Toro Suspension Seat Kit, 300 Series Z Master Installation guide

Brand: Toro

Model: Suspension Seat Kit, 300 Series Z Master

Type: Installation guide

Toro Suspension Seat Kit, 300 Series Z Master is an easy-to-install upgrade for your riding mower that provides a more comfortable ride, even on rough terrain. The kit includes a suspension seat, spacer blocks, bolts, nuts, and lock washers. The suspension seat features a cushioned handle that allows you to adjust the firmness of the suspension to your liking. The spacer blocks and bolts are used to mount the seat to the mower's seat pan. The nuts and lock washers are used to secure the seat in place.

Once installed, the Toro Suspension Seat Kit, 300 Series Z Master will provide you with a more comfortable ride, even on rough terrain. The suspension seat will absorb shocks and vibrations, reducing fatigue and back pain. The cushioned handle allows you to adjust the firmness of the suspension to your liking, so you can find the perfect setting for your comfort.

Printed in the USA

 2002 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Suspension Seat Kit

Z300 Series Z Master



Part No. 105-1669

Form No. 3328–205 Rev A

Installation Instructions

Loose Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Suspension Seat

Spacer blocks

Bolts

Nuts

Lock washer

Installing the seat

No loose parts for this section Connecting the wire harness

Removing the Existing Seat

1. Tip seat forward and disconnect the wire connector

from the seat switch.

2. Remove the 4 bolts holding the existing seat to the seat

pan.

3. Remove the existing seat.

Installing the Seat

1. Remove the bolt, spacer, lock washer, and nut from the

bottom of the seat (Fig. 1).

2. Position the spacer blocks and seat onto the seat pan

(Fig. 1).

3. Install the bolts up into the seat pan, spacer blocks, and

the seat (Fig. 1).

4. While holding the bolts, secure the seat with lock

washers and nuts (Fig. 1).

m–6284

Figure 1

1. Seat

2. Spacer blocks

3. Seat pan

4. Nut

5. Bolt

6. Lock washer

Installing the Wire Harness

1. Locate the existing traction unit wire harness connector

that was connected to the old seat switch.

2. Cut the connector off the existing traction unit wire

harness (Fig. 2).

m–6286

Figure 2

1. Old traction unit wire

harness

2. Connector on old harness

3. Cut connector off

3. Strip approximately 3/8 inch of insulation form the end

of each harness wire (Fig. 3).

4. Plug the two single wires of the old wire harness into

the 2 connectors from the new seat switch (Fig. 3).

5. Crimp the connectors to secure the wires.

m–6287

Figure 3

1. New seat

2. Wires from existing

traction unit harness

3. Connector from new seat

4. 3/8 inch of exposed wire

Operating the Seat

1. Rotate the seat cushion handle either direction to get the

desired suspension (Fig. 4).

2. Use the seat suspension indicator for finding and

helping remember correct seat suspension (Fig. 4).

m–6285

Figure 4

1. Seat

2. Seat cushion handle

3. Seat suspension indicator

Installing the Decal

1. Raise the seat up.

2. Remove the backing off the decal and place the decal

on the righthand frame. See Figure 3.

m–6305

Figure 5

1. Righthand fuel tank 2. Decal

Toro Suspension Seat Kit, 300 Series Z Master Installation guide

Toro Suspension Seat Kit, 300 Series Z Master Installation guide

Toro Suspension Seat Kit, 300 Series Z Master Installation guide

Related papers

Other documents