Service...............................................31
22 How it works.......................................................31
23 INSTALLATION INSTRUCTIONS .......................35
23.1 General installation instructions....................
...36
1 Safety
Observe the following safety instructions.
1.1 General information
¡ Read this instruction manual carefully.
¡ Keep the instruction manual and the
product information safe for future refer-
ence or for the next owner.
¡ Do not connect the appliance if it has been
damaged in transit.
1.2 Intended use
This appliance is designed only to be built
into kitchen units. Read the special installation
instructions.
Only a licensed professional may connect ap-
pliances without plugs. Damage caused by in-
correct connection is not covered under the
warranty.
Only use this appliance:
¡ To prepare meals and drinks.
¡ In private households and in enclosed
spaces in a domestic environment.
¡ Up to an altitude of max. 4000m above
sea level.
1.3 Restriction on user group
This appliance may be used by children aged
8 or over and by people who have reduced
physical, sensory or mental abilities or inad-
equate experience and/or knowledge,
provided that they are supervised or have
been instructed on how to use the appliance
safely and have understood the resulting
dangers.
Children must not play with the appliance.
Children must not perform cleaning or user
maintenance unless they are at least 15 years
old and are being supervised.
Keep children under the age of 8 years away
from the appliance and power cable.
1.4 Safe use
Always place accessories in the cooking com-
partment the right way round.
→"Accessories", Page9
WARNING‒Risk of fire!
Combustible objects that are left in the cook-
ing compartment may catch fire.
▶
Never store combustible objects in the
cooking compartment.
▶
If smoke is emitted, the appliance must be
switched off or the plug must be pulled out
and the door must be held closed in order
to stifle any flames.
Loose food remnants, fat and meat juices
may catch fire.
▶
Before using the appliance, remove the
worst of the food residues and remnants
from the cooking compartment, heating ele-
ments and accessories.
Safety en
3
Opening the appliance door creates a
draught. Greaseproof paper may come into
contact with the heating element and catch
fire.
▶
Never place greaseproof paper loosely
over accessories when preheating the ap-
pliance and while cooking.
▶
Always cut greaseproof paper to size and
use a plate or baking tin to hold it down.
WARNING‒Risk of burns!
The appliance and its parts that can be
touched become hot during use.
▶
Caution should be exercised here in order
to avoid touching heating elements.
▶
Young children under 8 years of age must
be kept away from the appliance.
Accessories and cookware get very hot.
▶
Always use oven gloves to remove ac-
cessories or cookware from the cooking
compartment.
When the cooking compartment is hot, any al-
coholic vapours inside may catch fire.
▶
Only use small quantities of drinks with a
high alcohol content in food.
▶
Open the appliance door carefully.
WARNING‒Risk of scalding!
The accessible parts of the appliance become
hot during operation.
▶
Never touch these hot parts.
▶
Keep children at a safe distance.
Hot steam may escape when you open the
appliance door. Steam may not be visible, de-
pending on the temperature.
▶
Open the appliance door carefully.
▶
Keep children at a safe distance.
If there is water in the cooking compartment
when it is hot, this may create hot steam.
▶
Never pour water into the cooking compart-
ment when the cooking compartment is
hot.
WARNING‒Risk of injury!
Scratched glass in the appliance door may
develop into a crack.
▶
Do not use any harsh or abrasive cleaners
or sharp metal scrapers to clean the glass
on the oven door, as they may scratch the
surface.
The hinges on the appliance door move when
the door is opened and closed, which could
trap your fingers.
▶
Keep your hands away from the hinges.
Components inside the appliance door may
have sharp edges.
▶
Wear protective gloves.
WARNING‒Risk of electric shock!
Incorrect repairs are dangerous.
▶
Repairs to the appliance should only be
carried out by trained specialist staff.
▶
Only use genuine spare parts when repair-
ing the appliance.
▶
If the power cord of this appliance is dam-
aged, it must be replaced by trained spe-
cialist staff.
If the insulation of the power cord is dam-
aged, this is dangerous.
▶
Never let the power cord come into contact
with hot appliance parts or heat sources.
▶
Never let the power cord come into contact
with sharp points or edges.
▶
Never kink, crush or modify the power
cord.
An ingress of moisture can cause an electric
shock.
▶
Do not use steam- or high-pressure clean-
ers to clean the appliance.
If the appliance or the power cord is dam-
aged, this is dangerous.
▶
Never operate a damaged appliance.
▶
Never operate an appliance with a cracked
or fractured surface.
▶
Never pull on the power cord to unplug the
appliance. Always unplug the appliance at
the mains.
▶
If the appliance or the power cord is dam-
aged, immediately unplug the power cord
or switch off the fuse in the fuse box.
▶
Call customer services. →Page31
WARNING‒Danger: Magnetism!
Permanent magnets are used in the control
panel or in the controls. These may affect
electronic implants, e.g. heart pacemakers or
insulin pumps.
▶
Wearers of electronic implants must stay at
least 10 cm away from the control panel.
WARNING‒Risk of suffocation!
Children may put packaging material over
their heads or wrap themselves up in it and
suffocate.
▶
Keep packaging material away from chil-
dren.
en Preventing material damage
4
▶
Do not let children play with packaging ma-
terial.
Children may breathe in or swallow small
parts, causing them to suffocate.
▶
Keep small parts away from children.
▶
Do not let children play with small parts.
1.5 Halogen bulb
WARNING‒Risk of burns!
The bulbs in the cooking compartment get
very hot. There is still a risk of burning for
some time after they have been switched off.
▶
Do not touch the glass cover.
▶
Avoid contact with your skin when cleaning.
WARNING‒Risk of electric shock!
When changing the bulb, the bulb socket con-
tacts are live.
▶
Before replacing the bulb, ensure that the
appliance is switched off in order to pre-
vent a potential electric shock.
▶
Also unplug the appliance from the mains
or switch off the circuit breaker in the fuse
box.
1.6 Steam
Follow these instructions when using a steam
function.
WARNING‒Risk of scalding!
The water in the water tank may become very
hot if you operate the appliance for long peri-
ods.
▶
Always empty the water tank after using the
steam function.
Hot steam is generated in the cooking com-
partment.
▶
Do not reach into the cooking compartment
when using steam.
Hot liquid may spill over the sides of the ac-
cessory when it is removed from the cooking
compartment.
▶
Remove hot accessories with care and al-
ways wear oven gloves.
