Anchor AN-1000X Owner's manual

Type
Owner's manual
BASS
VOLUME
TREBLE
ANCHOR Audio, Inc. (310) 784-2300
100-0026-000 / Revision D, 06/97
Owners Manual
AN-1000X
Having trouble with the sound system?
Condition Possible Solution
No sound (power LED not lit): turn POWER switch on
plug in power cord
check for blown fuse
No sound (power LED lights): check for output from source
make sure all cables are completely plugged in
increase volume control
Distorted sound: check input cable connection
lower input signal level
Excessive hum or noise: use shielded input cable
Mic volume too low: set balanced input to mic-level
Blows fuse with auxiliary speaker: shorted speaker cable
Troubleshooting Guide
100-26-0/D, ANX 2/6/01 9:40 AM Page 1
Specifications
11
General
Rated power output: 50 watts continuous
90 watts dynamic
Max SPL @ rated power: 103 dB @ 1 meter
Frequency response: 65 Hz – 20 kHz ±3dB
Speaker type: 4.5 inch woofer with shielded magnet.
10mm dome tweeter, ferro-fluid cooled
Tone controls: (bass) +8/-12 dB @ 100 Hz
(treble) +10/-12 dB @ 10 kHz
Inputs
Balanced input: female XLR, switchable phantom power
15 volts DC @ 6.8 k
Mic-level setting: Lo-Z
Line-level setting: Bridging (10 k)
Line input: Hi-Z, unbalanced, 1⁄4"-phone and RCA
Sensitivity for rated output:
Balanced; mic-level setting: -56 dBv (1.5 mVrms)
Balanced; line-level setting: -18 dBv (125 mVrms)
Line: -18 dBv (125 mVrms)
Outputs
Line output (post fader): Lo-Z, buffered, RCA
Speaker output: 8, unswitched, 1/4"-phone
AC Power requirements 110 - 125 VAC, 50/60 Hz
208 - 240 V~, 50/60 Hz
(90 watts max)
Dimensions (HWD): 5
1
4 x 8
3
8 x 9", 3.3 x 21 x 23 cm
Weight: 9.5 pounds, 4.3 Kg.
Specifications subject to change without notice.
Important Safeguards
2
CAUTION: To reduce the risk of electric shock, do not remove the cover.
No user-serviceable parts inside. Refer servicing to qualified personnel.
WARNING: To prevent fire or electric shock, do not expose this equipment to
rain or moisture.
ATTENTION: Pour eviter les risques de choc électrique, ne pas enlever le
couvercle. Aucun entretien de pièces intérieures par l'usager. Confier
l'entretien au personnel qualifié.
AVIS: Pour eviter les risques d'incendie ou d’électrocution, n'exposez pas cet
article à la pluie ou a l'humidité.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to humans.
The exclamation point, within an equilateral triangle, is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
EXPLICATION DES SYMBOLES GRAPHIQUES
Le symbole éclair avec point de flèche à l'intérieur d'un triangle équilatéral est utilisé
pour alerter l'utilisateur de la presence à l'intérieur du coffret de “voltage
dangereux” non isolé d'ampleur suffisante pour constituer un risque d'elétrocution.
Le point d'exclamation à l'intérieur d'un triangle équilatéral est employé pour alerter
les utilisateurs de la présence d'instructions importantes pour la fonctionnement et
l'entretien (service) dans le livret d'instruction accompagnant l'appareil.
DATE OF MANUFACTURE
The date of manufacture of this Anchor Audio product can be determined by
the seven or eight digit serial number code. The fifth and sixth digits from the
right denote the year, the seventh digit (letter) from the right denotes the
month (A=Jan, B=Feb, etc.) Example: "XD960083" states that the unit was
manufactured in April of 1996. An "X" may or may not exist as the eighth
digit (letter) and has no significance in the serial number or date code.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISQUE DE CHOC
ELECTRIQUE
NE PAS OUVRIR
AVIS
100-26-0/D, ANX 2/6/01 9:40 AM Page 3
The AN-1000X is a powered speaker which allows you to
monitor the signal from many types of input sources.
Here’s how easy it is to use
1. Place the AN-1000X at desired listening location.
2. Plug the power cord into a grounded AC outlet.
3. Plug an audio source into one of the three input jacks
on the back panel:
LINE IN; RCA jack
LINE IN; 1/4-inch phone jack
BALANCED INPUT; XLR jack (*see below)
4. Set the volume knob on front panel to minimum,
then turn power switch on back panel ON (the red
LED on the front panel of the unit should light).
5. Adjust the volume bass and treble for desired sound
output.
* The BALANCED INPUT jack is set at the factory for
microphone-level inputs with 15 volts DC phantom
power. See page 7 for instructions on how to change
the configuration of this input jack.
Blank Page
10
Table of Contents
3
Thank you for choosing an Anchor Audio portable sound system. Our products
incorporate state-of-the-art design and the finest quality of materials and
workmanship. We’re proud of our products and appreciate the confidence which
you have shown by selecting an Anchor system.
I hope you’ll take a few of minutes to review this manual. We’ve incorporated
several unique features into our products, and your knowledge of how to use
them will enhance the performance and your enjoyment of the system.
David Jacobs, President on behalf of all Anchor employees
Quick Use Guide
Problems?
Consult the
troubleshooting
section on the
back page of
this manual.
100-26-0/D, ANX 2/6/01 9:40 AM Page 5
Blank Page
9
Getting Started
4
Inspection and inventory of your system
Check unit carefully for damage which may have occurred
during transit. Each Anchor product is carefully inspected at
the factory and packed in a special carton for safe transport.
