soyond 3000W Power Inverter Modified Sine Wave Converter for Home Car RV User manual

Brand: soyond

Model: 3000W Power Inverter Modified Sine Wave Converter for Home Car RV

Type: User manual

IMPORTANT: SPECIFICALLY, PLEASE NOTE THAT THE GLOBAL LF INVERTER CHARGER SHOULD NOT BE USED IN CONNECTION WITH LIFE SUPPORT SYSTEM OR

OTHER MEDICAL EQUIPMENT OR DEVICES.

BEFORE USING THE INVERTER, YOU NEED READ AND SAVE THE SAFETY INSTRUCTIONS.

Thank you for purchasing a Soyond product. Manufactured to a high standard, this product will, if used according to these instructions

and maintained properly, give you years of trouble free performance.

Refer to Instruction

Manual

INSTRUCTIONS FOR:

BATTERY LOW-VOLT DISCONNECTOR

12V/ 24V DC INPUT, 100-200 AMP

MODEL NO’s: BLP100-12, BLP100-24, BLP150-12

BLP150-24, BLP200-12, BLP200-24

1. SAFETY

BLP series Issue: 1 - 07/11/17

DANGER! - Beware, lead-acid batteries generate explosive gases during normal battery operation.

Wash with soap and water immediately if battery acid contacts skin or clothing. If acid enters eye, flush immediately with cool,clean running

water for at least 15 minutes and seek immediate medical attention.

DO NOT smoke or allow a spark or flame in the vicinity of the battery or engine.

If the battery terminals are corroded or dirty, clean them before attaching the leads.

WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow them to

touch the battery terminals.

Before attaching to battery, remove personal metallic items such as rings, bracelets, necklaces and watches. A lead acid battery can produce

a short-circuit current which is high enough to weld such items and cause severe burns.

2. INTRODUCTION

3. INSTALLATION

Back-up batteries at communication sites may be damaged by over-discharge when AC power is lost for extended periods. Unless power is restored

in a timely fashion, transceivers will continue to draw current from the batteries long after any usable voltage has been drained from them. In some

cases, connection to a battery at low voltage damages the transceiver itself.

To protect site batteries and equipment against damage and to help avoid any unnecessary down-time from overdischarge situations, installation

of a Low Voltage Disconnect is recommended. The BLP contains a special sense and control circuit housed in a compact, rugged, sealed aluminum

case. It is installed in-line with the power leads between the battery and the load. The unit continually monitors battery voltage and if it should fall

below a preset voltage threshold, the BLP disconnects the load, preventing further discharge. When the battery is recharging and voltage is raised

above another preset voltage threshold, the load is automatically reconnected.

>>Battery

>>General Information

Batt

Charger

FUSE

DC LOADS

1 2

Gen Starter

Interface definition

1: sensor output

2: GND

6: 5V

Other ports only for factory test

SOYOND

BLP series Issue: 2 - 07/11/17

The BLP should be mounted securely at a convenient location between the battery and the load. Both horizontal and vertical mounting are

acceptable.

The unit contains a relay which is not ignition protected, therefore it should not be mounted inside of a closed battery box where explosive gases

may accumulate. The case is electrically isolated from the input, output and ground terminals so mounting on either a metal or non-metal surface is

acceptable.

1. Disconnect all batteries and loads, keep away from flammable and explosive materials and take protective tools.

2. Install BLP by wiring diagram. Use sealant to seal screws to prevent from loosing when the vibration.

3. Connect ‘BAT +’ to the battery positive terminal with a wire that meets the requirements (the wrong input and output connections will damage the

protector and not be covered by the warranty.)

4. Connect ‘OUT’ to DC loads positive terminal.

5. When installing the wire, please use a wrench to fix the bottom nut.

6. Connect the BLP ground wire to the battery negative or ground terminal. Connect all batteries wires.

1. Install all devices according to the diagram.

2. Turn on the DC loads, wait the battery voltage down to BLP cut output. LED OFF.

3. Start Charger or Alternator, wait the battery voltage up and BLP recover to output. LED ON.

4. Gen starter voltage test:

Before test please check voltage between port 2 and 6 higher than 5V.

generator off: voltage between port 1 and 2 is 2.45-2.54V

generator on: voltage between port 1 and 2 is higher than 2.55V.

>>Test before using

4. SPECIFICATION

Model BLP100-12 BLP100-24 BLP150-12 BLP150-24 BLP200-12 BLP200-24

DC voltage 12V 24V 12V 24V 12V 24V

Disconnect voltage 10.5V 21.0V 10.5V 21.0V 10.5V 21.0V

Connect voltage 13.4V 26.2V 13.4V 26.2V 13.4V 26.2V

Control

Delay w ork

Peak current

Sustained current

Standby pow er consumption

Working consumption

Working temp

Safety standards

EMC standard

Output connection

Dimension/ Weight

127*85*75mm/ 0.5kg 127*110*75mm/ 0.6kg

127*110*75mm/ 0.6kg

5mA

-20℃~50℃

IEC60950

EN55022， EN61000-4-2,3,4,5,6,8,11, EN61000-3-2,3, EN50204

M8 bolts

MOSFET

30S

120A 200A

100A 150A 200A

127*110*75mm/ 0.6Kg

240A

soyond 3000W Power Inverter Modified Sine Wave Converter for Home Car RV User manual

soyond 3000W Power Inverter Modified Sine Wave Converter for Home Car RV User manual

soyond 3000W Power Inverter Modified Sine Wave Converter for Home Car RV User manual

Other documents