WARNING‒Risk of fire!
Due to the hot surfaces, vapours from flam-
mable liquids may catch fire in the cooking
compartment (explosion). The appliance door
may spring open. Hot steam and jets of flame
may escape.
▶
Do not pour flammable liquids (e.g. alco-
holic drinks) into the water tank.
▶
Only fill the water tank with water or with
the descaling solution we have recommen-
ded.
2 Preventing material damage
2.1 General
ATTENTION!
Objects on the cooking compartment floor at over
50°C will cause heat to build up. The baking and
roasting times will no longer be correct and the enamel
will be damaged.
▶
Do not place any accessories, greaseproof paper or
foil of any kind on the cooking compartment floor.
▶
Only place cookware on the cooking compartment
floor if a temperature above 50°C has been set.
When the cooking compartment is hot, any water in-
side it will create steam. The change in temperature
may cause damage.
▶
Never pour water into the cooking compartment
when it is still hot.
▶
Never place cookware containing water on the
cooking compartment floor.
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶
Allow the cooking compartment to dry after use.
▶
Do not keep moist food in the cooking compartment
for a long time with the door closed.
▶
Do not store food in the cooking compartment.
Leaving the appliance to cool down with the door open
will damage the front of neighbouring kitchen units over
time.
▶
Always allow the cooking compartment to cool
down with the door closed after cooking at high
temperatures.
▶
Take care not to trap anything in the appliance
door.
▶
Only leave the cooking compartment to dry with the
door open if a lot of moisture was produced during
operation.
Fruit juice dripping from the baking tray leaves stains
that cannot be removed.
▶
When baking very juicy fruit flans, do not pack too
much on the baking tray.
▶
If possible, use the deeper universal pan.
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶
Never use oven cleaner in the cooking compartment
when it is still warm.
Environmental protection and saving energy en
5
▶
Remove all food remnants from the cooking com-
partment and the appliance door before you next
heat up the appliance.
If the seal is very dirty, the appliance door will no
longer close properly during operation. This may dam-
age the front of adjacent kitchen units.
▶
Keep the seal clean at all times.
▶
Never operate the appliance if the seal is damaged
or missing.
Sitting or placing objects on the appliance door may
damage it.
▶
Do not place or hang objects on the appliance door.
▶
Do not place cookware or accessories on the appli-
ance door.
With certain models, accessories may scratch the door
pane when closing the appliance door.
▶
Always push accessories fully into the cooking com-
partment.
2.2 Steam
Follow these instructions when using the steam func-
tion.
ATTENTION!
Silicone bakeware is not suitable for combined opera-
tion with steam.
▶
Cookware must be heat- and steam-resistant.
Using cookware with rust spots may cause corrosion in
the cooking compartment. Even the smallest spots of
rust can cause corrosion.
▶
Do not use cookware with rust spots.
Hot water in the water tank may damage the steam
system.
▶
Only fill the water tank with cold water.
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120°C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶
Remove descaling solution immediately with water.
Cleaning the water tank in the dishwasher will damage
it.
▶
Do not clean the water tank in the dishwasher.
▶
Clean the water tank with a soft cloth and standard
washing-up liquid.
3 Environmental protection and saving energy
Help protect the environment by using your appliance
in a way that conserves resources and by disposing of
reusable materials properly.
3.1 Disposing of packaging
The packaging materials are environmentally compat-
ible and can be recycled.
▶
Sort the individual components by type and dispose
of them separately.
Information about current disposal methods are
available from your specialist dealer or local author-
ity.
3.2 Saving energy
If you follow these instructions, your appliance will use
less power.
Only preheat the appliance if the recipe or the recom-
mended settings tell you to do so.
¡
Not preheating the appliance can reduce the en-
ergy used by up to 20%.
Use dark-coloured, black-coated or enamelled baking
tins.
¡
These types of baking tin absorb the heat particu-
larly well.
Open the appliance door as little as possible during
operation.
¡
This will maintain the temperature in the cooking
compartment and eliminate the need for the appli-
ance to reheat.
When baking multiple dishes, do so in succession or
in parallel.
¡
The cooking compartment is heated after baking
the first dish. This reduces the baking time for the
second cake.
If the cooking time is relatively long, you can switch
the appliance off 10minutes before the cooking time
ends.
¡
There will be enough residual heat to finish cooking
the dish.
Remove any accessories that are not being used from
the cooking compartment.
¡
Accessories that are not being used do not need to
be heated.
Allow frozen food to defrost before cooking.
¡
This will save the energy that would otherwise be
required to defrost it.
en Familiarising yourself with your appliance
6
4 Familiarising yourself with your appliance
4.1 Controls
You can use the control panel to configure all functions of your appliance and to obtain information about the operat-
ing status.
On certain models, specific details such as colour and shape may differ from those pictured.
2 43
1
5
1
Buttons
→"Buttons", Page6
2
Function selector
You can turn the function selector clockwise or
anti-clockwise from the zero setting.
→"Types of heating", Page7
→"Functions", Page8
3
Display
4
Temperature selector
Use the temperature selector to set the temper-
ature for the type of heating or select the set-
ting for other functions. You can turn the tem-
perature selector clockwise and anti-clockwise.
→"Temperature and setting levels", Page8
5
Water tank
Fill and empty the water tank.
→"Filling the water tank", Page12
→"After every steam operation", Page12
Note:Depending on the appliance type, the control
knobs can be pushed in. To click it in or out, push the
control knob in when it is in the off position.
4.2 Buttons
The buttons are touch-sensitive surfaces. Press the corresponding button to select a function.
Symbol Name Use
Time-setting options Sets the time, timer, cooking time or end time
→"Time-setting options", Page13
Left arrow Decreases the adjustment values
Right arrow Increases the adjustment values
Steam assistance Starts or cancels steam assistance
→"Steam", Page11
Rapid heating Starts or cancels rapid heating
→"Rapid heating", Page16
Familiarising yourself with your appliance en
7
Symbol Name Use
Information ¡ Displays the current cooking compartment temperature
¡ Set basic settings
→"Basic settings", Page17
4.3 Display
The display shows the current settings, options or relevant information.
The red bar above or below a symbol indicates which value is active or can be changed.