Inventory
• AN-1000X powered monitor
• AC power cord.
• Warranty, Owner’s Manual and registration card
All damage claims must be made with the freight carrier.
Notify the freight carrier immediately if you observe any
damage to the shipping carton or product. Repack the unit
in the carton and await inspection by the carrier’s claim agent.
Notify your dealer of the pending freight claim.
Returning your unit for service or repairs
Should your unit require service, contact your dealer or our
Customer Service Department at (310) 784-2300 to obtain a
Return Authorization (RA) number. All shipments to Anchor
must include an RA number and must be shipped prepaid.
C.O.D. shipments will be refused and returned at your cost.
Warranty registration
Please fill out the warranty card and return it with a copy of
your invoice to Anchor’s Customer Service Department. This
will activate your limited two year warranty.
Save the
shipping carton
and packing
materials. They
were specially
designed to
ship your unit
safely.
100-26-0/D, ANX 2/6/01 9:40 AM Page 7
Accessories
8
MIC-90 Handheld Microphone
Anchor’s dynamic, balanced, low impedance microphone
with a unidirectional pick-up pattern. It has an on/off switch
and comes with a 20' cable and mic clip.
AN-1001X Companion Speaker
Unpowered speaker for use with the AN-1000X. It has a
1/4"-phone input jack and parallel input/output wire
terminals. (Designed to accept Omnimount® 25-series
mounting brackets) Speaker cable not included.
SS-250 Speaker Stand
Collapsible speaker stand. Rated load capacity 25 pounds.
(Requires SB-1 bracket.)
SB-1 Stand Mounting Bracket
U-shaped swivel bracket. Mounts to a wall, ceiling or on a
speaker stand (adapter included).
RM-1 Single Rackmount Kit
Mounts one AN-1000X in a standard equipment rack .
RM-12 Dual Rackmount Kit
Mounts two AN-1000X’s in a standard equipment rack .
SC-50 Speaker Cable
Heavy duty 50' speaker cable.
Feedback Information
5
What causes feedback?
Feedback is a ringing, howling, or shrill sound that is self-
generated by the sound system. It is the result of sound from
the speakers being picked up by the microphone(s) in use
and then re-amplified by the system. This can form a self-
sustaining loop that can damage the sound system if allowed
to continue.
To prevent feedback:
ALWAYS STAND BEHIND THE SPEAKER
WHEN USING A MICROPHONE.
CAUTION: Feedback can damage your equipment and may be
hazardous to your hearing. To avoid feedback, always make
sure volume controls are at minimum before turning unit on.
If feedback occurs, immediately reduce the volume.
100-26-0/D, ANX 2/6/01 9:40 AM Page 9
LINE IN
Balanced Input
The balanced XLR jack input allows the AN-1000X to be
used in a variety of applications. The input can be configured
by the user for use with Lo-Z microphone or bridging
balanced line-level inputs (such as used in the pro-audio and
broadcast industry). In addition, the input has 15 volt
phantom power which may be switched on or off.
To set the input, remove the rubber grommet just above
the XLR input to expose the configuration switch. With a
small pointed object, slide the three dip switches to the con-
figuration required as shown below.
Line Inputs
The line-level inputs (RCA and 1/4"-phone) may be used
with input sources such as VCR's, cassette and CD players,
musical instruments, computers, mixing consoles, etc. Both
inputs may be used simultaneously on the AN-1000X—the
volume control will control the composite program output.
Line Output
The line-level output provides a replica of the composite
input signal. Use it for direct recording, or to daisy-chain
additional powered sound systems to the AN-1000X for
greater crowd coverage.
NOTE: All line-level connections must be made with shielded
cable to avoid hum, buzzing or radio interference.
Speaker Output
The external speaker output jack (1/4"-phone, unswitched)
allows the user to power an auxiliary unpowered speaker
(such as the AN-1001X). The auxiliary speaker must have a
minimum impedance of 8 ohms.
POWER
two-way powered monitor
LINE OUT
SPEAKER OUT
(8 OHM)
LINE IN
BALANCED
INPUT
FUSE
MIC LINE
Operation
7
LINE OUT
SPEAKER OUT
(8 OHM)
Operation
6
ALWAYS use
shielded audio
cables on all
input connec-
tions to prevent
interference
AN-1000X Rear Panel
MIC LEVEL
phantom power ON
LINE LEVEL
phantom power OFF
MIC LEVEL
phantom power OFF
factory setting
BALANCED
INPUT
rubber grommet
Operating the system
1. Place the AN-1000X at desired listening location.
2. Plug the power cord into a grounded AC outlet.
3. Plug an audio source into one of the three input jacks
on the back panel:
LINE IN; RCA jack
LINE IN; 1/4-inch phone jack
BALANCED INPUT; XLR jack (*see below)
4. Set the volume knob on front panel to minimum,
then turn power switch on back panel ON (the red
LED on the front panel of the unit should light).
5. Adjust the volume bass and treble for desired sound
output.
* The BALANCED INPUT jack is set at the factory for
microphone-level inputs with 15 volts DC phantom
power. See page 6 for instructions on how to change
the configuration of this input jack.
Line Output
(RCA jack)
Line Input
(1/4"-phone jack)
Balanced Input
Switch
Balanced Input
(3-pin XLR jack)
Line Input
(RCA jack)
Speaker Output
(1/4"-phone jack)
Power Switch
AC Cord Receptacle
100-26-0/D, ANX 2/6/01 9:40 AM Page 11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Anchor AN-1000X Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages