$
(/(0(17:,5(6
$77$&+('72
(;7586,21
1276+2:1
'(7$,/$
6&$/(
(1'&$3
6&5(:6)25
(1'&$3
+($775$16)(53/$7(
'
&
%
$
$
%
&
'
6,=(
%
3$5712
5(9
6&$/(1$
)
6+((72)
'21276&$/('5$:,1*
35235,(7$5<$1'&21),'(17,$/
(OHFWULFDO0IJ
WK$YH6
6HDWWOH:$
'
&
%
$
$
%
&
'
7+(,1)250$7,21&217$,1(',17+,6'5$:,1*,67+(62/(3523(57<2)
.,1*
(/(&75,&$/0)*
$1<5(352'8&7,21,13$5725$6$:+2/(:,7+2877+(:5,77(1
3(50,66,212)
.,1*(/(&75,&$/0)*
,6675,&7/<352+,%,7('
6,=(
%
5(9
)
6+((72)
/()7(1'2)
:+,7(25
:+,7(%/$&.
:,5(
5,*+7(1'2)
:+,7(25
:+,7(%/$&.
:,5(
/()7%/$&.
(/(0(17:,5(
/()7*5((1
*5281':,5(
5,*+7%/$&.
(/(0(17:,5(
5,*+7*5((1
*5281':,5(
/()7%/$&.
6833/<:,5(
/()7*5281'
6833/<:,5(
/()7:+,7(
6833/<:,5(
$)7(5$77$&+,1*
:,5(6386+:,5(6
,16,'(%2;$1'
5(3/$&((1'&$36
(/(0(17
:+,7(/,1(,1
%/$&./,1(,1
*5281',1
:+,7(:,5(
%/$&.:,5(
/,1(,121/()7-81&7,21%2;
'
&
%
$
$
%
&
'
6,=(
%
'5$:,1*12
5(9
6&$/(1$
)
6+((72)
'21276&$/('5$:,1*
35235,(7$5<$1'&21),'(17,$/
(OHFWULFDO0IJ
WK$YH6
6HDWWOH:$
'
&
%
$
$
%
&
'
7+(,1)250$7,21&217$,1(',17+,6'5$:,1*,67+(62/(3523(57<2)
.,1*
(/(&75,&$/0)*
$1<5(352'8&7,21,13$5725$6$:+2/(:,7+2877+(:5,77(1
3(50,66,212)
.,1*(/(&75,&$/0)*
,6675,&7/<352+,%,7('
6,=(
%
5(9
)
6+((72)
/()7(1'2)
:+,7(25
:+,7(%/$&.
:,5(
5,*+7(1'2)
:+,7(25
:+,7(%/$&.
:,5(
/()7%/$&.
(/(0(17:,5(
/()7*5((1
*5281':,5(
5,*+7%/$&.
(/(0(17:,5(
5,*+7*5((1
*5281':,5(
/()7%/$&.
6833/<:,5(
/()7*5281'
6833/<:,5(
/()7:+,7(
6833/<:,5(
$)7(5$77$&+,1*
:,5(6386+:,5(6
,16,'(%2;$1'
5(3/$&((1'&$36
(/(0(17
:+,7(/,1(,1
%/$&./,1(,1
*5281',1
:+,7(:,5(
%/$&.:,5(
/,1(,121/()7-81&7,21%2;
'
&
%
$
$
%
&
'
6,=(
%
'5$:,1*12
5(9
6&$/(1$
)
6+((72)
'21276&$/('5$:,1*
35235,(7$5<$1'&21),'(17,$/
(OHFWULFDO0IJ
WK$YH6
6HDWWOH:$
'
&
%
$
$
%
&
'
7+(,1)250$7,21&217$,1(',17+,6'5$:,1*,67+(62/(3523(57<2)
.,1*
(/(&75,&$/0)*
$1<5(352'8&7,21,13$5725$6$:+2/(:,7+2877+(:5,77(1
3(50,66,212)
.,1*(/(&75,&$/0)*
,6675,&7/<352+,%,7('
6,=(
%
5(9
)
6+((72)
Fig. C
1. Remove heater from carton. Disassemble the aluminum heating
panel from the back support frame. Remove knock out in junction
box for electrical supply connection. See Figure A & B.
2. To install the back support frame on the wall, locate the studs in
the wall and use existing mounting holes or pre-drill 3/16” holes
as needed. Use appropriate fasteners to securely mount to wall.
See Figure B.
#$-%".."%#/$(#$-%+0'%#/$-
SAVE THESE INSTRUCTIONS
INSTALLATION
Following are some general guidelines:
•
Do not recess this cove heater.
•
Disconnect power at main panel.
•
Make certain all wiring is in accordance with all
local codes and units are properly grounded.
•
Voltage rating of heater should be the same as
supply load.
•
Do not install the heater on vinyl wall coverings.
Fig. A
3. Temporarily hang the aluminum heating panel from the top lip
of both junction boxes. This will support the heater while the
electrical connections are made and allow one person to wire
the heater without having to hold the panel at the same time.
See Figure C.
4. Connect the supply cable grounding wire to the green wire pigtail
in wiring compartment.
5. Follow the desired wiring diagram, to connect the power supply to
the heater using approved wire nuts.
Instructions for left or right side wiring
6. Heater can be wired from either side - wire one side only.
Caution: Power wires should be connected on one side only.
In the opposite junction box, connect the white and black element wires together
using an approved wire nut. See Figures D and E.
Fig. B
MOUNTING HOLE