Symbol Name Use
Fill the water tank Prompt to fill the water tank
→"Steam", Page11
Empty the water tank Prompt to empty the water tank
→"After every steam operation", Page12
Descale Prompt to descale the appliance
→"Descaling", Page23
Descale Descaling programme interrupted
→"Descaling interrupted", Page23
Temperature too high The temperature in the cooking compartment is too high for the operating mode;
leave the appliance to cool down
→"Residual heat", Page8
Childproof lock activ-
ated
The childproof lock is activated
→"Childproof lock", Page16
Temperature display Appliance is heating
→"Temperature display", Page8
4.4 Types of heating
Here you can find an overview of the types of heating. You can find recommendations on using the types of heating.
Use the function selector to set the types of heating.
Symbol Type of heating and
temperature range
What it's used for/how it works
CircoTherm hot air
1
30-200°C
Bake and roast on one or more levels.
The fan distributes the heat from the ring-shaped heating element in the back
wall evenly around the cooking compartment.
CircoTherm gentle
125-200°C
Cook selected dishes gently on one level without preheating.
The fan distributes the heat from the ring-shaped heating element in the back
wall evenly around the cooking compartment. The food is cooked in phases us-
ing residual heat.
Always keep the appliance door closed when cooking.
This type of heating is used to determine the energy consumption in air recircu-
lation mode and the energy efficiency class.
Bread baking setting
1
180-240°C
For baking bread, bread rolls and baked goods that require high temperatures.
Reheat
2
80-180°C
For gently reheating food or for crisping up baked goods.
Pizza setting
30-275°C
Cook pizza or dishes that require a lot of heat from below.
The bottom heating element and the ring-shaped heating element in the back
wall heat the cooking compartment.
Full-surface grill
30-275°C
From 275°C:
Grill flat items such as steak and sausages, or make toast. Gratinate food.
The entire area underneath the grill element becomes hot.
Circo-roasting
1
30-250°C
Roast poultry, whole fish and larger pieces of meat.
The grill element and the fan switch on and off alternately. The fan circulates the
hot air around the food.
1
Steam-assist cooking possible from 80°C and over (water tank must be filled before operating)
2
Steam heating function (water tank must be full before appliance is operated)
en Familiarising yourself with your appliance
8
Symbol Type of heating and
temperature range
What it's used for/how it works
Top/bottom heating
1
30-275°C
Traditionally bake or roast on one level. This type of heating is ideal for cakes
with moist toppings.
The heat is emitted evenly from above and below.
This type of heating is used to measure the energy consumption in the conven-
tional mode.
1
Steam-assist cooking possible from 80°C and over (water tank must be filled before operating)
2
Steam heating function (water tank must be full before appliance is operated)
4.5 Functions
Here you can find an overview of the functions. Use the function selector to set the functions.
Note:If you operate your appliance with the HomeConnect app, even more functions are available for you. You can
find more information about this in the app.
Symbol Name Use
Oven light Illuminate the cooking compartment without heating.
→"Lighting", Page9
Remote start
Start and operate the appliance via the Home Connect app. →Page18
Descale Descaling your appliance keeps it working properly.
→"Descaling", Page23
Programme For many types of food, the appliance has preprogrammed setting values that
you can use.
→"Programme", Page15
4.6 Temperature and setting levels
There are different settings for the types of heating and
functions.
The settings appear in the display.
The temperature can be set in 1 degree increments up
to 100°C, and in 5 degree increments thereafter.
Note:For temperature settings above 275°C for the
Grill type of heating, the appliance reduces the temper-
ature to approx. 250°C after approx. 20minutes.
Temperature display
The temperature display shows you the temperature in
the cooking compartment.
Notes
¡ The temperature indicator only shows the temperat-
ure increasing for operating modes for which you
can set a temperature, e.g. for cleaning functions,
the temperature display is filled immediately.
¡ Due to thermal inertia, the temperature displayed
may differ slightly from the actual temperature inside
the cooking compartment.
As soon as the appliance heats up, the symbol ap-
pears in the display.
The lines are filled from the bottom to the top as the
cooking compartment heats up.
When you are preheating the appliance, the optimal
time to place your food in the cooking compartment is
when the symbol first goes out.
Residual heat
When the appliance is switched off, the temperature in-
dicator shows the residual heat in the cooking com-
partment.
The further the temperature drops, the more lines go
out.
If flashes in the display, the temperature in the cook-
ing compartment is too high for the selected operating
mode. Switch the appliance off, wait until it has cooled
down and then switch it back on again.
Accessories en
9
4.7 Cooking compartment
The functions in the cooking compartment make your
appliance easier to use.
Rails
The rails in the cooking compartment enable you to
place accessories at different heights.
→"Accessories", Page9
Your appliance has four shelf positions. The shelf posi-
tions are numbered from bottom to top.
You can remove the rails, e. g. for cleaning.
→"Shelf supports", Page24
Self-cleaning surfaces
The back wall in the cooking compartment is self-clean-
ing. The self-cleaning surfaces are coated with a por-
ous, matt ceramic layer and have a rough surface.
When the appliance is in operation, the self-cleaning
surfaces absorb splashes from roasting or grilling and
break them down.
If the self-cleaning surfaces no longer clean themselves
adequately during operation, heat up the cooking com-
partment specifically to the right temperature.
Lighting
The oven light lights up the cooking compartment.
With most types of heating and functions, the lighting
lights up during operation. When the function selector
is turned to bring operation to an end, the lighting goes
out.
The Oven light setting on the function selector can be
used to switch on the light without heating.
Cooling fan
The cooling fan switches on and off depending on the
appliance's temperature. The hot air escapes above
the door.
ATTENTION!
Do not cover the ventilation slot above the appliance
door. The appliance overheats.
▶
Ensure that the ventilation slots are unobstructed.
To ensure that the appliance cools down more quickly
after operation, the cooling fan continues to run for a
certain period afterwards.
Appliance door
If you open the appliance door during operation, the
operation continues.
5 Accessories
Use original accessories. These have been made espe-
cially for your appliance.
Note:Accessories may become deformed if they get
hot. Deformation has no effect on function. As the ac-
cessory cools down, it will regain its original shape.
The accessories supplied may differ depending on the
appliance model.
Accessories Use
Wire rack ¡ Cake tins
¡ Ovenproof dishes
¡ Cookware
¡ Meat, e.g. roasting joints or steak
¡ Frozen meals
Universal pan ¡ Moist cakes
¡ Baked items
¡ Bread
¡ Large roasts
¡ Frozen meals
¡ Catching dripping liquids, e.g. fat when
grilling food on the wire rack.
5.1 Locking function
The locking function prevents the accessories from tilt-
ing when they are pulled out.
You can pull out the accessories approximately halfway
without them tipping. The accessories must be inserted
into the cooking compartment correctly for the tilt pro-
tection to work properly.
en Before using for the first time
10
5.2 Sliding accessories into the cooking
compartment
Always slide accessories into the cooking compartment
correctly. This is the only way to ensure that accessor-
ies can be pulled out approximately halfway without tip-
ping.
1.
Turn the accessories so that the notch is at the
rear and is facing downwards.
2.
Insert accessories between the two guide rods for
the shelf position.
Wire rack Insert the wire rack with the open
side facing the appliance door and
the curved lip facing downwards.
Baking tray
E.g. univer-
sal pan or
baking tray
Slide the tray, e.g. the universal pan,
in with the sloping edge facing the
appliance door.
3.
Push the accessory all the way in, making sure that
it does not touch the appliance door.
Note:Take any accessories that you will not be using
out of the cooking compartment while the appliance is
in operation.
Combining accessories
You can combine the wire rack with the universal pan
to catch any liquid that drips down.
1.
Place the wire rack on the universal pan so that
both spacers are on the rear edge of the univer-
sal pan.
2.
Insert the universal pan between the two guide rods
for a shelf position. In so doing, the wire rack is on
top of the upper guide rod.
Wire rack
on univer-
sal pan
5.3 Other accessories
You can purchase other accessories from our after-
sales service, specialist retailers or online.
You will find a comprehensive range of products for
your appliance in our brochures and online:
www.neff-international.com
Accessories vary from one appliance to another. When
purchasing accessories, always quote the exact
product number (E no.) of your appliance.
You can find out which accessories are available for
your appliance in our online shop or from our after-
sales service.
6 Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
6.1 Initial use
You need to make settings for initial use before you
can use your appliance.
Setting the time on the clock
Once the appliance has been connected to the mains
or following a power failure, the time flashes on the dis-
play. The time starts at "12:00". Set the current time.
Requirement:The function selector must be set to the
"Off" position .
1.
Use the or button to set the time.
2.
Press the button.
a The time that is set appears on the display.
Tip:You can go to the basic settings →Page17 to
specify whether or not the time should be shown on
the display.
Reference to setting the water hardness
▶
Set the water hardness.
→"Setting the water hardness", Page18
6.2 Cleaning the appliance before using it
for the first time
Clean the cooking compartment and accessories be-
fore using the appliance to prepare food for the first
time.
1.
Remove any accessories and leftover packaging,
such as polystyrene pellets, from the cooking com-
partment.
2.
Before heating the appliance, wipe the smooth sur-
faces in the cooking compartment with a soft, damp
cloth.
3.
Fill the water tank.
→"Filling the water tank", Page12
4.
Keep the room ventilated while the appliance is
heating.
5.
Set the type of heating with steam assistance and
the temperature.
→"Steam-assisted cooking", Page11
→"Basic operation", Page11
Type of heat-
ing
CircoTherm hot air with steam
assistance
Basic operation en
11
Temperature 200 ºC
Cooking time 30 minutes
6.
Switch off the appliance after the specified cooking
time.
7.
Wait until the cooking compartment has cooled
down.
8.
Empty the water tank and dry the cooking compart-
ment.
→"After every steam operation", Page12
9.
Set the type of heating with steam assistance and
the temperature.
Type of heat-
ing
Top/bottom heating
Temperature 240°C
Cooking time 30 minutes
10.
Switch off the appliance after the specified cooking
time.
11.
Wait until the cooking compartment has cooled
down.
12.
Clean the smooth surfaces with soapy water and a
dish cloth.
13.
Clean the accessories using soapy water and a dish
cloth or soft brush.
7 Basic operation
7.1 Switching on the appliance
▶
Turn the function selector to any position other than
the "Off" position .
a The appliance is switched on.
7.2 Switching off the appliance
▶
Turn the function selector to the "Off" position .
a The appliance is switched off.
7.3 Setting the type of heating and
temperature
1.
Use the function selector to set the type of heating.
2.
Use the temperature selector to set the temperature
or grill setting.
a The appliance starts heating after a few seconds.
3.
When your food is ready, switch off the appliance.
Tips
¡ The most suitable type of heating for your food can
be found in the description of the type of heating.
→"Types of heating", Page7
¡ You can also set a cooking time and end time on
the appliance.
→"Time-setting options", Page13
Changing the type of heating
You can change the type of heating at any time.
▶
Use the function selector to set the required type of
heating.
Changing the temperature
You can change the temperature at any time.
▶
Use the temperature selector to set the required
temperature.
8 Steam
You can switch on steam assistance with some heating
types.
WARNING‒Risk of scalding!
Hot steam may escape when you open the appliance
door. Whether or not you can see steam depends on
its temperature.
▶
Do not stand too close to the appliance when open-
ing the door.
▶
Open the appliance door carefully.
▶
Keep children at a safe distance.
WARNING‒Risk of burns!
The water tank may heat up while the appliance is in
operation.
▶
Wait until the water tank has cooled down from the
previous operation.
▶
Remove the water tank from the tank recess.
8.1 Steam-assisted cooking
When you cook with steam assistance, the appliance
introduces steam into the cooking compartment at vari-
ous intervals. This gives your food a crispy crust and a
shiny surface. Meat stays juicy, tender and only under-
goes a minimum reduction in volume.
Starting steam-assisted cooking
Tip:Use the programmes or the settings in the tables.
1.
Fill the water tank.
→"Filling the water tank", Page12
2.
Set a suitable type of heating:
– CircoTherm hot air
– Top/bottom heating
– Circo-roasting
– Bread baking setting
3.
Set a temperature between 80and 240°C.
4.
Use the button to set the steam intensity.
Intensity Setting
Low
en Steam
12
Intensity Setting
High
a The appliance starts to heat and produce steam
after a few seconds.
Cancelling steam-assisted cooking
▶
Press the button repeatedly until the steam in-
tensity goes out in the display.
a The appliance continues to operate but without
steam assistance.
→"After every steam operation", Page12
Ending steam-assisted cooking
1.
Switch off the appliance.
2.
Empty the water tank and dry the cooking compart-
ment.
→"After every steam operation", Page12
8.2 Reheating
With the "Reheating" type of heating, you can gently
reheat food that has already been cooked or crisp up
day-old baked goods. The appliance switches the
steam onautomatically.
Starting reheating
Requirement:The cooking compartment has cooled
down.
1.
Fill the water tank.
→"Filling the water tank", Page12
2.
Use the function selector to set the "Reheating"
type of heating.
3.
Use the temperature selector to set the temperature.
a The appliance starts to heat and produce steam
after a few seconds.
Ending reheating
1.
Switch off the appliance.
2.
Empty the water tank and dry the cooking compart-
ment.
→"After every steam operation", Page12
8.3 Filling the water tank
WARNING‒Risk of fire!
Due to the hot surfaces, vapours from flammable li-
quids may catch fire in the cooking compartment (ex-
plosion). The appliance door may spring open. Hot
steam and jets of flame may escape.
▶
Do not pour flammable liquids (e.g. alcoholic drinks)
into the water tank.
▶
Only fill the water tank with water or with the descal-
ing solution we have recommended.
WARNING‒Risk of burns!
The water tank may heat up while the appliance is in
operation.
▶
Wait until the water tank has cooled down from the
previous operation.
▶
Remove the water tank from the tank recess.
Requirement:The water hardness has now been set
correctly.
→"Setting the water hardness", Page18
1.
Press on the water tank and pull the water tank
out .
2.
Press on the water tank lid and unscrew it .
3.
Fill the water tank with water up to the mark .
4.
Press on the water tank lid and screw it on .
5.
Place the water tank back in the opening and press
it down until it clicks into place .
Refilling the water tank
If an audible signal sounds and "Fill water tank" ap-
pears in the display, refill the water tank.
Note:If you do not refill the water tank, operation of the
appliance continues without steam-assisted cooking.
1.
Remove and refill the water tank.
2.
Refit the filled water tank.
8.4 After every steam operation
The remaining water is pumped back into the water
tank after every operation with steam. Then empty and
dry the water tank and the cooking compartment.
Emptying the water tank
WARNING‒Risk of burns!
The water tank may heat up while the appliance is in
operation.
Time-setting options en
13
▶
Wait until the water tank has cooled down from the
previous operation.
▶
Remove the water tank from the tank recess.
ATTENTION!
Drying the water tank in the hot cooking compartment
leads to damage to the water tank.
▶
Do not dry the water tank in the hot cooking com-
partment.
Cleaning the water tank in the dishwasher will damage
it.
▶
Do not clean the water tank in the dishwasher.
▶
Clean the water tank with a soft cloth and standard
washing-up liquid.
1.
Press on the water tank.
2.
Pull out the water tank.
3.
Unscrew the lid on the water tank.
4.
Empty the water tank, clean it with detergent and
then rinse it thoroughly with clean water.
5.
Dry all parts with a soft cloth.
6.
Rub the seal on the lid until dry.
7.
Leave the water tank to dry with the lid open.
8.
Place the lid on the water tank and screw it on.
9.
Insert the water tank.
Drying the cooking compartment
WARNING‒Risk of burns!
The appliance becomes hot during operation.
▶
Allow the appliance to cool down before cleaning.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120°C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
Requirement:The cooking compartment has cooled
down.
1.
Remove any dirt from the cooking compartment.
2.
Dry the cooking compartment with a sponge.
3.
Remove limescale marks with a cloth soaked in vin-
egar, then rinse with clean water and dry with a soft
cloth.
4.
Leave the appliance door open for 1 hour so that
the cooking compartment dries completely.
9 Time-setting options
Your appliance has different time-setting options, with
which you can control its operation.
9.1 Overview of the time-setting options
With the button, select the different time-setting op-
tions.
Time-setting
option
Use
Timer The timer can be set independently
of the appliance when it is in opera-
tion. It does not affect the appliance.
Cooking time If you set a cooking time, operation
of the appliance stops automatically
once this time has elapsed.
End time For the cooking time, you can set the
time at which operation ends. The
appliance starts up automatically so
that it finishes cooking at the re-
quired time.
Time You can set the time.
9.2 Setting the timer
The timer runs independently of the appliance when it
is in operation. The timer can be set when the appli-
ance is switched on or off, up to 23 hours and 59
minutes. The timer has its own audible signal so that
you can tell whether it is the timer or a cooking time
which has elapsed.
1.
Press the button repeatedly until is highlighted
in the display.
2.
Use the or button to set the timer duration.
Button Default value
5minutes
10 minutes
The timer duration can be set in 30-second incre-
ments up to 10 minutes. Above 10 minutes, the
time increments become longer the higher the
value.
a The timer starts and the timer duration begins to
count down after a few seconds.
a An audible signal sounds and the timer duration is
zero in the display when the timer duration has
elapsed.
3.
Once the timer duration has elapsed:
‒ Press any button to switch off the timer.
Changing the timer
You can change the timer duration at any time.
Requirement: is highlighted on the display.
▶
Use the or button to change the timer duration.
a The appliance applies the change after a few
seconds.
Cancelling the timer
You can cancel the timer duration at any time.
Requirement: is highlighted on the display.
▶
Use the button to reset the timer duration to zero.
a After a few seconds, the appliance applies the
change and goes out.
en Time-setting options
14
9.3 Setting the cooking time
You can set a cooking time for operation of up to 23
hours 59 minutes.
Requirement:The type of heating and temperature or
setting are set.
1.
Press the button repeatedly until is highlighted
in the display.
2.
Use the or button to set the cooking time.
Button Default value
10 minutes
30minutes
The cooking time can be set in 1-minute increments
up to 1 hour, and then in 5-minute increments.
a The appliance starts heating and the cooking time
counts down after a few seconds.
a If the cooking time has elapsed, an audible signal
sounds and the display shows the cooking time as
zero.
3.
When the cooking time has elapsed:
‒ Press any button to end the audible signal before
it sounds.
‒ To set a cooking time again, press the button.
‒ When your food is ready, switch off the appli-
ance.
Changing the cooking time
You can change the cooking time at any time.
Requirement: is highlighted on the display.
▶
Change the cooking time using the or button.
a The appliance applies the change after a few
seconds.
Cancelling the cooking time
You can cancel the cooking time at any time.
Requirement: is highlighted on the display.
▶
Reset the cooking time to zero using the button.
a After a few seconds, the appliance applies the
change and continues to heat without a cooking
time.
9.4 Setting the end time
You can delay the time at which cooking is due to fin-
ish by up to 23 hours and 59 minutes.
Notes
¡ In order to achieve a good cooking result, do not
delay the end time once the appliance is already in
operation.
¡ Food will spoil if you leave it in the oven cavity too
long.
Requirements
¡ The type of heating and temperature or setting are
set.
¡ A cooking time is set.
1.
Press the button repeatedly until is highlighted
in the display.
2.
Press the or button.
a The display shows the calculated end time.
3.
Use the or button to delay the end time.
a After a few seconds, the appliance applies the set-
ting and the display shows the set end time.
a Once the calculated start time has been reached,
the appliance starts heating up and the cooking
time starts counting down.
a Once the time has elapsed, an audible signal
sounds and the display shows the cooking time as
zero.
4.
When the cooking time has elapsed:
‒ Press any button to end the signal prematurely.
‒ To set another cooking time, press the button.
‒ When your food is ready, switch off the appli-
ance.
Changing the end time
In order to achieve a good cooking result, you can only
change the set end time before operation starts and
the cooking time starts counting down.
Requirement: is highlighted on the display.
▶
Use the or button to delay the end time.
a The appliance applies the change after a few
seconds.
Cancelling the end time
You can delete the set end at any time.
Requirement: is highlighted on the display.
▶
Reset the end time to the current time plus the set
cooking time using the button.
a After a few seconds, the appliance applies the
change and starts heating up. The cooking time
counts down.
9.5 Setting the time on the clock
Once the appliance has been connected to the mains
or following a power failure, the time flashes on the dis-
play. The time starts at "12:00". Set the current time.
Requirement:The function selector must be set to the
"Off" position .
1.
Use the or button to set the time.
2.
Press the button.
a The time that is set appears on the display.
Tip:You can go to the basic settings →Page17 to
specify whether or not the time should be shown on
the display.
Changing the time on the clock
You can change the time on the clock at any time.
Requirement:The function selector must be set to the
"Off" position .
1.
Press the button repeatedly until is highlighted
in the display.
2.
Use the or button to change the time.
a The appliance applies the change after a few
seconds.
Programme en
15
10 Programme
The programmes help you to use your appliance to
prepare different dishes by selecting the optimum set-
tings automatically.
10.1 Cookware for programmes
You should therefore use heat-resistant cookware that
is suitable for temperatures up to 300°C.
Glass or glass ceramic cookware is best. The joint
should cover approx. two thirds of the cookware base.
Cookware made from the following material is not
suitable:
¡ Bright, shiny aluminium
¡ Unglazed clay
¡ Plastic or plastic handles
10.2 Steam
For the steam function, the appliance provides you with
programmes that allow you to prepare food easily and
professionally.
Information about the steam functions can be found un-
der Steam.
→"Steam", Page11
10.3 Programme table
In the programme table, you can find pre-programmed setting values for the listed dishes.
No. Food Cookware Weight range
Weight setting
Shelf
posi-
tions
Note
Plaited loaf, savarin Baking tray with
greaseproof paper
0.6–1.5 kg
Weight of dough
3 The cooking compart-
ment must be cold to be-
gin with.
Proving yeast dough Bowl on wire rack 0.5–1.5 kg
Weight of dough
2 The cooking compart-
ment must be cold to be-
gin with.
Wheat bread, multi-grain
wheat bread on a baking
tray
Baking tray with
greaseproof paper
0.5–2.0 kg
Weight of dough
2 The cooking compart-
ment must be cold to be-
gin with.
Wheat bread, multi-grain
wheat bread in a loaf tin
Cake tin, greased
and floured
0.8–2.0 kg
Weight of dough
2 The cooking compart-
ment must be cold to be-
gin with.
White bread on a baking
tray
Baking tray with
greaseproof paper
0.5–2.0 kg
Weight of dough
2 If you are baking two
loaves at the same time,
enter the weight of the
heavier bread.
Multi-grain rye bread Cake tin, greased
and floured
0.8–2.0 kg
Weight of dough
2 The cooking compart-
ment must be cold to be-
gin with.
Flatbread Baking tray with
greaseproof paper
0.4–1.0 kg
Weight of dough
2 The cooking compart-
ment must be cold to be-
gin with.
Chicken, unstuffed
Ready to cook, seasoned
Roasting dish without
lid or universal pan
0.9–1.5 kg
Chicken weight
2 Place in the cookware
with the breast facing up.
Chicken pieces
Ready to cook, seasoned
Roasting dish without
lid or universal pan
0.1–0.8 kg
Weight of the heav-
iest piece
3 -
Duck, unstuffed
Ready to cook, seasoned
Roasting dish without
lid or universal pan
1.3–2.5 kg
Duck weight
2 Place in the cookware
with the breast facing up.
Goose, unstuffed
Ready to cook, seasoned
Roasting dish without
lid or universal pan
2.3–4.5 kg
Goose weight
2 Place in the cookware
with the breast facing up.
Fillet of beef, medium
Ready to cook, seasoned
Roasting dish without
lid or universal pan
0.8–2.0 kg
Weight of meat
2 The meat does not need
to be seared beforehand.
Fish, whole
Ready to cook, seasoned
Roasting dish without
lid or universal pan
0.8–1.5 kg
Weight of fish
2 Place in the dish in a
swimming position.
Pork neck joint
Boned, seasoned
Roasting dish without
lid or universal pan
0.8–2.5 kg
Weight of meat
2 The meat does not need
to be seared beforehand.
en Childproof lock
16
No. Food Cookware Weight range
Weight setting
Shelf
posi-
tions
Note
Joint of pork
E.g. shoulder, seasoned,
and scored rind
Roasting dish without
lid or universal pan
1.0–2.0 kg
Weight of meat
2 Place in the cookware
fatty side up; salt the rind
well
10.4 Preparing food for the programme
Use fresh and, ideally, chilled food. Use frozen food
straight from the freezer.
1.
Weigh the food.
The weight of the food is required in order to cor-
rectly set the programme.
2.
Add the food to the cookware.
3.
Place the cookware onto the wire rack.
Always place the cookware into the cooking com-
partment while it is cold.
10.5 Setting a programme
The appliance selects the optimal type of heating, tem-
perature and cooking time. All you need to do is set
the weight.
Notes
¡ You can set the weight only in the intended area.
¡ After the programme starts, you can no longer
change the programme and the weight.
Requirement:The cooking compartment has cooled
down.
1.
Fill water tank
2.
Use the function selector to set Programme .
a appears in the display.
3.
Use the or button to set the programme.
4.
Set the weight using the temperature selector.
a The appliance will start heating.
a Once the dish is ready, the appliance stops heating
and a signal sounds.
5.
If required, continue to cook the dish.
‒ Use the button to set the amount of extra cook-
ing time you want to add.
6.
Switch off the appliance.
11 Childproof lock
You can secure your appliance to prevent children
from accidentally switching it on or changing the set-
tings.
Note:You can go to the basic settings →Page17 to
specify whether you want the option to set the child-
proof lock.
You can use the childproof lock to lock the control ele-
ments of the appliance only.
11.1 Automatic childproof lock
When the appliance is switched off, it locks automatic-
ally. You need to pause the automatic childproof lock
before you switch on the appliance.
You can activate and deactivate the automatic child-
proof lock in the basic settings.
→"Basic settings", Page17
Pausing the automatic childproof lock
Requirement:The automatic childproof lock is activ-
ated in the basic settings.
→"Basic settings", Page17
▶
Press and hold the button until goes out on
the display.
11.2 Childproof lock
If you activate the childproof lock, the appliance is
locked until you deactivate the childproof lock. If you
switch off the appliance after the next operation, the
childproof lock is not activated automatically.
Activating the childproof lock
▶
Press and hold the button until appears on the
display.
Deactivating the childproof lock
▶
Press and hold the button until goes out on
the display.
12 Rapid heating
To save time, you can shorten the preheating time for
set temperatures over 100°C.
You can use rapid heating for the following types of
heating:
¡ CircoTherm hot air
¡ Bread baking setting
¡ Top/bottom heating
12.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note:Do not set a cooking time until rapid heating has
come to an end.
1.
Set a suitable type of heating and a temperature of
at least 100°C.
Basic settings en
17
2.
Press the button.
a appears in the display and the arrows are filled
from the bottom to the top.
a Rapid heating starts after a few seconds.
a Once rapid heating has ended, an audible signal
sounds and the symbol goes out in the display.
3.
Place the food in the cooking compartment.
13 Basic settings
You can configure the appliance to meet your needs.
13.1 Overview of the basic settings
Here you can find an overview of the basic settings and factory settings. The basic settings depend on the features
of your appliance.
Display Basic setting Selection
Automatic childproof lock = no
1
= yes
Signal duration upon completion of a cook-
ing time or timer period
= 10 seconds
= 30 seconds
1
= 2 minutes
Waiting time until a setting is adopted = 3 seconds
1
= 6 seconds
= 10 seconds
Button tone when pressing a button = off
= on
1
Brightness of the display illumination = dark
= medium
1
= bright
Time display = hide the time
= display the time
1
Childproof lock can be adjusted = no
= yes
1
Interior lighting during operation = no
= yes
1
Cooling fan run-on time = short
= medium
1
= long
= extra long
Telescopic shelves retrofitted
2
= no
1
(for rails and 1-level pull-out)
= yes (for 2- and 3-level pull-out)
Sabbath mode available = no
1
= yes
Water hardness
→"Setting the water hardness", Page18
= softened
= soft (up to 1.5mmol/l)
= medium (1.5–2.5mmol/l)
= hard (2.5–3.8mmol/l)
1
= very hard (above 3.8mmol/l)
Reset all values to factory settings = no
1
= yes
.. HomeConnect Settings
→"HomeConnect ", Page18
1
Factory setting (may vary according to model)
2
Depending on the appliance specifications
13.2 Changing basic settings
Requirement:The appliance is switched off.
1.
Press and hold the button for approximately
fourseconds.
a The first basic setting appears in the display,
e.g. .
2.
Use the temperature selector to change the setting.
en HomeConnect
18
3.
Use the or button to switch to the next basic set-
ting.
4.
To save the changes, press and hold the button
for approx. fourseconds.
Note:Your changes to the basic settings will be re-
tained even after a power failure.
13.3 Discarding changes to the basic
settings
▶
Turn the function selector.
a All changes are discarded and not saved.
13.4 Setting the water hardness
ATTENTION!
If the wrong water hardness has been set, the appli-
ance cannot remind you to descale it at the right time.
▶
Set the water hardness correctly.
Using unsuitable liquids may damage the appliance.
▶
Do not use distilled water, highly chlorinated tap wa-
ter (>40 mg/l) or other liquids.
▶
Only use cold, fresh tap water, softened water or
non-carbonated mineral water.
Requirements
¡ Before you set the water hardness, ask your water
supplier about the hardness of your tap water.
¡ The appliance must be switched off.
1.
Press and hold the button for approximately
fourseconds.
a The first basic setting appears in the display,
e.g. .
2.
Use the or button to switch to the next basic set-
ting .
3.
Use the temperature selector to set the water hard-
ness.
Tip:If your tap water is very hard, we recommend
that you use softened water. If you use only
softened water, you can set your appliance to the
"softened" water hardness range.
Tip:If you use mineral water, set the water hardness
range to "very hard". If you use mineral water, you
must only use non-carbonated mineral water.
Water hardness
basic setting
Water
hardness
in mmol/l
German
hardness
in °dH
French
hardness
°fH
=
softened
1
- - -
=soft Up to 1.5 Up to 8.4 Up to 15
= me-
dium
1.5-2.5 8.4-14 15-25
= hard 2.5-3.8 14-21.3 25-38
=very
hard
2
Above
3.8
Above
21.3
Above 38
1
Only set this if you will be using solely softened
water.
2
Also set for mineral water. Only use non-carbon-
ated mineral water.
4.
To save the changes, press and hold the button
for approx. fourseconds.
14 HomeConnect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the HomeConnect app, adjust its basic settings
and monitor its operating status.
The HomeConnect services are not available in every
country. The availability of the HomeConnect function
depends on the availability of HomeConnect services
in your country. You can find information about this at:
www.home-connect.com.
The HomeConnect app guides you through the entire
login process. Follow the instructions in the HomeCon-
nect app to configure the settings.
Tips
¡ Please consult the documents supplied by
HomeConnect.
¡ Please also follow the instructions in the HomeCon-
nect app.
Notes
¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the HomeCon-
nect app.
→"Safety", Page2
¡ Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the HomeConnect
app.
¡ In networked standby mode, the appliance requires
a maximum of2W.
14.1 Setting up HomeConnect
Requirements
¡ The appliance is connected to the power supply and
is switched on.
¡ You have a smartphone or tablet with a current ver-
sion of the iOS or Android operating system.
¡ The smartphone and the appliance are within range
of your home network's Wi-Fi signal.
1.
Download the HomeConnect app.
2.
Open the HomeConnect app and scan the follow-
ing QR code.
HomeConnect en
19
3.
Follow the instructions in the HomeConnect app.
14.2 HomeConnect Settings
You can adjust the settings and network settings for HomeConnect in the basic settings for your appliance.
Setting Selection or display Explanation
Connection to the network
– Not connected
– Connect automatically
– Connect manually
– Connected
and are displays that you cannot set.
Connection to the HomeConnect
app
– Ready
– Connect
– Connected
and are displays that you cannot set.
Wi-Fi
– Off
– Activate
– On
If Wi-Fi is activated, you can use HomeConnect.
In networked standby mode, the appliance requires a max-
imum of 2W.
is a display that you cannot set.
Remote start
– Deactivated
– Manual
1
– Permanent
When remote start is deactivated, you can only view the oper-
ating status of the appliance in the app.
For manual remote start, you must activate the remote start
each time before you can start the appliance via the app. If
you open the appliance door within 15minutes of activating
remote start or of the operation ending, remote start is deactiv-
ated.
For permanent remote start, you can start and operate the ap-
pliance remotely at any time.
Software update
– Update available
– Start update
The setting is only displayed if an update is available.
is a display that you cannot set.
Remote Diagnostics
– Not authorised
1
– Authorised
The setting is only displayed if after-sales service is attempting
to access the appliance.
1
Factory setting
14.3 Operating the appliance with the
HomeConnect app
You can use the HomeConnect app to set and start
the appliance remotely.
WARNING‒Risk of fire!
Combustible objects that are left in the cooking com-
partment may catch fire.
▶
Never store combustible objects in the cooking
compartment.
▶
Never open the appliance door if there is smoke in-
side.
▶
Switch off the appliance and unplug it from the
mains or switch off the circuit breaker in the fuse
box.
Requirements
¡ The appliance is switched on.
¡ The appliance is connected to your home network
and to the HomeConnect app.
¡ In order to be able to set the appliance via the app,
the manual or permanent remote start must be se-
lected in the basic setting.
1.
To activate the remote start, set the function selector
to .
2.
Implement a setting in the app and send it to the ap-
pliance.
en Cleaning and servicing
20
14.4 Software update
Your appliance's software can be updated using the
software update function, e.g. for the purposes of op-
timisation, troubleshooting or security updates.
To do this, you must be a registered HomeCon-
nectuser, have installed the app on your mobile device
and be connected to the HomeConnectserver.
As soon as a software update is available, you will be
informed via the HomeConnectapp and will be able to
start the software update via the app. Once the update
has been successfully downloaded, you can start in-
stalling it via the HomeConnectapp if you are in your
local area network. The HomeConnectapp will inform
you once installation is successful.
Notes
¡ You can continue to use your appliance as normal
while updates are downloading. Depending on your
personal settings in the app, software updates can
also be set to download automatically.
¡ We recommend that you install security updates as
soon as possible.
14.5 Remote diagnostics
Customer Service can use Remote Diagnostics to ac-
cess your appliance if you contact them, have your ap-
pliance connected to the HomeConnect server and if
Remote Diagnostics is available in the country in which
you are using the appliance.
Tip:For further information and details about the avail-
ability of Remote Diagnostics in your country, please
visit the service/support section of your local website:
www.home-connect.com
14.6 Data protection
Please see the information on data protection.
The first time your appliance is registered on a home
network connected to the Internet, your appliance will
transmit the following types of data to the
HomeConnect server (initial registration):
¡ Unique appliance identification (consisting of appli-
ance codes as well as the MAC address of the Wi-Fi
communication module installed).
¡ Security certificate of the Wi-Fi communication mod-
ule (to ensure a secure data connection).
¡ The current software and hardware version of your
appliance.
¡ Status of any previous reset to factory settings.
This initial registration prepares the HomeConnect
functions for use and is only required when you want to
use the HomeConnect functions for the first time.
Note:Please note that the HomeConnect functions
can only be utilised with the HomeConnect app. In-
formation on data protection can be retrieved in the
HomeConnect app.
14.7 Declaration of Conformity
Constructa Neff Vertriebs-GmbH hereby declares that
the appliance with Home Connect functionality meets
the essential requirements and other relevant provi-
sions of the Directive 2014/53/EU.
A detailed RED Declaration of Conformity can be found
online at www.neff-international.com among the addi-
tional documents on the product page for your appli-
ance.
2.4GHz band: 100mW max.
5GHz band: 100mW max.
BE BG CZ DK DE EE IE EL
ES FR HR IT CY LV LT LU
HU MT NL AT PL PT RO SI
SK FI SE UK NO CH TR
5GHz WLAN (Wi-Fi): For indoor use only.
15 Cleaning and servicing
To keep your appliance working efficiently for a long
time, it is important to clean and maintain it carefully.
15.1 Cleaning products
In order to avoid damaging the various oven surfaces
on the appliance, do not use unsuitable cleaning
products.
WARNING‒Risk of electric shock!
An ingress of moisture can cause an electric shock.
▶
Do not use steam- or high-pressure cleaners to
clean the appliance.
ATTENTION!
Unsuitable cleaning products may damage the sur-
faces of the appliance.
▶
Do not use harsh or abrasive cleaning products.
▶
Do not use cleaning products with a high alcohol
content.
▶
Do not use hard scouring pads or cleaning
sponges.
▶
Do not use any special cleaners for cleaning the ap-
pliance while it is hot.
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶
Never use oven cleaner in the cooking compartment
when it is still warm.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Neff B4AVH1AH0B Installation guide
- Category
- Kitchen & houseware accessories
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Neff U1CHC0AN0B Installation guide
-
Neff B5ACM7HH0B Installation guide
-
-
-
-
-
Neff B5AVM7HH0B Installation guide
-
-
Neff B5ACH7AH0B Installation guide
-
Other documents
-
Bosch HBG7241B2/01 User manual and assembly instructions
-
Siemens HR478GCB6B Installation guide
-
-
-
-
-
Siemens HB578A0S6B User manual
-
-
-